• Resources Recycling
• /
• v.15 no.3 s.71
• /
• pp.58-65
• /
• 2006

The applicability of the waste pulp which produced in the paper recycling process as an adsorbent for the treatment of $Ni^{2+}$ ion in wastewater has been investigated taking the initial concentration of adsorbate, temperature, the amount of adsorbent, and solution pH as the experimental variables. In addition, the effect of the concentration of coexisting solute and pre-treatment of adsorbent on the adsorbability of $Ni^{2+}$ ion were also examined. The electrokinetic potential of waste pulp was observed to be positive below pH 7.8 and negative above this pH. The adsorption reaction of $Ni^{2+}$ ion reached its equilibrium within 4 hours after the reaction was initiated and the adsorbed amount of adsorbate was found to increase with its initial concentration. The adsorbability of $Ni^{2+}$ was raised with temperature so that its adsorption reaction was considered to be exothermic, which was substantiated by thermodynamic calculation. Also, the adsorbed amount of $Ni^{2+}$ was raised with the amount of waste pulp and with pH in the range of pH $3{\sim}6$. This behavior of the adsorption of $Ni^{2+}$ according to the solution pH was well agreed with the electrokinetic characteristics of waste pulp in solution. The amount of coexisting solute was observed to reversely affect on the $Ni^{2+}$ adsorption onto waste pulp under the experimental conditions. With regard to the pre-treatment of adsorbent with NaOH, the adsorbability of $Ni^{2+}$ was increased with the concentration of NaOH to a certain extent. However, it was found to decrease contrarily when the concentration of NaOH became too high.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.24 no.4
• /
• pp.31-37
• /
• 2016

This study was conducted to investigate the effect of OH radicals on organic matter oxidation and suspended solids removal using microbubble as a pre-treatment technique to reduce the organic load of night soil in connection with sewage. The experiment was conducted for three months at HRT 4 hours using pressurized type microbubble generator. The mean SS removal efficiency was achieved 71%. The average removal efficiency of $TCOD_{Cr}$, TBOD, TN and TP were achieved for 51.5%, 47.9%, and 14.7% respectively, as scum and SS were removed by flotation separation. The removal efficiency of soluble organic matters were 25.0%, 17.1% for $SCOD_{Cr}$, SBOD by air microbubble supply. Soluble nitrogen and phosphorus were removed average of 11.9% and 7.4%, respectively. As s result, it was confirmed that soluble organic matters were removed by air microbubble supplied. Generated OH radicals when the microbubble was collapsed, can decompose the soluble organic matters. Therefore, The microbubble flotation process was installed at the front of night soil treatment process, it will contribute to the stable operation of the subsequent biological treatment facility by oxidation of the dissolved organic matters as well as removal of SS by flotation separation.

• The korean journal of orthodontics
• /
• v.46 no.4
• /
• pp.199-211
• /
• 2016

Objective: Given the considerable disagreement between the Peer Assessment Rating (PAR) index and the American Board of Orthodontics Cast-Radiograph Evaluation, we aimed to develop a novel assessment system-the Improvement and Completion of Outcome (ICO) index-to evaluate the outcome of orthodontic treatment. Methods: Sixteen criteria from 4 major categories were established to represent the pretreatment malocclusion status, as well as the degree of improvement and level of completion of outcome during/after treatment: dental relationship (arch length discrepancy, irregularity, U1-SN, and IMPA); anteroposterior relationship (overjet, right and left molar position, ANB); vertical relationship (anterior overbite, anterior open-bite, lateral open-bite, SN-MP); and transverse relationship (dental midline discrepancy, chin point deviation, posterior cross-bite, occlusal plane cant). The score for each criterion was defined from 0 or -1 (worst) to 5 (ideal value or normal occlusion) in gradations of 1. The sum of the scores in each category indicates the area and extent of the problems. Improvement and completion percentages were estimated based on the pre- and post-treatment total scores and the maximum total score. If the completion percentage exceeded 80%, treatment outcome was considered successful. Results: Two cases, Class I malocclusion and skeletal Class III malocclusion, are presented to represent the assessment procedure using the ICO index. The difference in the level of improvement and completion of treatment outcome can be clearly explained by using 2 percentage values. Conclusions: Thus, the ICO index enables the evaluation of the quality of orthodontic treatment objectively and consecutively throughout the entire treatment process.

• Journal of Microbiology and Biotechnology
• /
• v.34 no.4
• /
• pp.846-853
• /
• 2024

Adzuki bean (Vigna angularis), which provides plant-based proteins and functional substances, requires a long soaking time during processing, which limits its usefulness to industries and consumers. To improve this, ultrasonic treatment using high pressure and shear force was judged to be an appropriate pretreatment method. This study aimed to determine the optimal conditions of ultrasound treatment for the improved hydration of adzuki beans using the response surface methodology (RSM). Independent variables chosen to regulate the hydration process of the adzuki beans were the soaking time (2-14 h, X₁), treatment intensity (150-750 W, X₂), and treatment time (1-10 min, X₃). Dependent variables chosen to assess the differences in the beans post-immersion were moisture content, water activity, and hardness. The optimal conditions for treatment deduced through RSM were a soaking time of 12.9 h, treatment intensity of 600 W, and treatment time of 8.65 min. In this optimal condition, the values predicted for the dependent variables were a moisture content of 58.32%, water activity of 0.9979 a_w, and hardness of 14.63 N. Upon experimentation, the results obtained were a moisture content of 58.28 ± 0.56%, water activity of 0.9885 ± 0.0040 a_w, and hardness of 13.01 ± 2.82 g, confirming results similar to the predicted values. Proper ultrasound treatment caused cracks in the hilum, which greatly affects the water absorption of adzuki beans, accelerating the rate of hydration. These results are expected to help determine economically efficient processing conditions for specific purposes, in addition to solving industrial problems associated with the low hydration rate of adzuki beans.

• Journal of Korean Society of Forest Science
• /
• v.108 no.4
• /
• pp.531-539
• /
• 2019

This study assessed the vitality of Carpinus laxiflora seeds stored for more than 15 years in order to discover optimal pre-treatment conditions for removingthe causes of seed dormancy and improving revitalization rate. Seeds were collected in October 2000 and stored at -18℃ for 16 years. Experiments to assess the revitalization ability of the seeds were performed under the following conditions: a controlled environment; in warm stratification (30 days at 23℃); in cold stratification (30 days at 4℃ andfor 30, 45, 60, and 120 days); gibberellin (GA₃) treatment (24 hours per day in GA₃ solutions of 100, 500, 1000, 2000, and 3000 mg·L^-1); and both cold stratification and GA₃ treatment (30 days at 4℃, then in a GA₃ solution of 100, 500, and 1000 mg·L^-1 for 2 hours). The average germination percentage(GP) of untreated seeds was 2%, and the average GP of warm-stratification seeds was 10%. Cold-stratification seeds had the highest GP at 81% for the 45-day process, while the 120-day cold-stratification seeds had the lowest GP at 67.3%. The average GP of seeds treated with GA₃ ranged from 77% (100 mg·L^-1) to 99% (1000 mg·L^-1), indicatingsignificant differences between the treatment concentrations. The treatment effect of GA₃ was highest at 500 mg·L^-1 and 1000 mg·L^-1, and lowest at 100 mg·L^-1. The average GP of seeds treated with GA₃ following cold stratification was 68%, which was lower than the cold stratification-only (73.2%) and GA₃-only (88.4%) treatments. A comprehensive comparison of the seed germination characteristics according to the four treatments determined that a GA₃ 500 mg·L^-1 pre-treatment, with the highest average GP, was ideally suited to the revitalization of long-term stored C. laxiflora seeds. Consequently, C. laxiflora stored at -18℃ for 16 years indicated strong vitality and could be regenerated by proper pre-treatment.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.176-177
• /
• 2016

In the last few decades, attention toward atmospheric pressure plasma (APP) has been greatly increased due to the numerous advantages of those applications, such as non-necessity of high vacuum facility, easy setup and operation, and low temperature operation. The practical applications of APP can be found in a wide spectrum of fields from the functionalization of material surfaces to sterilization of medical devices. In the secondary battery industry, separator film has been typically treated by APP to enhance adhesion strength between adjacent films. In this process, the plasma is required to have high stability and uniformity for better performance of the battery. Dielectric barrier discharge (DBD) was usually adopted to limit overcurrent in the plasma, and we developed the pre-discharge technology to overcome the drawbacks of streamer discharge in the conventional DBD source which makes it possible to produce a super-stable plasma at atmospheric pressure. Simulations for the fluid flow and electric field were parametrically performed to find the optimized design for the linear jet plasma source. The developed plasma source (Plasmapp LJPS-200) exhibits spatial non-uniformity of less than 3%, and the adhesion strength between the separator and electrode films was observed to increase 17% by the plasma treatment.

• Proceedings of the Korean Environmental Health Society Conference
• /
• 2003.06a
• /
• pp.94-97
• /
• 2003

This study performed the research about the recycling basin supernatant by pre-coat filtration in the D water treatment plant at Gwangju. Choice the prompt conditions with diatomaceous earth filtration which makes contaminant reduced in the basin supernatant. Element disk of candle used in this experiment are pore size 10$\mu\textrm{m}$(R), 20$\mu\textrm{m}$(B) and 40$\mu\textrm{m}$(Y). Diatomaceous earth are cake pore size 3.5$\mu\textrm{m}$(A), 7$\mu\textrm{m}$(B) and 17$\mu\textrm{m}$(C). The filtrate concentrations were from 0.18 to 0.92$\mu\textrm{g}$/1 of Chlorophyll-a. And then, removal rate percentage were from 78.30 to 95.57(R-A). In addition SS 80%, CODMn32% COD 61%, T-N 10% and T-P 39% on the D water treatment plant. The R(40$\mu\textrm{m}$) C(17$\mu\textrm{m}$) process can be substituted of reusing the recycled water of recycling basin supernatant view of capacity and removal rate of filtrate.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.87-88
• /
• 2006

It is needed several large reservoirs and long time in order to remove suspended solid like steel fines and iron oxide at steel making factory. If removing rate of suspended solid in rolling coolant is improved, the productivity of working process can be increased and the area of reservoir can be reduced. Pre-treatment to add extra magnetization of suspended solid was studied Iron hydroxide and electrolytic dissociation were used for pretreatment. High gradient magnetic separation (HGMS) system was used for removing of magnetized suspended solid. Removing ratio showed over than 99% in the coolant containing magnetic fines. Magnetic properties of suspended solid were investigated after mixed with Al2(SO2)3 and organic flocculant by using electrochemical treatment.

• Journal of Korean Society of Water and Wastewater
• /
• v.34 no.6
• /
• pp.393-402
• /
• 2020

In the membrane process, it is important to improve water treatment efficiency to ensure water quality and minimize membrane fouling. In this study, a pilot study of membrane process using reservoir water was conducted for a long time to secure high flux operation technology capable of responding to influent turbidity changes. The raw water and DAF(Dissolved Air Flotation) treated water were used for influent water of membrane to analyze the effect of water quality on the TMP (Trans Membrane Pressure) and to optimize the membrane operation. When the membrane flux were operated at 70 LMH and 80 LMH under stable water quality conditions with an inlet turbidity of 10 NTU or less, the TMP increase rates were 0.28 and 0.24 kPa/d, respectively, with minor difference. When the membrane with high flux of 80 LMH was operated for a long time under inlet turbidity of 10 NTU or more, the TMP increase rate showed the maximum of 43.5 kPa/d. However, when the CEB(Chemically Enhanced Backwash) cycle was changed from 7 to 1 day, it was confirmed that the TMP increase rate was stable to 0.23 kPa/d. As a result of applying pre-treatment process(DAF) on unstability water quality conditions, it was confirmed that the TMP rise rates differed by 0.17 and 0.64 kPa/d according to the optimization of the coagulant injection. When combined with coagulation pretreatment, it was thought that the balance with the membrane process was more important than the emphasis on efficiency of the pretreatment process. It was considered that stable TMP can be maintained by optimizing the cleaning conditions when the stable or unstable water quality even in the high flux operation on membrane process.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.9 no.1
• /
• pp.90-98
• /
• 2001

The slow degradation rate of sewage sludge in anaerobic digesters is due to the rate limiting step of sludge hydrolysis. Therefore, the pre-treatment process had been carried out using acidic(pH 1.5, 3, 4, 5) and alkaline(pH9, 10, 13), thermal(50, 100, 150, $200^{\circ}C$) and ultrasonic treatment(400W, 20kHz, 15, 20, 25, 30, 35, 40, 50, 60min). In the best conditions of each treatment, the SCOD ratio(%) of treated/untreared samples were increased 102% in acid(pH5), 986% in alkali(pH13), 959% in thermal($200^{\circ}C$) and 1123% in ultrasonic(35min) treatment. As the result, the ultrasonic treatment was most effective, followed by alkali, thermal, acidic treatment. In the effects of total gas productivity, the thermal($200^{\circ}C$) pretreatment was the highest, followed by thermal($150^{\circ}C$), ultrasonic(90min), alkaline(pH9) and ultrasonic(50min).