• 한국자동차공학회논문집
• /
• 제16권1호
• /
• pp.71-77
• /
• 2008

This paper proposes an Electronic Throttle Body (ETB) model considering a non-linearity of DC motor driver which is integrated with a H-bridge and a gate driver. A propagation delay and reverse recovery time of switching components cause non-linear characteristic of DC motor driver. This non-linearity affects not only the amateur voltage of DC motor, but also entire behaviour and parameters of ETB. In order to analyze the behavior of ETB more accurately, this non-linear effect of DC motor driver is modeled. The developed ETB model is validated by use of the step response and ramp response experiments, and it shows relatively accurate results compared with linear DC motor driver model.

• 한국자동차공학회논문집
• /
• 제21권3호
• /
• pp.58-65
• /
• 2013

In this paper, we propose that a model based design for an electric motor cycle system using ASM (Automotive Simulation Models). Before prototyping a realistic electric motorcycle, a reliable simulation program is required to test the capacities of the power sources and optimize the parameters of an electric motorcycle. Because ASM is based on Simulink, we can design the drivetrain and powertrain of the vehicle model systems easily. To verify the electric motorcycle system analysis of design parameters such as max power, capacity, state of charge and slope angle is carried out by the simulation and experimental method. The predicted results by the development model were in good agreement with the experimentally obtained results. Therefore, the proposed electric motorcycle model can effectively reduce the expenses during the designing of an electric motorcycle system.

• 한국자동차공학회논문집
• /
• 제13권6호
• /
• pp.38-47
• /
• 2005

In this paper, a regenerative braking algorithm is proposed to make the maximum use of the regenerative braking energy for an independent front and rear motor drive parallel HEV. In the regenerative braking algorithm, the regenerative torque is determined by considering the motor capacity, motor efficiency, battery SOC, gear ratio, clutch state, engine speed and vehicle velocity. To implement the regenerative braking algorithm, HEV powertrain models including the internal combustion engine, electric motor, battery, manual transmission and the regenerative braking system are developed using MATLAB, and the regenerative braking performance is investigated by the simulator. Simulation results show that the proposed regenerative braking algorithm contributes to increasing the battery SOC, which recuperates 60 percent of the total braking energy while satisfying the design specification of the control logic. In addition, a control algorithm which limits the regenerative braking is suggested by considering the battery power capacity and dynamic response characteristics of the hydraulic control module.

• 한국자동차공학회논문집
• /
• 제16권2호
• /
• pp.183-190
• /
• 2008

This paper deals with the characteristics of idle vibration due to the type of constant velocity joints. Based on the kinematics model of constant velocity joints, a offset between the tripod center and tullip center plays a important role in generating unwelcome forces. Moreover, it induced additional forces in lateral direction of a vehicle movement according to the angle of the spider in idle vibration. The difference of mass for each constant velocity joint types affect the natural frequency of the driveshaft and the powertrain. When the static torque is applied to the constant velocity joints, the natural frequencies of the driveshaft are reduced nearby 50Hz. There will be a big opportunity that the dirveshaft and constant velocity joints would be a transfer path of idle vibration at D or R gear range. Experiments indicate that TJ type is better than SFJ and DOJ in idle vibration.

• 한국자동차공학회논문집
• /
• 제16권2호
• /
• pp.58-65
• /
• 2008

The finite element programs have been developed for structure, collision, flow, dynamics, heat transfer, acoustics, electromagnetism, MEMS (Micro Electro Mechanical Systems), and etc. These programs can be classified as either "package" program or "single purpose" program. Single purpose programs usually have convenient and powerful functions, but these programs have limited expandability to different fields of analysis. Therefore, the method to converter the analysis results of single purpose program to other programs is needed. In the research, multi-body data conversion methods of 1) finite element model and 2) solid model were created to convert fluid analysis result of CFD-ACE+ to ANSYS data structure. Automatic boundary condition algorithms were developed for blade, and finite element model was compared with solid model. It is expected that, by sealess data transfer, the Multi-body Data Conversion Program could reduce the development period of torque converters.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제12권3호
• /
• pp.201-213
• /
• 2012

A gear type lubrication pump is an essential component of the powertrain and has a major role for supplying oil to the gears and bearings in automatic transmission with a hydraulic clutch. Therefore, the durability test code design of lubrication pump is very important to ensure the reliability of the entire transmission and the vehicle. In this study, the design process for the life testing of lubrication pump has been generalized by four steps. The four design steps of the life testing of lubrication pump consist of the configuration of load spectrum, rain flow counting and analysis of load level, the equivalent damage assessment and test code generation. In fact, the load spectrum should be obtained from the field operating condition but that kind of data is the top secret of manufacturers. This is not open to the public in general. So we could use the artificially simulated load spectrum instead of field obtained one and focused on the development of the general process for designing the life test of a gear type lubrication pump. Reliability goals for lubrication pump, pressure, torque, temperature and load spectrum, if present, as appropriate for the given test conditions, accelerated life testing for the lubrication pump can be designed by the developed design steps.

• 한국기계가공학회지
• /
• 제15권5호
• /
• pp.48-56
• /
• 2016

In this paper, we analyze the power flow of an eight-speed automatic transmission by using a lever analogy for the manufacturing of planetary gears. The results indicate that the engine power is passed down to the carrier and ring gear in the first double pinion planetary gear (DPPG1), and to the sun gear, carrier, and ring gear in DPPG3 for the first speed. Although the power flow is similar in the second speed, the power circulation occurs in the second single pinion planetary gear (SPPG2). For the third speed, the engine power is passed from the carrier to the ring gear in DPPG, at which point the power is split between the sun gears of SPPG2 and DPPG3.

• Advances in Automotive Engineering
• /
• 제1권1호
• /
• pp.105-121
• /
• 2018

The hybrid electric powertrain is a robust solution that allows for major improvements in both fuel economy and emission reduction. In the present study, a through-the-road hybrid vehicle model with an electric motor driving the rear axle and an Internal Combustion Engine (ICE) driving the front axle has been constructed. We then present a systematic method for the determination of a real time applicable optimal Energy Management Strategy (EMS) for a hybrid road vehicle. More precisely, we compare the performance of rule-based EMS strategies to an optimization-based strategy, namely ECMS (Equivalent Consumption Minimization Strategy). The comparison is conducted in parallel with a parameterization of the size of the internal combustion engine and the implementation of a Continuously Variable Transmission (CVT) that allows following the line of best fuel economy. For the FTP-75 driving cycle, the constrained engine On-off control algorithm is shown to offer a 28% improvement potential of fuel consumption compared to the conventional internal combustion engine while the ECMS strategy achieves an improved potential of nearly 33%.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.690-695
• /
• 2000

This article deals with the analytic results on the development and application of the Spherical CVT. The Spherical CVT is marked by its simple configuration, the infinite torque multiplication characteristic, and the smooth transitions between forward/neutral/reverse states of output speed. In this study, we describe the conceptual principles behind the Spherical CVT and some applications of it, which we developed recently. And, we propose the shifting algorithm based on the analytic consideration of CVT powertrain system. Contrary to conventional shifting algorithms using the OOL(optimal operating line) of the power source, the proposed shifting algorithm is represented as a $2^{nd}$ order equation in an explicit form, and it reveals the possibility of theoretic design of all optimal controller. As an example, we present numerical results that demonstrate the energy saving possible and the proposed shifting algorithm from the use of the Spherical CVT over standard reduction gear unit, using an ideal dc motor model.

• Journal of Power Electronics
• /
• 제17권5호
• /
• pp.1203-1210
• /
• 2017

This paper presents an improved switching selection method for the direct torque control (DTC) of five-phase induction motors (IMs). The proposed method is conducted using optimal switching selection. A five-phase inverter has 32 voltage vectors which are divided into 30 nonzero voltage vectors and two zero voltage vectors. The magnitudes of the voltage vectors consist of large, medium, and small voltage vectors. In addition, these vectors are related to the torque response and torque ripple. When a large voltage vector is selected in a drive system, the torque response time decreases with an increased torque ripple. On the other hand, when a small voltage vector is selected, the torque response time and torque ripple increase. As a result, this paper proposes an optimal voltage vector selection method for improved DTC of a five-phase induction machine depending on the situation. Simulation and experimental results verify the effectiveness of the proposed control algorithm.