• Journal of the Korean Ceramic Society
• /
• v.42 no.4
• /
• pp.269-275
• /
• 2005

We analyzed the unit cell performance against the cathode porosity, which is supposed to be closely related with active sites for the cathode reaction. In order to fabricate the unit cells with different porosity in the cathode layer we changed the mixing ratio of fine and coarse LSCF cathode powders. The final porosity of each cathode layer was 14, 23, 27, $39\%$ respectively. According to the electrochemical analysis of unit cell performance via DC current interruption and AC impedance method, the electrodic polarization resistance was diminished as the cathode porosity increased. The decrease of polarization resistance was attributed due to the increase of active reaction sites and the enhancement of overall unit cell performance could be explained in the same line.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.1
• /
• pp.21-28
• /
• 2017

The steel-plate concrete(SC) is used in a form of module assembly construction in the outer wall of nuclear-power plant and LNG containment. Since the steel-plate concrete modules are generally manufactured from the plant, the weight of SC has significantly effect on the total construction cost in the aspect of shipment. Therefore, the use of lightweight aggregates concrete(LWAC), which fill the inside of SC module can be a solution. However, the amount of used lightweight aggregates(LWA) is limited in the use of current concrete mixing process due to the concrete quality problems and it also determines the allowable minimum density of LWAC. In this research, the preplaced casting method is applied because of increasing the volume fraction of LWA significantly, which results from the producing process of pre-packing the LWA in the formwork and filling the interstitial voids between LWA using cement paste grout. The density and compressive strength of selected preplaced LWAC were $1,600kg/m^3$ and 30MPa and it was applied for the mock-up specimens of SC panel. It was used for the 3-point bending test for evaluating its structural performance. The results show that the preplaced LWAC can reduce the density of concrete with the adequate mechanical and structural performance.

• Journal of Navigation and Port Research
• /
• v.39 no.3
• /
• pp.217-222
• /
• 2015

In this research, sea routes of domestic coaster liners between 2005 and 2013 were studied via social network analysis. Study of the sea routes revealed that they follow power-law in a scale-free form, a characteristic found often in social network. We have looked into centrality, which is a major standard in the field of social network analysis. We have also analyzed the annual changing trend in the centrality of the connectivity, examined the effect of quantity through the comparison with the original quantitative analysis method, and lastly, verified the relationship between the centrality of connectivity and mediation. Then, we were able to identify ports according to priority using these factors. This research assumed and interpreted the coaster liners route as a single network and suggested useful results. Based on these results, directing of development of domestic coaster liners route development and other factors will be achieved more smoothly. And if we utilize social network analysis method in other various fields - for example, the centrality of airport and the diplomatic realations analysis of the neighboring country - we will be able to effectively analyze events in diverse perspectives.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.7
• /
• pp.586-593
• /
• 2014

The CNUSAIL-1 project aims to develop and operate a 3U-sized cube satellite with solar sail mechanism. The primary mission is to successfully deploy the solar sail in a low earth orbit, and the secondary mission is to collect the scientific data for the effect of the solar sail deployment and operation on orbit maneuver and attitude change of the cube satellite. For this, the bus system will collect and transmit the dynamic data of the satellite and the visual images of the solar sail operation. This paper describes solar sail mission and conceptual design of CNUSAIL-1. The actuation/operation of the solar sail and the bus system are preliminarily designed in terms of attitude control system, communication system, electrical power system, command and data handling system, structure and thermal control system is designed.

• Korean Journal of Food Science and Technology
• /
• v.41 no.5
• /
• pp.566-571
• /
• 2009

The principal objective of this study was to use a fermentation and extrusion process in order to improve the antioxidant properties of original Sangmaksan (ES), containing maekmoondong, omija, and white ginseng. The antioxidant activities of fermented Sangmaksan prepared with different types of ginseng [white (FSW), red (FSR), and extruded white (FSE)], were investigated. The white ginseng powder was extruded at 20% moisture content and $120^{\circ}C$ of the maximum process temperature at the barrel. The antioxidant properties of Sangmaksan were increased after fermentation. Interestingly, the fermented Sangmaksan containing the extruded white ginseng evidenced more potent antioxidant properties than the fermented Sangmaksan containing white ginseng. The content of total phenolic compounds, DPPH-radical scavenging activity, acidic polysaccharide, reducing power, and total anthocyanin were highest with FSR, followed by FSE, FSW and ES, respectively. Additionally, superoxide dismutase-like activity and total flavonoid contents were highest in the fermented Sangmaksan containing extruded white ginseng. In conclusion, it can be asserted that the fermentation and extrusion process utilized in this study may prove to be an effective new process for the production of high-quality Sangmaksan.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.7
• /
• pp.504-509
• /
• 2020

This study analyzed the factors that affect the emotional intelligence of clinical dental hygienists' psychological well-being. The study was conducted from September 1, 2019 to November 30, 2019 with 180 dental hygienists living in Jeollabuk-do province. The data was analyzed by independent t-tests, one-way ANOVA, Scheffé test, Pearson's correlation coefficient, and stepwise multiple regression using SPSS 18.0. Psychological well-being has a significant correlation with emotional intelligence (r=.596, p<.001). Emotional intelligence of clinical dental hygienists was found to be significant in a suitable regression model (F=116.575, p<.05), and the explanatory power was 53.6%. The higher the psychological well-being was, the higher the emotional intelligence was. The factors related to emotional intelligence of clinical dental hygienists were psychological well-being, self-acceptance, positive relations to others, personal growth, environmental mastery and clinical experience. The results of this study show that psychological well-being is related to emotional intelligence. It is necessary to establish an effective strategy to enhance the psychological well-being of clinical dental hygienists and strengthen their emotional intelligence.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.32 no.3
• /
• pp.31-38
• /
• 1990

The power water flowed out from the multipurpose darn influences the ecosystem approximately because of the low water temperature. An appropriate counter measure to the rising water temperature is needed for growing crops especially when the temperature is below 18˚C in the source of the irrigation water This observational study is practiced in Yong-Doo water warming canal and pond in the down stream of Choong-Ju multipurpose dam and is practiced for analyse and compare the rising effects in actural water temperature by actual measurement with the rising effects of planned water temperatuer by the basic theoritical method and for the help to present the direction in plan establishment through investigate the results afterwards. The results are as follows. 1.The degree of the rise of the water temperature can be decided by $\theta$x=$\theta$o +K L--v.h (T-$\theta$˚)Then, K values of a factor representing the characteristics of the water warming canal were 0.00002043 for the type I. and 0.0000173 for the type II. respectively. 2.A variation of water temperature which produced by the difference effective temperature and water temperature in the water warming canal was $\theta$x1 = 16.5 + 15.9(1-e -0.00018x), $\theta$x2 =18.8 + 8.4( 1-e -0.000298x)for the type I. and $\theta$x, = 19.6 + 12.8 ( 1-e -0.00041x) for the type II. 3.It was shown that the effects of the rise of water temperature for the type I. water warming canal were greater than that of type II. as a resultes of broadening the surface of the canal compared with the depth of water, coloring the surface of water canal and installing the resistance block. 4.In case of the type I. water warming canal, the equation between the air temperature and the degree of the rise of water temprature could be made ;Y= 0.4134X + 7.728 In addition, in case of the type II. water warming canal, the correlation was very low. 5.A monthly variation of the water temperature in the water warming canal was the highest in August during the irrigation period and the water temperature rose with the air temperature until August. However, it was blunted after then. 6.A rising degree of water temperature of the practical value in the water warming pond was higher than that of the theoritical equation by 69% for the type I. and 57% for the type II. Accordingly, it was possible to acquire the result near the practical value.$\theta$w-$\theta$o=[1-exp{ -h(1+2$\psi$) . X($\theta$w-$\theta$0)XC Here, C values are 1.69 for the type I. and 1.57 for the type II. 7.It was shown that the effect of the rise of water temperature was favorable when the thermal absorption was to be good by coloring the surface of the water warming pond and removing the bottom osmosis. 8.By enlarging the surface of water in comparison with the depth, and by having dead area of water in the water warming pond, this structure in the water warming pond is helpful for the rise of water temperature.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.11
• /
• pp.949-956
• /
• 2016

There are a number of effects by solar radiation in many aerospace industrial fields, such as degradation of mechanical properties, sealing effect of sealants or decolorization. Because it takes long time to investigate these effects by using the light of natural state, new methods are developed for accelerating this phenomenon. In this paper, we developed an apparatus to simulate accelerated solar radiation phenomenon selecting irradiation intensity $1,120W/m^2$ as the designed environment. Epoxy polymer as the composite material was chosen and processed by ASTM-D638, a reference for tensile test of polymer and plastic. Total color shift was selected as the test category to evaluate acceleration of the test. We obtained acceleration factors and numerical model from test data and concluded it can shorten test periods by accelerated irradiation intensity of $1,120W/m^2$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.557-562
• /
• 2018

Unlike live ammunition which has killing power due to the use of high explosives, training ammunition has only the limited explosive effect needed for training purposes, so the risk of accidents is lowered. Because training ammunition is used in large quantities during military drills, the problem of environmental pollution occurs. As most of the waste is left out in the training field, using bio-degradable polymers such as Polylactic Acid (PLA) can provide a solution to these environmental issues. However, bio-degradable polymers such as PLA usually have poor thermal and mechanical properties compared with other general purpose polymers, so they need to be improved before they can be used for military purposes. In this study, Talc is added to the PLA used for the parts of Training Grenades to improve some of their properties and the changes of their thermal and mechanical properties were verified. In the case of the 1 wt.% ~ 5 wt.% PLA/Talc blends, the thermal properties were improved in proportion to the content of Talc, but the best mechanical properties were observed for the 1 wt.% and 3 wt.% PLA/Talc blends.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.7
• /
• pp.743-750
• /
• 2008

In water treatment plant the Dissolved Ozone Flotation(DOF) System may be employed because this system has various abilities, such that it can remove SS using microbubbles, and it can exert strong oxidation power in removing taste and odor, color, and microbial agents. In order to investigate effectiveness of the DOF system in water treatment, removal characteristics of various water quality parameters were observed depending on the different levels of ozone concentrations. Removal efficiencies of water quality parameters in DOF system were compared with those in DAF(Dissolved Air Flotation) system and in CGS(Conventional Gravity Settling) system. Optimum ozone dose obtained in the pilot experiments was 2.7 mg/L. With increasing ozone dose higher than 2.7 mg/L, removal rates of turbidity, KMnO$_4$ consumption, UV$_{254}$ absorbance, and TOC were reversely lowered. High concentration of ozone dissociate organic matter in water, so that increasing dissolved organic level in effluent. Removal rates of water quality parameters at optimum ozone dose were obtained, such that removal rates of turbidity, KMnO$_4$ consumption, TOC, and UV$_{254}$ asorbance were 88.9%, 62.9%, 47%, and 77.3% respectively. Removal rate of THMFP was 51.6%. For all the parameters listed above, the DOF system was more effective than the DAF system or the CGS system. It is found that the DOF system may be used in advanced water treatment not only because the DOF system is more efficient in removing water quality parameters than the existing systems, but because the DOF system is also required smaller area than the CGS system for the treatment plant.