• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.354-355
• /
• 2011

그 동안 스위칭 손실 저감을 위해 Si 다이오드를 SiC 다이오드로 대체한 인버터들이 많이 소개되었다. NPC 인버터에서도 마찬가지로 클램프 다이오드 소자를 SiC 다이오드로 대체함으로써 스위칭 손실을 저감시킬 수 있다. 하지만 IGBT의 스위칭 손실이 매우 크기 때문에 단지 클램프 다이오드 소자를 바꿈으로써 줄일 수 있는 스위칭 손실은 한계가 있다. 따라서 본 논문은 낮은 변조지수를 갖는 NPC 인버터에서 역회복 손실을 포함한 스위칭 손실을 최소화 시킬 수 있는 새로운 PWM 방법을 제시한다. 제안한 방법에 의해 역회복 현상은 거의 발생하지 않으며 스위칭 손실은 상당히 저감된다. 그러므로 전체 시스템 효율을 증가시킬 수 있고 인버터를 더 높은 스위칭 주파수에서 동작시킬 수 있다. 제안한 방법의 타당성은 각 소자의 성능평가와 수치해석적 방법을 적용해 검증하였다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.11 no.7
• /
• pp.253-260
• /
• 2001

A Study of interior noise reduction in the magelv train is presented. Tarin speed of interest is low such that aero-dynamic noise is negligible and power supply system is a dominant noise source. Based on the measurements of interior noise and acceleration levels during running and zero speed conditions, dominant noise sources are identified. After spectra characteristics of noise sources are investigated several noise reducing methods are studied such as STL increasement of floor panels. sealing. and absorption treatment It is found that the most important noise sources are VVVF inverter and SLM in running condition, whereas air conditioner and DC/DC converter are dominant in zero speed. Sine the major noise sources are under the floor complete sealing and high STL of the floor panel are shown to be the most crucial factors in noise reduction After sound absorbing material, which is polyurethan foam of 50 mm thickness, is thickness, is attached to the downward side of the floor in addition to sealing treatment, the interior noise is reduced by 3~4 dB.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.7
• /
• pp.1314-1320
• /
• 2001

DC motors have widely been used in the field of variable-speed driving system since it is easy to control flux and torque of the motors precisely but it is hard to check and maintain those periodically. In addition, there are difficulties in high power and high speed running due to rectifying limit of commutator, and are a lot of restrictions in installation. Therefore, speed control in BLDC(Brushless DC) motors have seriously been studied for a long while. In this paper, a mathematical model of BLDC motor driven by PWM inverter is developed. Dynamics and steady-state characteristics of BLDC motor are simulated and analyzed with a series of experiments for the parameter estimation : torque, speed, phase voltage and current.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.592-594
• /
• 2008

The powers used in the robot drive motor system are mostly DC sources such as batteries. Even AC powers in some systems are generated from DC sources by the inverter. It is can be forecasted that the DC-link communications will be widely used invarious industrial application. In this paper a novel BLDC motor drive system by using DC-link communications is proposed. The characteristic of this system is the communication only needs 2 DC lines. There are not additional lines to translate the reference signals and the reliability of the system is enhanced especially in some badly circumstance. The number of lines can be least when applied in the multi motor control system and the slip ring design can be simplified when applied as rotation machine. The reasonableness of proposed motor system is clarified by the PSIM simulation and the hardware prototype.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.4
• /
• pp.231-237
• /
• 2006

This paper proposes an effective drive of high intensity discharge (HID) lamp ballast for cars. All control functions of the proposed ballast are implemented using a low-cost single chip microcontroller, PIC16C73 to optimize the total system size and to minimize cost through minimization of total component number. The proposed ballast generates high open-circuit voltage to ignite the lamp and is controlled to supply effectively the power required to shorten warm-up period after the breakdown. The DC-DC converter of the DC-AC converter part of the ballast utilizes the flyback converter topology that can minimize component number. Also, because to more minimize the ballast size, the transformer size must be minimized, for this, PWM (Pulse Width Modulation) pulses are generated with high frequency using the PWM module of the microcontroller. An analysis for this is explained, briefly. As if the operation of the lamp and ballast arrives at steady-state, then the ballast must AC-control the lamp, for this, the microcontroller utilizes the other PWM module. And the part related to the igniter is explained, briefly. It is shown through experimental results that the controller of the proposed ballast has good performance for the HID lamp for cars.

• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.566-569
• /
• 2005

Interior permanent magnet synchronous motor(IPMSM) has become a popular choice in electric vehicle applications, due to their excellent power to weight ratio. The paper is proposed maximum torque control of IPMSM drive using artificial intelligent(AI) controller. The control method is applicable over the entire speed range and considered the limits of the inverter's current and voltage rated value. For each control mode, a condition that determines the optimal d-axis current $i_d$ for maximum torque operation is derived. This paper considers the design and implementation of novel technique of high performance speed control for IPMSM using AI controller. This paper is proposed speed control of IPMSM using learning mechanism fuzzy neural network(LM-FNN) and estimation of speed using artificial neural network(ANN) controller. The back propagation neural network technique is used to provide a real time adaptive estimation of the motor speed. The proposed control algorithm is applied to IPMSM drive system controlled LM-FNN and ANN controller, the operating characteristics controlled by maximum torque control are examined in detail. Also. this paper is proposed the experimental results to verify the effectiveness of AI controller.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.153-159
• /
• 2012

In photovoltaic system, the characteristic of photovoltaic module such as open circuit voltage and short circuit current will be changed because of cell temperature and solar radiation. Therefore, a boost converter of the PV system connects between the output of photovoltaic system and DC link capacitor of grid connected inverter as controlling duty ratio for maximum power point tracking(MPPT). This paper shows the dynamic characteristic of the boost converter by comparing single-loop control algorithm and two-loop control algorithm using both analog and digital control. The proposed both compensation method has been verified with computer simulation and simulation results obtained demonstrate the validity of the proposed control schemes.

• Journal of the Korean Solar Energy Society
• /
• v.29 no.6
• /
• pp.14-21
• /
• 2009

The demand and installation for photovoltaic system(namely, PV) has grown steadily in Korea. However, the PV system has a various economic viability according to the PV system characteristic variables such as inverter efficiency, miscellaneous power conditioning losses, azimuth and slope of PV array, PV tracking mode, and so on. The other variables are the monthly consumed electric energy and economic related factor such as initial cost, government subsidy, maintenance cost, inflation rate, energy cost escalation rate, discount rate, etc. Therefore, this study is to present economic evaluation of PV system with those concerned factors by calculating internal rate of return, year-to-positive cash flow and net present value indices.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.4
• /
• pp.45-48
• /
• 2013

The electronic device, such as flat panel display (FPD), is very important in our life as a means of communication between humans. Liquid crystal display (LCD), which is categorized as a flat panel display, has been used in many display products, especially in TV industry. An LED TV is composed of several electrical components, such as liquid critical module (LCM), analog to digital convertor (AD), power supplier, and inverter board. These modules are very vulnerable to particulate contamination, and causing malfunction or visibility degradation. In this study, we developed a test method for prediction of LCM's lifetime. The test system consists of carbon particle generation flame, dilution system, test chamber, and particle concentration monitoring instrument. Since the carbon particles are the most abundant in the atmosphere and easily absorb light, soot particles are used as a challenging material for this test. The concentration of generated soot particles is set around 4,000,000 #/cc, which is 400 times higher than that of usual atmospheric particles. Through this experiment, we deduced the relationship between the dust concentration and life time of the test specimen.

• Journal of Magnetics
• /
• v.17 no.1
• /
• pp.36-41
• /
• 2012

The transcranial magnetic stimulation recharges the energy storing condenser, and sends the stored energy in the condenser to the pulse shaping circuit, which then delivers it to the stimulating coil. The previous types of transcranial magnetic stimulation required a booster transformer, secondary rectifier for high voltages and a condenser for smooth type. The energy storing condenser is recharged by switching the high-voltage direct current power. Loss occurs due to the resistance in the recharging circuit, and the single-pulse output energy in the transcranial magnetic stimulation can be changed because the recharging voltage cannot be adjusted. In this study a booster transformer, which decreases the volume and weight, was not used. Instead, a current resonance inverter was applied to cut down the switching loss. A transcranial magnetic stimulation, which can simultaneously alter the recharging voltage and pulse repeats, was used to examine the output characteristics.