• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.41 no.5
• /
• pp.71-78
• /
• 2004

An infrared remote control-type transcutaneous control device using a $\mu$-processor is design for the totally implantable middle ear system. An infrared light transmission model for the tissue of skin was introduced and then a radiant intensity and the required current of the infrared light emitting diode(IR LED) driving circuit at transmission part were calculated for the external control device. And the transmission part generates IR signal by the system's own data protocol which prevents interferences from other infrared remote controls of the household appliances. The control part of the implanted device was designed to analyze functions of the received infrared(IR) signal that indicate the power ON/OFF and volume UP/DOWN. After the system is implemented, a data transmission experiments using 4 mm thickness of porcine skin were carried out. From the experiment, it was verified that the infrared control signal was transmitted to receiving module of the implemented system without any error.

• Journal of IKEEE
• /
• v.16 no.3
• /
• pp.274-282
• /
• 2012

In this paper, we propose the design of lighting control algorithm for intelligent LED lighting system. The proposed lighting control algorithm transmitted to MCU through a data bus the environmental information detected from respectively sensor node. The MCU control software was designed to determine the level maintained to depending on the set control method by comparing the results that calculated the dimming level using a signal value. Also, it was designed to be lighting by cross-performed periodically the rotation and reverse method by created fully symmetrical pattern using the control algorithm to LED lighting device. In this paper, the proposed lighting control algorithm improved the reliability of the data sent by designed the system that can be controlled lighting to stable, and it was maintained the event delivery ratio of 91%. Also, the lighting device was decreased the luminous intensity of 32%, the power consumption of 49%, and heat generation of 32%. As a result, it were could be improved the energy efficiency that the life-cycle of LED has been increased 50%.

• Journal of the Korea Computer Industry Society
• /
• v.10 no.4
• /
• pp.143-150
• /
• 2009

Remote control service, monitoring, gear service of information electronic appliance, various services of security service and so on of Home network that is by link of Ubiquitous environment are offered. These services need verification process through priority test to use and are changed. If test using actuality information electronic device for test, much expenses and time may be invested. Home network test bed offers softness of research using control model and simulator, in this paper, Wish to design and embody home network test bed to do environment construction of home network and test of application service. Because use istent power line just as it is without necessity to establish circuit in addition by solution of home network testbed, expense costs to be less and establishment used easy PLC. Also, propriated Wireless sensor network that use Zigbee by solution of home network testbed. Appliance check and monitor square do by Home Auto that know embodied, and embodied by Home Gateway that interlink terminals of Home Auto and out of.

• Journal of Satellite, Information and Communications
• /
• v.10 no.3
• /
• pp.26-31
• /
• 2015

This paper deals with a size-reduced Ku-band waveguide limiter. Basically, it passes the signal from 16.125 GHz through 16.375 GHz, but when excessively high power is injected to the input port, it should change to a bandstop filter. Furthermore, it is required to change to bring attenuation by more than 20 dB and 50 dB over a narrow band and the entire passband, respectively. Therefore, in order to meet this requirement, a limiting device is implemented with multiple PIN-diode posts that enable the limiter to be the bandpass filter and stopband one at the off and on states of the PIN-diode switch, respectively. So, the design goes through the equivalent circuit modelling and the geometry is realized in the accurate electromagnetic analysis CAD tool. Finally, the result is discussed to shed light on whether it complies with the aforementioned requirement.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.6
• /
• pp.18-26
• /
• 1999

This paper presents the architecture and design of a DSSS MODEM ASIC chip for wireless local area networks (WLAN). The implemented MODEM chip supports the DSSS physical layer specifications of the IEEE 802.11. The chip consits of a transmitter and a receiver which contain a CRC encoder/decoder, a differential encoder/decoder, a frequency offset compensator and a timing recovery circuit. The chip supports various data rates, i.e., 4,2 and 1Mbps and provides both DBPSK and DQPSK for data modulation. We have performed logic synthesis using the $SAMSUNG^{TM}$ $0.6{\mu}m$ gate array library and the implemented chip consists of 53,355 gates. The MODEM chip operates at 44MHz, the package type is 100-pin QFP and the power consumption is 1.2watt at 44MHz. The implemented MODEM architecture shows lower BER compared with the Harris HSP3824.

• Journal of IKEEE
• /
• v.11 no.1 s.20
• /
• pp.69-76
• /
• 2007

This paper presents the design of LVDS (Low-Voltage-Differential-Signaling) transmitter for Gb/s-per-pin operation. The proposed LVDS transmitter is designed using BiCMOS technology, which can be compatible with CMOS technology. To reduce chip area and enhance the robustness of LVDS transmitter, the MOS switches of transmitter are replaced with lateral bipolar transistor. The common emitter current gain($\beta$) of designed bipolar transistor is 20 and the cell size of LVDS transmitter is $0.01mm^2$. Also the proposed LVDS driver is operated at 1.8V and the maximum data rate is 2.8Gb/s approximately In addition, a novel ESD protection circuit is designed to protect the ESD phenomenon. This structure has low latch-up phenomenon by using turn on/off character of P-channel MOSFET and low triggering voltage by N-channel MOSFET in the SCR structure. The triggering voltage and holding voltage are simulated to 2.2V, 1.1V respectively.

• The Journal of the Convergence on Culture Technology
• /
• v.3 no.3
• /
• pp.27-30
• /
• 2017

IoT could be applied to various areas because of the important role of sensor. The existing sensor communication method is to quickly transmit data by using clock and two data pins based on the I2C serial communication method. As the objects used are gradually light-weighted and the amount of data transmission is decreased, the simplification of hardware is more emphasized as an essential design element than the speed of transmission. This paper designed a circuit to send/receive data in series, and also realized arduino, by analyzing the existing communication method and then using a single pin for light-weight. The single pin serial communication could reduce power consumption, which is suitable for the sensor area using digital communication of IoT area.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.8 s.111
• /
• pp.732-738
• /
• 2006

Divide-by-2 and divide-by-4 circuits which can operate up to 10 GHz are designed. A design method used in these circuits is the TSPC(True Single Phase Clocking) topology. The structure of the TSPC dividers is very simple because they need only a single clock and purely consist of smalt sized cmos devices. Through measurements, we find the fact that in proportion to the bias voltage, the free running frequency increases and the operation region also moves toward a higher frequency region. For operating conditions of bias voltage $3.0{\sim}4.0V$, input power 16dBm and dcoffset $1.5{\sim}2.0V$, 5 GHz and 2.5 GHz output signals divided by 2 and 4 are measured. The layout size of the divide-by-2 circuit is about $500{\times}500 um^2$($50{\times}40um^2$ except pad interconnection part).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.2
• /
• pp.191-199
• /
• 2008

In this paper, we present a performance analysis and design and implementation results of a 2.4 GHz bio-radar system that can detect human heartbeat and respiration signals. In order to design a 2.4 GHz bio-radar system qualitatively, we investigate the electromagnetic properties of human tissues and calculate the target SNR of demodulation output with respect to distance. The target SNR is defined by the 90 % success ratio for detecting heartbeat signal. With this target SNR value, the performance and link budget of the bio-radar system is simulated using MATLAB. Using this link budget results, the direct conversion receiver is designed and Implemented in 4 layer printed circuit board(PCB). With output power of 0 dBm and 5 Hz bandwidth, 80 % success ratio of 50 cm is measured. Measurement results show a good agreement with simulation results.

• The Journal of the Acoustical Society of Korea
• /
• v.15 no.5
• /
• pp.82-89
• /
• 1996

Application fields of ultrasonic transducers can be divided into two categories, a high ultrasonic resolution required field and a high ultrasonic power required field. This paper is aimed to determine the optimal properties of the matching layers of the transducer for each of the applications. Further, it is aimed to optimize the properties of the matching layers that show satisfactory performances for both of the application fields. Through the direct time domain analysis of the transmission and reflection behavior of the ultrasonic wave, apart from the conventional equivalent circuit analysis, and Fourier transformation of its results, we found the optimum acoustic impedances of the matching layers. The newly determined layers provide much better transducer performance-57% at most-than those obtained with conventional design methods. Based on the results, we also found the optimal acoustic impedances of the layers good for both of the application fields. For te optimization, we developed a new transducer performance evaluation parameter that can be applied to any type of ultrasonic transducers.