• Transactions of the Korean hydrogen and new energy society
• /
• v.26 no.5
• /
• pp.484-492
• /
• 2015

As our government is actively introducing the RPS (Renewable Portfolio Standards) as a national renewable energy obligation policy, power producers are using the various renewable energy to meet the RPS supply quota since 2012. Recently, it is appling to use power bio-fuel oil in bio-fuel oil demonstration project with power companies. In general, power bio-fuel oils are composed of mixture products of vegetable oil, animal fat, fatty acid ester and waste oil. It is already developing for a power plant as a renewable energy abroad. In Korea, it is studying a 100% combustion and blended combustion of heavy fuel oil and bio-fuel oil. In this study, we investigated fuel characteristics of mixed power bio-fuel oil and its emission performance. Especially, it was reduced emissions of bio-oil in industrial boilers due to bio-fuel properties as compare with fuel oil.

• Journal of Power System Engineering
• /
• v.17 no.6
• /
• pp.11-17
• /
• 2013

Esterified bio-diesel oil is normally used as blend oil of 3% that and 97% diesel fuel in Korea. Since specifics of it is similar to that of diesel fuel, availability of non-esterified bio-diesel oil that has a lower expenses of manufacturing is worthy of attention. However, bio-diesel oil has a demerit which it emits typically more NOx emission than diesel fuel. In this study, characteristic tests using blending oil with 95% gas oil and 5% bio-diesel oil were achieved at lower common rail pressure in order to improve this demerit. It was noticed that non-esterified bio-diesel oil has more similar characteristics to diesel fuel than esterified bio-diesel oil and it emits more NO emission by fuel NO mechanism.

• Journal of the Korean Society of Combustion
• /
• v.20 no.1
• /
• pp.15-23
• /
• 2015

This paper presents the results of field demonstration for fuel switching to bio-fuel oil in 4 commercial heavy oil fired power plants. The 100% fuel switching field demonstration was successfully carried out in two tangential-firing boilers at a capacity of 75 and 100 MWe respectively without major equipment retrofit, and also 25% bio-fuel oil blending for two opposite firing boilers at a capacity of 350 and 400 MWe respectively. Despite the low density and heating value, the bio fuel was successfully replaced heavy fuel oil at the full load by only adjusting operational parameters. Incase of bio fuel oil combustion, heat absorption of radiative heat transfer section was reduced while convection section has opposite trend. In pollutants emission, a major reductionin SOx as well as 10-20% reduction in NOx were achieved by the fuels witching. On the other hand, boiler efficiency was slightly underestimated.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.6
• /
• pp.712-720
• /
• 2017

As Korean government has activated the renewable portfolio standard (RPS) since 2012, producers have been seeking and using the various renewable resources to meet the RPS quota. One of these efforts, Power Bio-Fuel oil demonstration project is being conducted to check the operability and compatibility with fossil fuel, Fuel oil (B-C) from 2014. The oil is a mixture of vegetable oil and animal fat or fatty acid ester of them and should satisfy some specification to use the power generation. The oil's quality and combustion characteristics are different from conventional oil, Fuel oil (B-C) in current power plant facility. In this study, it was investigated the storage stability and malodor intensity of Bio-Fuel oil.

• Journal of the Korean Society of Combustion
• /
• v.19 no.2
• /
• pp.28-36
• /
• 2014

Bio fuel oil combustion experiments were successfully demonstrated at the 75 MWe oil-fired power plant without major equipment retrofit and 100% bio-fuel oil combustion was possible without big problems. The experimental data error correction was conducted and numerical model-based analysis technique was applied for the evaluation of the results. Incase of bio fuel oil combustion, heat absorption of radiative heat transfer section was reduced while convection section has opposite trend. The furnace exit gas temperature tends to rise slightly. Environment emissions such as NOx and SOx concentrations showed a tendency to decrease during the bio fuel oil combustion period. On the other hand, boiler efficiency was slightly underestimated.

• Journal of Power System Engineering
• /
• v.6 no.3
• /
• pp.11-16
• /
• 2002

This paper describes the power performance and emission characteristics of the high speed direct injection diesel engine (2.9 litter displacements) driven by soybean oil asknown a bio diesel fuel. The results were compared to diesel fuel with blending bio diesel fuels. The soybean bio diesel fuel was added in the diesel fuel in concentration varying from 25% to 75% volume rates. We measured the emissions according to ECE 13 mode and full load, fixedengine speed. When the 25% bio diesel fuel was used, NOx emission at the ECE 13 mode test slightly decreased compared with diesel base engine. Over engine speed of 2000 rpm, the level of unburned hydrocarbon(HC) and carbon monoxide(CO) were the same to the diesel engine. Smoke emission decreased asthe blending bio diesel fuel rate increased.

• Journal of the Korean Applied Science and Technology
• /
• v.32 no.3
• /
• pp.588-598
• /
• 2015

Recently, the government is actively promoting the RFS(Renewable Fuel Standards) and RPS(Renewable Portfolio Standards). Therefore, the importance of renewable energy fuel is being highlighted more than ever. Now is the time required active research in Korea. Since power bio-fuel oil demonstration project is underway dissemination to meet RPS quota. In this study, we investigated emission performance to make the performance standard draft of bio-fuel oil. In addition, the quality properties of the fuel oil and bio-oil, and after combustion in industrial boilers and compared the amount of exhaust gas. It was reduced emissions of bio-oil in industrial boilers due to bio-fuel properties as compare with fuel oil.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.4
• /
• pp.562-571
• /
• 2014

In these days, many countries carry out many renewable energy policies to increase the renewable energy portion and to reduce the GHG(Green House Gas). In Korea, RPS(Renewable Portfolio Standards) focused on over 500MW power producers is conducting. And they are using the bio-fuel oil to meet their RPS quota. The oil is a mixture of animal and vegetable fat or fatty acid ester of them and should satisfy some specifications to use the power generation such as viscosity, pour point, acid number. Depends on the raw materials, quality characteristics of power bio-fuel oil are changed. By adding the power bio-fuel oil, pour point, density, sulfur content and viscosity are decreased and acid number, iodine number, oxygen content are increased. In this study, we test the quality characteristic of power bio-fuel oil and the property changes by the blending ratio of power bio-fuel oil & conventional fuel oil.

• Journal of the Korean Applied Science and Technology
• /
• v.32 no.1
• /
• pp.136-147
• /
• 2015

As it carry out RPS(Renewable Portfolio Standards), power producers are using the power bio-fuel oil to meet their RPS quota. In this study, we test the quality characteristics of raw materials for power bio-fuel oil and the property changes of power bio-fuel oil by the kind of feedstocks. The power bio-fuel oil and feedstocks were analyzed for item of quality standard such as acid number, viscosity and metal contents. And it was analyzed for composition distribution by FT-IT and HPLC. Such as low priced palm oil series has high acid number and ash contents due to high free-fatty acid and metal contents. And by-product of biodiesel have a tendency of high viscosity. The fuel properties of power bio-fuel oil, such as viscosity, acid number and metal contents are correlated with the constituent and the mixing ratio of the feedstocks.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.985-994
• /
• 2018

Bio-heavy oil for power generation is a product made by mixing animal fat, vegetable oil and fatty acid methyl ester or its residues and is being used as steam heavy fuel(B-C) for power generation in Korea. However, if the fuel supply system of the fuel pump, the flow pump, the injector, etc., which is transferred to the boiler of the generator due to the composition of the raw material of the bio-heavy oi, causes abrasive wear, it can cause serious damage. Therefore, this study evaluates the fuel characteristics and lubricity properties of various raw materials of bio-heavy oil for power generation, and suggests fuel composition of biofuel for power generation to reduce frictional wear of generator. The average value of lubricity (HFRR abrasion) for bio-heavy oil feedstocks for power generation is $137{\mu}m$, and it varies from $60{\mu}m$ to $214{\mu}m$ depending on the raw materials. The order of lubricity is Oleo pitch> BD pitch> CNSL> Animal fat> RBDPO> PAO> Dark oil> Food waste oil. The average lubricity for the five bio-heavy oil samples is $151{\mu}m$ and the distribution is $101{\mu}m$ to $185{\mu}m$. The order of lubricity is Fuel 1> Fuel 3> Fuel 4> Fuel 2> Fuel 5. Bio-heavy oil samples (average $151{\mu}m$) show lower lubricity than heavy oil C ($128{\mu}m$). It is believed that bio-heavy oil for power generation is composed of fatty acid material, which is lower in paraffin and aromatics content than heavy oil(B-C) and has a low viscosity and high acid value, resulting in inhibition of the formation of lubricating film by acidic component. Therefore, in order to reduce friction and abrasion, it is expected to increase the lubrication of fuel when it contains more than 60% Oleo pitch and BD pitch as raw materials of bio-heavy oil for power generation.