• Journal of the Korean Chemical Society
• /
• v.58 no.1
• /
• pp.25-32
• /
• 2014

Corrosion inhibition of 304 stainless steel (SS) in 1 M HCl by aqueous extract of coriander seeds was studied using weight loss, potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) and electrochemical frequency modulation (EFM) techniques. Values of inhibition efficiency obtained are dependent upon the concentration of extract and temperature. Generally, inhibition was found to increase with inhibitor concentration, but decrease with temperature. Physical adsorption mechanism has been proposed for the inhibition with Langmuir adsorption isotherm obeyed. Values of activation energy of the inhibited corrosion reaction of 304 SS are greater than the value obtained for the blank. Thermodynamic consideration reveals that adsorption of aqueous extract of coriander seeds 304 SS surface is spontaneous.

• Corrosion Science and Technology
• /
• v.9 no.5
• /
• pp.209-215
• /
• 2010

To elucidate the effect of aging time on resistance to localized corrosion of hyper duplex stainless steel, a double-loop electrochemical potentiokinetic reactivation test a potentiodynamic anodic polarization test, a scanning electron microscope-energy dispersive spectroscope analysis, and a thermodynamic calculation were conducted. With an increase in aging time, sigma phases are precipitated much more than chi phases due to the meta-stable chi phase acting as a transition phase. As aging time at $850^{\circ}C$ increases, the corrosion resistance decreases owing to an increase in Cr, Mo and W depleted areas adjacent to the intermetallic phases such as sigma phases and chi phases.

• Journal of the Korean Chemical Society
• /
• v.57 no.2
• /
• pp.264-271
• /
• 2013

Corrosion inhibition of mild steel used in water station in 35 ppm aluminum sulfate and 10 ppm chloride solution by Camellia sinensis leaves extract was studied using weight loss, potentiodynamic polarization and electrochemical impedance spectroscopy techniques at $30^{\circ}C$. Results show that the inhibition efficiency increases with increasing concentration of the extract and decreases with increasing temperature. Inhibitive effect was afforded by adsorption of the extract's components which was found to accord with Langmuir adsorption isotherm. Inhibition mechanism is deduced from the temperature dependence of the inhibition efficiency and was further corroborated by the values of activation parameters obtained from the experimental data.

• Corrosion Science and Technology
• /
• v.8 no.6
• /
• pp.227-231
• /
• 2009

Mg and Mg alloys have been used for lots of applications, including automobile industry, aerospace, mobile phone and computer parts owing to low density. However, Mg and Mg alloys have a restricted application because of poor corrosion properties. Thus, improved surface treatments are required to produce protective films that protect the substrate from corrosive environments. Environmental friendly Plasma Electrolytic Oxidation (PEO) has been widely investigated on magnesium alloys. PEO process combines electrochemical oxidation with plasma treatment in the aqueous solution. In this study, AZ91 Mg alloys were treated by PEO process in controlling the current with PC condition and treated time, concentration of NaF, NaOH, and $Na_2SiO_3$. The surface morphology and phase composition were analyzed using SEM, EDS and XRD. The potentiodynamic polarization tests were carried out for the analysis of corrosion properties of specimen. Additionally, salt spray tests were carried out to examine and compare the corrosion properties of the PEO treated Mg alloys.

• Korean Journal of Materials Research
• /
• v.25 no.10
• /
• pp.509-515
• /
• 2015

MAO ceramic coatings were prepared on AZ61 magnesium alloy for various processing times ranging from 5 to 60 min, in an electrolyte solution based on silicate-fluoride. The mechanical, electrochemical and, microstructural properties and the phase compositions of the coating layers were investigated. In this work, unlike previous studies, coatings with high amounts of the $Mag_2SiO_4$ phase were formed which contained small amounts of MgO and $MgF_2$ at a processing condition of 30 min. A microstructural analysis revealed that the porosity of the coatings was reduced considerably with an increase in the processing time, together with a change in the pore geometry from an irregular to a spherical shape. Potentiodynamic polarization and mechanical testing results showed that the coatings acquired after a processing time of 30 min were superior to all of the others.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.3
• /
• pp.87-92
• /
• 2015

Carbon thin films were deposited on STS 316L sheets by inductively coupled plasma enhanced magnetron sputtering with or without substrate bias voltage. Typical Raman spectrum for amorphous diamond-like carbon (DLC) was obtained, and the interfacial contact resistance (ICR) was measured to show its conductive nature. The electrochemical impedance spectroscopy (EIS) was used to investigate the corrosion mechanism of the carbon coating under the polymer electrolyte membrane fuel cell (PEMFC) condition. According to the pore-corrosion mechanism, the electrolyte penetrates the carbon coating through the pores and reacts with the substrate. As the substrate corrosion proceeds, the pore enlargement occurs and the surface area of the substrate exposed to the electrolyte. Applicability of the carbon coating for the PEMFC bipolar plate was evaluated by potentiodynamic polarization experiments. Finally, an adhesion problem was briefly considered.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.549-550
• /
• 2006

The corrosion performance of a powder metallurgical aluminum alloy in aeronautical environments was studied for both as sintered and heat treated states. Sintered samples were obtained by uniaxial pressing of an Al-Cu-Mg prealloyed powder followed by liquid phase sintering. The heat treatments applied were T4 and T6. Corrosion behaviour was assessed by means of potentiodynamic polarization. Results for the equivalent commercial wrought counterpart, AA2024-T3, are also presented for comparison. Similar corrosion performance was observed for both as sintered and AA2024-T3 samples, while corrosion resistance of the PM materials was improved by the heat treatment, especially in the T4 state.

• Korean Journal of Metals and Materials
• /
• v.49 no.11
• /
• pp.839-844
• /
• 2011

We examined the effects of alloying elements such as Fe, Ga, In, Sn, Mg, and Mn on the electrochemical characteristics of Al-based alloys for Al-air batteries by potentiodynamic polarization tests and electrochemical impedance spectroscopy. The corrosion potential of an Al anode was lowered by the addition of Ga and Sn, resulting in an increase in the cell voltage compared with a pure Al electrode. Fe was not beneficial to improve the electrochemical properties of the Al anode in that it caused a decrease in the cell voltage and reduced corrosion rate slightly. In, Mn, Sn, and Mg decreased the corrosion rate of the Al alloys, while Ga enhanced corrosion significantly and accelerated consumption of the anode.

• Korean Journal of Metals and Materials
• /
• v.46 no.2
• /
• pp.53-57
• /
• 2008

This study examined the role of excess free volume on the corrosion resistance of an amorphous alloy. Corrosion behaviors were monitored on the amorphous alloys, of which amount of free volume was controlled via the isothermal annealing below the glass transition temperature, using immersion tests and potentiodynamic polarization tests in HCl aqueous solutions. It was found that the corrosion resistance of the amorphous alloy is improved by reducing the amount of excess free volume. The possible reason explaining the experimental result was discussed from the viewpoint of the internal energy associated with the annihilation of excess free volume.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.3
• /
• pp.365-376
• /
• 2021

Two arylamino substituted mercaptoimidazole derivatives namely 4,5-dimethyl-1-(phenylamino)-1H-imidazole-2(3H)-thione (I1) and 4,5- dimethyl-1-((p-chlorophenyl)amino)- 1H-imidazole-2(3H)-thione (I2) were synthesized and investigated as corrosion inhibitors for carbon steel in 0.5 M HCl solution by means of electrochemical impedance spectroscopy (EIS), potentiodynamic polarization, ATR-FTIR spectroscopy and SEM. The results showed that the investigated mercaptoimidazole derivatives act as mixed type inhibitors and inhibition efficiency follows the I2>I1 order. Adsorption of inhibitors on metal surface was found to obey the Langmuir adsorption isotherm. Thermodynamic parameters revealed that adsorption of the inhibitors has both physisorption and chemisorption adsorption mechanism. Electrochemical test results were supported by quantum chemical parameters obtained from DFT calculations.