• 한국해양공학회지
• /
• 제30권1호
• /
• pp.51-56
• /
• 2016

In this study, for the tube-to-tube friction welding of hose nipple materials, the main parameters of friction welding were investigated using tensile tests, Vickers hardness surveys of the bond area (HAZ), and observations of the microstructure to increase the quality of friction welding based on visual examination. As-welded and post weld heat treated (PWHT) specimens were tested. The optimal welding conditions were found to be n = 1000 rpm, HP = 10 MPa, UP = 15 MPa, HT = 9 s, and UT = 5 s when the metal loss (Mo) was 7.5 mm. Furthermore, the peak of the hardness distribution of the friction welded joints could be eliminated by PWHT. Moreover, the two materials of the friction weld were thoroughly mixed with a well-combined structure of micro-particles, without any molten material, particle growth, or defects.

• 대한기계학회논문집A
• /
• 제30권3호
• /
• pp.349-355
• /
• 2006

The gas turbine components is used on high temperature conditions which under severely circumstance with start-up and stop several times. Therefore, it is used nickel-base superalloys like and GTD-111DS. Damaged buckets on the t긴ade tip during operating are repaired per 24,000 hr to three times according to repair specification of manufacture. It is applied pre-heat, HIP(hot isostatic pressing) and post-heat treatment to support welding repair on blade tip effectively. On this study, It is utilize of $WRAP^{TM}$ (welding repair advanced process) method to make tension test specimens for this study, And then, material strength and characteristic for GTD-111DS was analyzed.

• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.1982-1989
• /
• 1991

본 연구에서는 AISI 강은 대부분 열처리후에 사용되는 고강도강으로 용접시 발생하는 높은 잔류응력 분포를 제거 또는 감소시키기 위해서 여러가지 방법이 사용된 다. 잔류응력 제거는 용접후 풀림처리를 하면 잔류응역이 제거된다. 그러나 풀림 처리 하기전에 용접부에 높은 잔류응력 제거는 용접후 풀림처리를 하면 잔류응력이 제 거된다. 그러나 풀림처리 하기전에 용접부에 높은 잔류응력에 의해 균열이 생성될 수 있으므로 용접시 높은 잔류응력이 생성되지 않도록 예열 및 후열처리를 필요로한 다. 그러므로 본 연구에서는 예열 및 후열이 잔류응력 분포에 어떠한 영향을 주는가 를 실험적인 방법에 의해 연구하였다.

• 대한기계학회논문집A
• /
• 제41권3호
• /
• pp.219-224
• /
• 2017

본 연구는 수송기계 축 등에 이용되는 캠 형상 부분만을 기존의 단조품인 SF45와 축 부분은 일반기계구조용 탄소강재인 SM45C를 직경 20 mm를 이용하여 이종 마찰용접을 수행하였다. 최적조건을 규명하기 위해 인장시험 등 용접품질과의 상관관계를 고찰하였고, 또한 최적조건에서 마찰용접 후 열처리를 시행하여 용접재(As-welded)와 후열처리재(PWHT)에 대한 회전굽힘 피로시험을 시행하였다. 결과적으로 두 이종재가 강한 혼합으로 계면에서도 개재물 및 산화막이 플래시로 토출되어 양호한 접합상태임을 확인하였다. 더욱이 모재(SF45)와 후열처리재의 피로한도 각각 180 MPa, 250 MPa로 나타났다. 이는 후열처리재가 SF45 모재에 비해 약 40 %의 피로수명이 향상되었음을 확인하였다.

• 한국해양공학회지
• /
• 제26권1호
• /
• pp.64-69
• /
• 2012

Dissimilar friction welds were produced using 15-mm diameter solid bars of chrome molybdenum steel (KS SCM440) and carbon steel (KS SM20C) to investigate their mechanical properties. The main friction welding parameters were selected to ensure good quality welds on the basis of visual examination, tensile tests, Vickers hardness surveys of the bond area and HAZ, and macro-structure investigations. The specimens were tested as-welded and post-weld heat treated (PWHT). The tensile strength of the friction welded steel bars was increased to 100% of the SM20C base metal under the condition of a heating time of more than four seconds. Optimal welding conditions were n = 2,000 (rpm), HP = 60 (MPa), UP = 100 (MPa), HT = 5 (s),and UT = 5 (s), when the total upset length was 7.8 (mm). The hardness distribution peak of the friction welded joints could be eliminated using PWHT. The two different kinds of materials were strongly mixed to show a well-combined structure of macro-particles, with no molten material, particle growth, or defects.

• 한국해양공학회지
• /
• 제4권2호
• /
• pp.94-99
• /
• 1990

This paper deals with investigating experimentally the effects of PWHT on the weld quality such as strength, toughness, hardness and micro-structure of the welded joints in friction welding of torsion bar material SUP9A bar to bar. The results obtained are summarized as follows; 1) It was certified that the condition of the post-weld heat treatment(PWHT) for the friction welded joints was very satisfactory because both strength and toughness of the joints were improved as almost same as those of the base metal or better by the PWHT. 2) The peak of hardness distribution of the friction welded joints can be eliminated by PWHT, resulting in being almost equalized at the weld interface, the HAZ(heat affected zone) and the base metal. 3) The micro-structure of the base meta., HAZ and weld interface(WI) of friction welded joints welded at the optimum welding condition consists of the same sorbite structure obtained by PWHT and fined sorbite at WI, resulting in increasing toughness as well as strength, and no micro structural defect has been found at the friction welded zone.

• 한국해양공학회지
• /
• 제4권2호
• /
• pp.244-244
• /
• 1990

This paper deals with investigating experimentally the effects of PWHT on the weld quality such as strength, toughness, hardness and micro-structure of the welded joints in friction welding of torsion bar material SUP9A bar to bar. The results obtained are summarized as follows; 1) It was certified that the condition of the post-weld heat treatment(PWHT) for the friction welded joints was very satisfactory because both strength and toughness of the joints were improved as almost same as those of the base metal or better by the PWHT. 2) The peak of hardness distribution of the friction welded joints can be eliminated by PWHT, resulting in being almost equalized at the weld interface, the HAZ(heat affected zone) and the base metal. 3) The micro-structure of the base meta., HAZ and weld interface(WI) of friction welded joints welded at the optimum welding condition consists of the same sorbite structure obtained by PWHT and fined sorbite at WI, resulting in increasing toughness as well as strength, and no micro structural defect has been found at the friction welded zone.

• Corrosion Science and Technology
• /
• 제16권6호
• /
• pp.278-284
• /
• 2017

The effects of TIG welding and post-treatment procedures on the microstructure and the pitting corrosion resistance of welded lean duplex stainless steel S82441 were investigated. Autogenous TIG welding was used with different amounts of heat input and shielding gases such as Ar, and mixtures of $Ar-N_2$ and Ar-He. The addition of 5% to 15% of nitrogen to argon practically did not affect the level of the pitting corrosion resistance. However, the application of gas mixtures (50% Ar + 50% He) resulted in a significant decrease in pitting corrosion resistance. We found that increased current (200 A and 250 A) led to lower values of CPT of welds compared with welds obtained with 50 A, 100 A and 150 A. In addition, the removal of the weld surface layer (0.2 ~ 0.3 mm thickness) in most cases not only resulted in a significant increase in resistance to the pitting corrosion but also post-treatment of weld, implying that corrosion resistance depended on factors such as surface roughness or the presence of undesirable oxides.

• 동력기계공학회지
• /
• 제10권1호
• /
• pp.77-82
• /
• 2006

In this study, dissimilar friction welding were produced using 15mm diameter solid bar in chrome molybedenum steel(SCM440) to carbon steel(S45C) to investigate their mechanical properties and the relationship between the weld parameters and the nondestructive coefficients, such as AE counts and ultrasonic attenuation coefficient. The main friction welding parameters were selected to endure good quality welds on the basis of visual examination, tensile tests, Vickers hardness surveys of the bond of area and heat affected zone. The specimens were tested as-welded and post weld heat treated(PWHT). The tensile strength of the friction welded steel bars was increased up to 100％ of the S45C base metal under the condition of all heating time. The ductility of PWHT specimens is higher than as-welded.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.273-275
• /
• 2002

The effect of post-weld heat treatment (PWHT) of marine structures steel was investigated at electrochemical viewpoint. In addition, slow strain rate test (SSRT) was carried out to investigate both electrochemical and mechanical properties by PWHT effect during impressed current cathodic protection. The optimum cathodic protection potential by SSRT was -770 mV(SCE). At the applied cathodic protection potential of -770 mV -850 mV(SCE), the fracture morphology was dimple pattern with ductile fracture, while it was transgranular pattern (Q.C: quasi cleavage) under -875 mV(SCE).