• Restorative Dentistry and Endodontics
• /
• 제19권1호
• /
• pp.135-147
• /
• 1994

This study was conducted to evaluate whether the fatigue toughness of visible light cured composite resins could be improved and how much percentage of polymerzation shrinkage could be affected by additional heat treatment. 7 materials were investigated for this study: P-50, Lite-fil CR inlay, Pekafil, Clearfil CR inlay, Clearfil photo posterior, Z -100 and Progress. Diametral tensile strengths and linear shrinkages of composite resins were taken under visible light cured and additional post-cure heated condition and compared each other. A fatigue toughness of above materials was evaluated by measuring diametral tensile strength after they were repeatedly loaded with 120kgf/$cm^2$ up to 3000 cycles. The results obtained were as follows : 1. When composite resins were cured just by visible light, Lite fil CR inlay, Z -100 and Progress showed respectively higher diametral tensile strength than the other materials. Clearfil CR inlay, Clearfil photo posterior and Progress exhibited strong fatigue toughness compared to P-50 and Pekafil. 2. Post-cure heat treated composite resins had higher diametral tensile strengths than visible light cured composite resins at fatigue toughness test as well as no fatigue toughness test. 3. When Composite resins were additionally polymerized by post-cure heat treatment, P-50 showed weak fatigue toughness, on the contrary, Clearfil CR inlay, Z-100, Progress showed strong one. 4. When composite resins were cured just by visible light, percentage of polymerization linear shrinkage was the lowerest in Clearfil CR inlay, followed by, in ascending order, Clearfil photo posterior, Lite-fil CR inlay, Progress, Pekafil, P-50, and Z-100. In the case of post- cure heat treated composite resins, percentage of linear shrinkage was the lowest in Clearfil photo posterior, followed by, in ascending order, Lite-til CR inlay, Clearfil CR inlay, Progress, P-50, Pekafil and Z-100. 5. Percentage of polymerization linear shrinkage was greater in the post-cure heat treated composite resins than in the visible light cured composite resins and linear shrinkage increased significantly in Pekafil, Clearfil CR inlay, and Clearfil photo posterior between at the visible light cured and at the post-cure heat treated condition. The above results is saying that additional post-cure heat treatment on the composite resins for posterior restoration is able to affect on improvement of strength and fatigue toughness and lead to increase polymerization of composite resins.

• 열처리공학회지
• /
• 제10권3호
• /
• pp.165-171
• /
• 1997

Laser hardening for the piston ring groove of ductile cast iron was tried. Mechanical and microstructural investigation for the hardened area indicated that the laser heating technique could replace conventional induction hardening process completely and further showed that post grinding process would be eliminated by minimizing bulging of heat treated area. In laser hardening, the volume increase caused by martensitic phase transformation proved to be less than $10{\mu}m$, which insures no post machining on the hardened surface. As expected, the depth of hardening was inversely proportional to the beam scanning velocity and the highest surface hardness was obtained at the beam velocity of 0.75m/min. Heat treatment using phosphate coating demonstrated quite comparable result to the case of graphite suscepter.

• 한국화재소방학회:학술대회논문집
• /
• 한국화재소방학회 2008년도 춘계학술논문발표회 논문집
• /
• pp.7-10
• /
• 2008

Heat release characteristics of live fire load are an important parameter for performance oriented fire safety design of a building. While investigations have been carried out on the fire load and its burning behavior in office, residential and commercial buildings and so on, little effort has been paid for the rational treatment of fire load in post office buildings in Japan. In this report, burning behavior of typical combustible objects in post office buildings are studied by measuring heat release rates of plastic palettes with and without postal envelopes or packages and special containers loading numbers of palettes. The test results suggest that dynamic heat release rate is highly dependent on the condition of palettes especially if they load appropriate amount of postal envelopes or not.

• Journal of Advanced Marine Engineering and Technology
• /
• 제8권2호
• /
• pp.81-87
• /
• 1984

The effect of heat treatment and mechanical stress on the dielectic strength of epoxy resin film is studied. The film with 30-210 .mu.m thickness are casted at room temperature for 8 hours and post cured at the range of temperature 60-180 .deg. C, and the heat setting time are two kind, ie, 2 and 10 hours. The samples are made with Stycast 1266 that the primary compound is diglycidyl ether of bisphenol A, and the hardner is denaturated polyamines. Under no mechanical stresses, the maximum dielectric strength of the sample is obtained for the sample heat treated for 2 hours at 150 .deg. C. However, the best dielectric strength characteristics under compressive stress is obtained for the sample heat treated at 90 .deg. C and 120 .deg. C. The dielectric strength of the sample are also affected significantly by the cooling velocity of the sample after post heat setting at given temperature.

• Composites Research
• /
• 제26권2호
• /
• pp.123-128
• /
• 2013

PVDF(polyvinylidene fluoride) 섬유는 습식방사방법을 적용하여 제조하였다. PVDF 분자 내 압전 특성과 밀접한 관련을 갖는 ${\beta}$형태의 결정 함량을 높이기 위하여, 본 연구에서는 습식방사 된 섬유에 1단계 연신, 2단계 어닐링 공정으로 구성하여 후 처리를 도입하였다. 후 처리는 PVDF 고분자의 유리전이 온도($T_g$)와 용융온도($T_m$) 사이의 온도범위에서 진행하여, 최대의 ${\beta}$형태 결정을 생성 할 수 있는 열처리 조건을 최적화 하였다. 제조된 PVDF 섬유 내 분자 배향 특성과 결정 구조를 확인하기 위하여 적외선 분광 광도계(FT-IR)와 X선 회절 분석기(XRD)를 이용하여 분석하였으며, 전자현미경(SEM)을 통하여 섬유의 표면을 관찰하여 섬유의 평균직경을 확인하였다. 분석 결과, 후 처리 공정이 PVDF 결정 구조의 영향을 미치며, ${\beta}$형태의 결정 비율을 증가시킨다는 것을 확인하였다. 더불어 ${\beta}$형태 결정 향상으로 인해 기계적 강도가 증가되었으며, 압전 특성 향상까지 기대할 수 있었다.

• Journal of Welding and Joining
• /
• 제35권1호
• /
• pp.26-33
• /
• 2017

This study aims to investigate the suitability of requirement for post-weld heat treatment(PWHT) temperature when different P-No. materials are welded, which is defined by ASME Sec. III Code. For SA-516 Gr. 60 and SA-106 Gr. B carbon steels that are typical P-No. 1 material, simulated heat treatment were conducted for 8 h at $610^{\circ}C$, $650^{\circ}C$, $690^{\circ}C$, and $730^{\circ}C$, last two temperature falls in the temperature of PWHT for P-No. 5A low-alloy steels. Tensile and Charpy impact tests were performed for the heat-treated specimens, and then microstructure was analyzed by optical microscopy and scanning electron microscopy with energy-dispersive spectrometry. The Charpy impact properties deteriorated significantly mainly due to a large amount of cementite precipitation when the temperature of simulated heat treatment was $730^{\circ}C$. Therefore, when dissimilar metal welding is carried out for P-No. 1 carbon steel and different P-No. low alloy steel, the PWHT temperature should be carefully selected to avoid significant deterioration of impact properties for P-No. 1 carbon steel.

• 열처리공학회지
• /
• 제18권1호
• /
• pp.24-28
• /
• 2005

New post plasma nitriding can achieve a high uniformity that have been difficult in DC nitriding and have a high productivity comparable to gas nitriding. However, it has not a enough high nitriding potential for a rapid nitriding, because surface activation or ion etching in the general plasma nitriding cannot be expected. Thus, in this study, the effects of pre-treatments with oxidation and reduction gas have been investigated to improve the nitriding kinetics of post plasma nitriding. An effective pre-treatment consisting of oxidation and reduction resulted in the increase of surface energy of STD 11. This induced the surface hardness and the effective nitriding depth of STD 11. It is thought that the increase of the surface energy and the surface area with pre-treatment promote the nucleation of nitriding layer.

• Journal of Welding and Joining
• /
• 제19권1호
• /
• pp.65-74
• /
• 2001

A study on the corrosion behavior in case of As-welded and PWHT temperature 55$0^{\circ}C$ of welding part of RE36 steel for marine structure was investigated with parameters such as micro-Vickers hardness, corrosion potential measurement of weld metal(WM), base metal(BM) and heat affected zone(HAZ), both Al anode generating current and Al anode weight loss quantity under sacrificial anode cathodic protection conditions. And also we carried out slow strain rate test(SSRT) in order to research both limiting cathodic polarization potential for hydrogen embrittlement and optimum cathodic protection potential as well as mechanical properties by post-weld heat treatment(PWHT) effect. Hardness of HAZ was the highest among three parts(WM, BM and HAZ) and the highest galvanic corrosion susceptibility was HAZ. And the optimum cathodic polarization potential showing the best mechanical properties by SSRT method was from -770mV to -875mV(SCE). In analysis of SEM fractography, applied cathodic potential from -770mV to -875mV(SCE) it appeared dimple pattern with ductile fracture while it showed transgranular pattern (Q. C : quasicleavage) under -900mV(SCE). However it is suggested that limiting cathodic polarization potential indicating hydrogen embrittlement was under -900mV(SCE).

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.132-135
• /
• 2007

In this study, hydroformability and mechanical properties of pre- and post- heat treated Al6061 tubes at different extrusion type were investigated. For the investigation, as-extruded, full annealed and T6-treated Al6061 tubes at different extrusion type were prepared. To evaluate the hydroformability, uni-axial tensile test and free bulge test were performed at room temperature and $250^{\circ}C$. Also mechanical properties of hydroformed part at various pre- and post-heat treatments were estimated by tensile test. And the tensile test specimens were obtained from hexagonal prototype hydroformed tube at $250^{\circ}C$. As for the heat treatment, hydroformability of full annealed tube is 25% higher than that of extruded tube. The tensile strength and elongation were more than 330MPa and 12%, respectively, when hydroformed part was post-T6 treated after hydroforming of pre- full annealed tube. However, hydroformed part using T6 pre treated tube represents high strength and low elongation, 8%. Therefore, the T6 treatment after hydroforming for as-extruded tube is cost-effective. Hydroformability of Al6061 tube showed similar value for both extrusion types. But flow stress of seam tube showed $20{\sim}50MPa$ lower value.

• 한국작물학회지
• /
• 제10권
• /
• pp.45-50
• /
• 1971

방사선조사시 열처리의 효과를 알기 위하여 수도종자에 방사선조사시 열전후처리를 행하였던바$M_1$ 세대의 생물학적인 반응 및 $M_2$ 세대의 변이율에 대해 몇가지 결과를 얻었다. 1. 방사선선량 20kR에서 열전처리는 방사선단독조사에 비해 생물학적인 장해를 적게하고 변이율을 증가시켰다. 2. 방사선단독조사 및 조사전열처리에 비해 heat shocking으로서 열후처리하는 것은 변이율을 증가시켰다. 3. 열전처리에 의해 $M_1$ 세대의 장해가 적고 변이율이증가되는 가장 효과적인 열처리온도 및 시간은 6$0^{\circ}C$에서 30분간이었다. 4. 열처리는 방사선단독조사에 비해 mutation spectrum을 달리했다.