• Journal of the Korean Wood Science and Technology
• /
• v.46 no.5
• /
• pp.471-485
• /
• 2018

Post-heat treatment experiments were carried out for complete dimensional stabilization of thermally compressed wood (Pinus koraiensis). An absorption test was carried out to evaluate the dimensional stability. The specific gravity increased from 0.43 to 0.79 by thermal compression at a compression ratio of 50% thickness. Through the post-heat treatment of compressed wood, the water absorption and thickness swelling decreased with increasing the heat treatment temperature and time. In the case of the thickness recovery rate, when the heat treatment was performed for 24 hours at $120^{\circ}C$, $140^{\circ}C$ and $160^{\circ}C$, the thickness recovery was less than 1%. Therefore, it can be confirmed that the method of dimensional stabilization method of the thermal compression wood can be carried out very effectively through post heat treatment process.

• Journal of Powder Materials
• /
• v.12 no.2 s.49
• /
• pp.106-111
• /
• 2005

The effect of post-heat treatment on the coating characteristics and the fatigue strength of the gas flame thermally sprayed Stellite alloy coatings on $0.35\%$ carbon steel were investigated. The fatigue fracture surfaces of the heat treated samples were observed using SEM (Scanning Electron Microscopy). For as-sprayed samples, there was considerable scattering in the fatigue life due to the presence of the pores in the coating. After the post-heat treatment to improve the microstructural characteristics of the coating layer, the fatigue strength of the specimens was greatly improved, increasing with increasing the coating thickness. For the specimens with the 0.3mm and 0.5mm thick coating, the fatigue cracks originated in the substrate region just below the interface. On the contrary, for the specimens with the 1.0mm thick coating, they nucleated at the pore within the coating, and the fatigue strength was 2.6 times higher than that of the substrate due to the high fatigue resistance of the coating.

• Journal of the Korean Ceramic Society
• /
• v.35 no.7
• /
• pp.733-739
• /
• 1998

C-axis oriented zinc oxide thin films were deposited on Cornign 1737 glass substrate by an rf magnetron sputtering technique. The effects of deposition parameters and post heat-treatment on the crystallinity and electical properties of ZnO films were investigaed. As-deposited ZnO films showed the strong c-axis growth and excellent crystallinity under the deposition conditions as follows: substrate temperature 350$^{\circ}C$ ; growth and excellent crystallinity under the deposition conditions as follows ; substrate temperature 350$^{\circ}C$ rf power 75W ; gas pressure 6m Torr; percentage of oxygen 50% The higher heat-treating temperatue was the stronger c-axis growth and the better crystallinity of the deposited ZnO films were. The resistivity of ZnO films was significantly affected by deposition parameters and post heat-treatment. With increasing increased. After post heat-treating at 400$^{\circ}C$ in air the resistivity of ZnO films increased but post heat-treat-ing temperature 500$^{\circ}C$ rather diminished the film resistivity.

• Journal of Powder Materials
• /
• v.28 no.2
• /
• pp.134-142
• /
• 2021

In this study, AlSi10Mg powders with average diameters of 44 ㎛ are additively manufactured into bulk samples using a selective laser melting (SLM) process. Post-heat treatment to reduce residual stress in the as-synthesized sample is performed at different temperatures. From the results of a tensile test, as the heat-treatment temperature increases from 270 to 320℃, strength decreases while elongation significantly increases up to 13% at 320℃. The microstructures and tensile properties of the two heat-treated samples at 290 and 320℃, respectively, are characterized and compared to those of the as-synthesized samples. Interestingly, the Si-rich phases that network in the as-synthesized state are discontinuously separated, and the size of the particle-shaped Si phases becomes large and spherical as the heat-treatment temperature increases. Due to these morphological changes of Si-rich phases, the reduction in tensile strengths and increase in elongations, respectively, can be obtained by the post-heat treatment process. These results provide fundamental information for the practical applications of AlSi10Mg parts fabricated by SLM.

• Journal of the Korean Ceramic Society
• /
• v.38 no.4
• /
• pp.301-301
• /
• 2001

• Journal of the Korean Society for Heat Treatment
• /
• v.18 no.4
• /
• pp.223-228
• /
• 2005

Tube hydroforming provides a number of advantages over conventional stamping process, including fewer secondary operation, weight reduction, assembly simplification, adaptability to forming of complex structural components and improved structural strength and stiffness. It can produce wide range of products such as subframe, engine cradle, and exhaust manifold. In this study, the effect of the heat treatment conditions such as post seam annealing (PSA) and bright annealing (BA) on the ovality and hydro-formability of steel tubes has been investigated. Hydroformabilities have been estimated by the bulging heights obtained at various processing parameters such as internal pressure, axial feeding and heat treatment conditions. The ovality and forming height are strongly influenced by material properties after heat treatments.

• Journal of the Korean Society for Heat Treatment
• /
• v.22 no.5
• /
• pp.298-306
• /
• 2009

Gas nitriding and post oxidation were performed on stainless steels and SACM 645 steel. With increasing gas nitriding time, the increasing rate of nitrided layer was most rapid on SACM 645 steel and the nitriding depth of nitrided layer was most narrow on STS 304 steel among three steels. Corrosion resistance was increased with post oxidation on stainless steels and with increasing time the effect of corrosion resistance was decreased to compare with relatively short gas nitriding time. An improvement effect of corrosion resistance was consisted of predominantly on austenitic stainless steel by post oxidation after gas nitriding among three steels and it was relatively less influenced on martensitic stainless steel.

• Journal of the Korean Society for Heat Treatment
• /
• v.37 no.1
• /
• pp.9-15
• /
• 2024

Nd-Fe-B permanent magnets have been utilized on various industrial fields such as electric vehicles, generator, robots with actuator, etc, due to their outstanding magnetic properties even 10 times better than conventional magnets. Recently, there are many researches that report magnetic properties improved by controlling microstructure through adjusting alloying elements or conducting various processing. Especially, post-sintering annealing (PSA) can significantly improve the coercivity by modifying the distribution and morphology of Nd-rich phase which formed at grain boundaries. In this study, Nd-Fe-B sintered magnets were subjected to primary heat treatment followed by secondary heat treatment at 460℃, 500℃, and 540℃ to investigate the changes in microstructure and magnetic properties with the secondary heat treatment temperature. EBSD analysis was conducted to compare anisotropic characteristics. Through the SEM and TEM observation for analyzing the morphology and distribution of Nd-rich phase, we investigated the relationship between microstructure and magnetic properties of sintered Nd-Fe-B magnets.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.181-182
• /
• 2002

Most recent, Plasma ceramic spray is used on parts of tribosystem, has been investigated on the tribological performance. The application of ceramic coatings by plasma spray has become essential in tribosystems to produce better wear resistance and longer life in various conditions. The purpose of this work was to investigate the wear behavior of $8%Y_2O_3-ZrO_2$ coating due to temperatures of post-spay heat treatment. The plasma-sprayed $8%Y_2O_3--Zirconia$ coating was idiscussed to know the relationship between phase transformations and temperatures of post- spray heat treatment. Wear tests was carried out with ball on disk type on normal load of 50N, 70N and 90N under room temperature. The transformation of phase and the value of residual stress were measured by X-ray diffraction method(XRD). Tribological characteristics and wear mechanisms of coatings was observed by SEM. The tribologieal wear performance was discussed a point of view for residual stress. Consequently. post-spray heat treatment plays an important role in decreasing residual stress. Residual stress in coating system has a significant influence on the wear mechanism of coating.

• KSTLE International Journal
• /
• v.6 no.2
• /
• pp.45-50
• /
• 2005

Plasma ceramic spray that is applied on a machine part under severe work conditions has been investigated for tribological behavior. The application of ceramic coatings by plasma spray has become essential in tribosystems to produce wear resistance and long life in severe conditions. The purpose of this study was to investigate the wear characteristics of $8\%Y_{2}O_3-ZrO_2$ coating, in view of the effect of post-spay heat treatment. The plasma-sprayed $8\%Y_{2}O_3-ZrO_2$ coating was studied to know the relationship between phase transformations and wear behavior related to post-spray heat treatment. Wear test was carried out with ball on disk type on normal loads of 50N,70N and 90N under room temperature. The phase transformation of phase and the value of residual stress were measured by X-ray diffraction method(XRD). Tribological characteristics and wear mechanisms of coatings were observed by SEM. The tribological wear performance was discussed in the focusing of residual stress. Consequently, post-spray heat treatment plays an important role in decreasing residual stress. Residual stress in the coating system has a significant influence on the wear mechanism of coating.