• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.2
• /
• pp.49-59
• /
• 1993

A new signal processing technique is applied to four-cylinder spark and compression ignition engines for the diagnosis of power faults inside the cylinders. This technique utilizes two-sided directional power spectra(예S) of complex vibration signals measured from engine blocks as the patterns for engine cylinder power faults. The dPSs feature that they give not only the frequency contents but also the directivity of the engine block motion. For the automatic detection/diagnosis of cylinder power faults, pattern recognition method using multi-layer neural networks is employed. Experimental results show that the sucess rate for diagnosis of cylinder power faults using dPSs is higher than that using the conventional one-sided power spectra. The proposed technique is also tested to check the robustness to the sensor position and the engine rotational speed.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.73-74
• /
• 2012

본 논문은 점차 성장하고 있는 전동기를 이용한 교통수단으로써의 전기 자전거에 적용된 위치 센서인 홀 센서의 고장 검출을 위한 방법 제시와 고장 회피를 위한 방법을 제시한다. 전동기를 응용한 전기 자전거, 전기 스쿠터, 전기 자동차, 전기 보트 등 다양한 분야에서 전동기의 사용이 점차 넓어지고 있지만 현재는 전동기의 구동 및 제어의 관점에서만 다루어 지고 있는 실정이다. 하지만 전동기의 구동 보다 더 중요한 문제는 사람을 운송하는 분야이기 때문에 높은 구동 안정성이 요구 되고 있다. 따라서 본 논문은 전기 자전거에 적용된 홀 센서의 고장의 종류에 대해 검토하고 고장으로 판단 한 이후 정상적인 구동이 가능 할 수 있도록 센서리스 구동으로의 전환이 가능 하도록 하였다. 이를 모의 실험과 실험을 통해 타당성을 검증 하고자 한다.

• Proceedings of the Korea Society of Information Technology Applications Conference
• /
• 2005.11a
• /
• pp.147-151
• /
• 2005

CAN(Controller Area Network) is a simple and efficient network system for real time control and measurement. As it is not only good at error detection but also strong in electromagnetic interference, CAN has been widely used all over the industries. Basically, CAN needs a master node in charge of sensor data collection, node scheduling for data transmission to a monitoring system and error detection. According to the number of mater nodes, the CAN system is classified into two type of master system. One is a single master system that has only one master node and the other is a multi-master system where any sensor node can become a master node depending on the system's conditions. While it has the advantage of its fault tolerance, the multi-master system will suffer form the overall performance degradation when a defect is found in the master node. It is because all sensor nodes pertaining to a defective master node lose their position. Moreover, it is difficult and expensive to implement. For a single master system, the whole system will be broken down when a problem happens to a single master. In this paper, a dynamic master system is presented that there are several sub-master nodes of which basic functions are those of other sensor nodes at ordinary times but dynamically changed to replace the failing master node. An effective scheduling algorithm is also proposed to choose an appropriate node among sub-master nodes, where each sub-master node has its precedence value. The performance of the dynamic master system is experimented and analyzed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.1
• /
• pp.46-50
• /
• 2015

The cable degradation process is largely divided into three steps; Step 1 : Thermal degradation, Step 2 : Weibull degradation, Step 3 : Partial discharge. it is progress in step order. This article aims to explain the process of cable degradation using the method of insulation resistance and accordingly to compose and manufacture a system of measuring the life of electrical cable. Before measuring the insulation resistance, a system of measuring the temperature and current of cables was made, and the established system was installed for test on the site of a power plant to collect the measured data. The current sensor was used TFC30P80A-CL420, and temperature sensor was used the DK-1270 PT100 sensor as RTD sensor. When measured the temperature and the load current at the same position, was confirmed that in case of the load current value was high, also temperature value high. Therefore, the correlation between load currents and temperature was verified, and the analysis of diagnostic data was evaluated, which could be utilized in identifying the fault condition of cable systems.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.2
• /
• pp.156-165
• /
• 2009

Threat due to malfunction of space launch vehicles is significant since it is bigger and flights longer range than military missiles or scientific rockets. It is necessary to implement a flight safety system to minimize the possible hazard. Design objective of the tracking filter for the flight safety system is different from conventional tracking filters since estimation reliability is more emphasized than estimation accuracy. In this paper, a fusion tracking filter was implemented for processing multi-sensor data from a space launch vehicle. The filter performance is evaluated by analyzing the error of the estimated position and instantaneous impact point. Also a fault detection algorithm is implemented to guarantee fusion filter's reliability under any sensor failure and verified to maintain stability successfully.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.148-154
• /
• 2005

As the exciting point of each phase is determined by the position of rotor, the rotor's accurate position-information is needed for the Switched Reluctance Motor(SRM). When using an absolute-encoder or a resolver, to detect the location of rotor the initial starting is possible, as early sensing of rotor's location is possible. However, this is not appropriate, considering the economical efficiency, and in case of using the incremental-encoder, there's a problem at initial starting as it is not easy to track down the location of rotor at the very beginning. When using Hall-ICs, there's a fault, as it needs a special ring magnet. Considering the initial starting and economical efficiency, the optical sensor technique using a slotted-disk and an opto-interrupter is appropriate, however, this method needs three opto-interrupters and a slotted-disk when using the 6/4 pole SRM. Nevertheless, in this paper, it used only two optical sensors to operate 6/4 pole SRM and made the start up and also forward and reverse operation possible. By excluding the slotted-disc md shortening a optical sensor, it improved the convenience and economical efficiency of the production. Also, as the space for slotted-disc is no more needed, it was able to reduce the size of motor.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.11
• /
• pp.2446-2452
• /
• 2012

In order to meet the recently enhanced emission standards at home and abroad, it is necessary to develop the CRDI ECU control algorithm that users can adjust fuel injection timing and amount in response to their needs. Therefore, this study developed the simulator for knocking analysis that enables knocking discrimination and engine balance correction applicable to the ECU exclusive to the industrial CRDI engine. The purpose of this study is to provide the driver-oriented diagnostic service that enable drivers to diagnose vehicles directly by developing diagnostic devices for vehicles with ths use of the results of the developed simulator for knocing analysis according to the OBD-II standards. For this purpose, this study aims to improve the fuel efficiency of vehicles by proposing the S/W design method of the OBD-II diagnosis device that can provide real-time communcations with the use of wired system and bluetooth module as a wireless system to send and recevice automobile fault diagnosis signal and sensor output signal, and to suggest an improvement for engine efficiency by minimizing the generation of harmful exhaust gas.