• Proceedings of the KIEE Conference
• /
• 2004.04a
• /
• pp.147-149
• /
• 2004

This paper presents a new velocity estimation strategy of a non-salient permanent magnet synchronous motor(PMSM) drive without high frequency signal injection or special PWM pattern. This approach is based on the d-axis current regulator output voltage of the drive system which has the information of rotor position error. The rotor velocity can be estimated through a rotor position tracking PI controller that controls the position error to zero. For zero and low speed operation, the PI gains of rotor position tracking controller have a variable structure. The PI tuning formulas are derived by analyzing this control system using the frequency domain specifications such as phase margin and bandwidth assignment.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.94.2-94
• /
• 2002

$\textbullet$ The method to have real-time response at the motion control. $\textbullet$ The trajectory generation method guarantees the continuous acceleration in changing the velocity during the actuator is moving. $\textbullet$ We propose the velocity profile generation algorithm in order to change object position or object velocity with continuous acceleration using blending method.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.342-345
• /
• 1995

This paper describes the design process and the experimental results of a fuzzy logic controller to control the tip position of a fixible-link manipulator, directly driven by a AC motor, with a large payload. The joint angle fuzzy logic controller is designed without a costly nonlinear system analysis of the flexible manipulator and the AC motor drive system. The state variables for the fuzzy logic controller are joint angle, joint velocity, link deflection, and link deflection velocity. The simulation and experimental results show that the joint position control is not satisfactory when the controller is designed under the assumption of no link flexibility and that stable joint position control and link vibration suppression can be cahieved with the fuzzy logic controller suggested in this paper.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.566-569
• /
• 2000

This hybrid position/force control for the dynamic walking of the biped robot is performed in this paper. After the biped robot was modeled with 14 degrees of freedom of the multibody dynamics, the equations of motion are constructed using velocity transformation technique. Then the inverse dynamic analysis is performed for determining the driving torques and the ground reaction forces. From this analysis, obtains the maximum ground contact force at the moment of contacting which act on the rear of the sole of swing leg and the distribution curve of the ground reaction. Because these maximum force and distribution type acts an important role to the stability of the whole dynamic walking, they are reduced and distributed smoothly by means of the trajectory of the modified ground reaction force. This new trajectory is used to the reference input for more stable dynamic walking of the whole walking region.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.219-222
• /
• 1994

This thesis describes an observer of Switched Reluctance Motor for position. velocity and torque estimation using current sening. Inductance of SRM varies trapezoidally with respect to the rotor position. This means that the inductance of each phase is a periodic function with the same period. Under this condition. the observer with a constant gain can be developed though SRM has nonlinear characteristics. Because SRM has equivalent physical meaning with each period. The stability of error system which is the difference between actual system and observer system. is analyzed using Lyapunov and variable structure theory. The effectiveness of the proposed estimation is shown by various simulation.

• ICROS
• /
• v.5 no.2
• /
• pp.29-34
• /
• 1999

• Journal of Institute of Control, Robotics and Systems
• /
• v.11 no.11
• /
• pp.930-935
• /
• 2005

In this paper, position tracking control of an autonomous helicopter is presented. Combining an LQR method and a proportional control forms a simple PD control. Since LQR control gains are set for the velocity control of the helicopter, a position tracking error occurs. To minimize a position tracking error, neural network is introduced. Specially, in the frame of the reference compensation technique for teaming neural network compensator, a position tracking error of an autonomous helicopter can be compensated by neural network installed in the remotely located ground station. Considering time delay between an auto-helicopter and the ground station, simulation studies have been conducted. Simulation results show that the LQR with neural network performs better than that of LQR itself.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.108.4-108
• /
• 2001

The integrated environment for the fuzzy logic controller with the acceleration converter to improve the dynamic characteristic of a one-axis moving table is proposed in the paper. The two inputs of the fuzzy logic controller are position error and velocity. The two inputs of the acceleration converter used to produce the acceleration input for the one-axis moving table are actual and setting rotational speeds. The proposed controller is implemented on a personal computer by using MATLAB and Visual Basic for a real time control via a motion control board. The position control results when the stair input is applied to control the position of the one-axis moving table, are shown. The experimental results of the proposed position control system are compared to the conventional PID ...

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.11
• /
• pp.1095-1101
• /
• 2006

The clean tube system was developed as a means of transferring air-floated wafers inside a closed tube filled with super clean air. This paper presents a wafer position sensing method in the clean tube system, where the photo proximity sensors are used. The first presented method uses the two positions sensed lately in order to compute the wafer center position. The next method uses the latest sensed position and the next latest position compensated with the information of the wafer velocity. The third method uses the kalman filter, which enable us to use all the previous sensing information. The simulation results are compared to show results of the presented method. In addition, the paper presents a control method to stop the wafer at the center of the unit in the clean tube system. The experimental clean tube system worked successfully with the applying the both presented methods of sensing and control.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.121-126
• /
• 2000

This research proposes a new advanced control method and demonstrates its realization in part. By incorporating shape machining and cutting force control at a time, this integrated scheme makes it possible to machine a desired shape and avoid the trouble of programming feedrate and spindle speed before machining and also reduce the shape error. The main idea proposed to achieve those goals consists in giving commanded path and desired cutting force at the same time. which makes it possible for position and force controller to distribute the corresponding velocity of individual axes and main spindle by an appropriate interpolation. That indicates we can replace the built-in interpolator of commercial machine tools by the developed algorithm.