• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.11
• /
• pp.2391-2396
• /
• 2010

The power-controlled six-port element that can control the local oscillator signal power and receiving RF signal power was designed and implemented in this paper. The direct conversion six-port element configuration was proposed, which provides the constant six-port output power by controlling the six-port input power with various signal strength. The direct conversion six-port element protects the power detector element of six-port receiver from the saturation status and compensates the transmission performance degradation. For implementation of power-controlled six-port element, the power-controlled six-port element including the power controller was analyzed. The implemented power-controlled six-port element shows the power control capability of 36 dB and gain imbalance of about 1.6 dB, phase imbalance of about $4^{\circ}$ in the frequency range of 1.69 GHz. The measured results show the good performance as direct conversion front-end element.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.27 no.6
• /
• pp.300-306
• /
• 2015

For an asymmetric scroll compressor for heat pump application, a numerical simulation was carried out to investigate the effects of injection port design on the compressor's performance under gas injection. To validate the simulation, the numerical results were compared with experimental results obtained from a scroll compressor with a base injection port design. There was good agreement between simulation and experimental results, with around a 1% difference in the injection mass flow rate when the injection pressure was below $12kgf/cm^2A$ for the heating mode. Various injection port angular positions were numerically tested to yield better injection performance. The largest improvement in heating capacity was obtained at angles of $240^{\circ}$ and $200^{\circ}$ inward from the scroll wrap end angle for low-temperature and standard heating conditions, respectively, while the maximum COP improvement was at $365^{\circ}$ and $280^{\circ}$, respectively. A considerable improvement in cooling capacity was also found at the injection port angle of $240^{\circ}$.

• Journal of Navigation and Port Research
• /
• v.31 no.8
• /
• pp.725-731
• /
• 2007

This paper aims to analyze an action about a port choice of shipper between two ports. For this propose, this paper analyzed a port choice action for Kwangyang and Busan port using a fuzzy logic and neural network. Also, this paper compared classification performance of fuzzy-neural network to Logit model, and analyzed a port choice action into change Para-meta such as freight volumes and service standard.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.256-259
• /
• 2007

In this paper, the combustion characteristics of hybrid rocket were studied with various port number of the cylindrical multi-port grain. For the regression rate case, as the port number increases, the both port regression rate and end-surface regression rate tend to increase. For the performance parameter case, as the port number increases, the O/F ratio tends to decreases and the specific impulse tends to increase.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.11
• /
• pp.3021-3031
• /
• 1994

Experiments have been performed to find out the effect of the mixing port length of Y-jet atomizers on the spray performance, using air and water as the test fluids. Water and air flow rates and drop sizes were measured at each injection pressure condition for different mixing port length. The air flow rate was almost unaffected by the change of the mixing port length. However, the water flow rate was relatively susceptible to the change of the mixing port length. The mixing point pressure was very much influenced by the mixing port length. Variations of spatial distribution of Sauter Mean Diameter (SMD, $D_{32}$) and the cross-section-averaged SMD ($D_{32,m}$) with different mixing port length and air/water mass flow rate ratio were examined. Generally, when the mixing port length was reduced, the mean drop size decreased and became spatially even.

• Journal of Korea Port Economic Association
• /
• v.19 no.2
• /
• pp.87-109
• /
• 2003

Localization is one of the typical phenomena of this age in Korea. Localization of Port is on the beginning in this Country as the introduction of Port Authority in the Port of Busan and Incheon. As the condition of world trade has been changed, the level of Competition among Ports is severer than before, especially in the East Asia Area. Since many experts of Port say that centralized control system of Port has many Problems, some other Port Control system has been studied and suggested for long time. One of the Countermeasures of these Port Problems is Port Authority System which aims the balance of central and local development. Port Authority System does not want to achieve only Public Duty or Utility but also Commerciality which is fundamentally very important for the survival of Port. In this Paper, the necessities of Port Authority Introduction in Korea was explained. And Port Authority System will be introduced 2004 year in Busan Port firstly and Incheon Port, secondly. The Main Contents of Port Authority System was suggested , in this Paper and some Problems which shall be considered for better operation of Port Authority System was investigated. I suggested some countermeasures, endeavoring the competitive advantage of Port and higher Port Performance, in terms of 3 Dimensions. One is in the side of basic Policy Directions, the other is the activation schemes of functional department which composed of many activities of Port Authority System and the third is in the side of operation body. As this paper, however, has some limitations and Port Authority System is just beginning stage, future research shall be continued in real and concrete level.

• Journal of the Korea Safety Management & Science
• /
• v.13 no.2
• /
• pp.203-210
• /
• 2011

Incheon Port has been served as not only the center of the Yellow Sea and port for trade with China but also domestic gateway port for the metropolitan area, playing a professional role as the greatest domestic Port which processes a variety of items such as imported raw materials, bulk cargo, oil and gas and so on. This study was conducted based on step by step business process between port entry and departure of ship, and incurred cost according to port industry classification and performance on the port facility. Bulk cargo and general cargo such as grain, food, steel, scrap metal, wood, coal, LNG, LPG and oil etc., which have a vast majority of import goods, have been treated by 57,062 thousand tons and 7,409 thousand tons of container cargo were processed at Incheon Port in 2009. Bulk vessels and carriers moving items such as LPG, LNG and oil recorded 38,836 thousand won and full-container vessels recorded 11,001 thousand won as the amount of notified port facility usage fees in 2008.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.5
• /
• pp.188-196
• /
• 1997

Many researchers have developed the measurement technique of in-cylinder flow characteristics and found the effect of intake port geometries on engine performance. The flow characteristics of four-valve cylinder head were examined in a steady flow rig for different intake ports. Tumble intensity of intake configurations with different entry angles were quantified with a tumble meter. The velocity and angular momentum distributions in the tumble adaptor were measured under steady conditions with PIV(Particle Image Velocimetry). We have obtained the results that flow structure becomes complicated by valve interference at low valve lift. As the valve interferences were reducing and the flow pattern changed to large vortex structure with tumble direction, intake ports with different entry angles have different tumble centers. Tumble eccentricity of intake port with low entry angle was large, so that the port had relatively much angular momentum compared to others which was expected to improve combustion performance.

• Journal of Information Technology Services
• /
• v.11 no.3
• /
• pp.1-16
• /
• 2012

This paper is aimed to present a fuzzy decision-making approach to deal with disaster recovery priority decision problem in information system. We derive an evaluation approach based on TOPSIS(Technique for Order Performance by Similarity to Ideal Solution), to help disaster recovery priority decision of total information system for port logistics in a fuzzy environment where the vagueness and subjectivity are handled with linguistic terms parameterized by trapezoidal fuzzy numbers. This study applies the fuzzy multi-criteria decision-making method to determine the importance weight of evaluation criteria and to synthesize the ratings of candidate disaster recovery system. Aggregated the evaluators' attitude toward preference, then TOPSIS is employed to obtain a crisp overall performance value for each alternative to make a final decision. This approach is demonstrated with a real case study involving 4 evaluation criteria(system dependence, RTO, loss, alternative business support), 7 information systems for port logistics assessed by 5 evaluators from Maritime Affairs and Port Office.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 1997.04a
• /
• pp.5-16
• /
• 1997

This paper presented a method of evaluting navigational safety of a ship by means of the integrated seakeeping performance index(ISPI). The ISPI is defined by measuring only any one factor through the medium of relative dangerousness of the other factors for evaluating seakeeping performance. This evaluation method can be applied to the ships for any types and loading conditions. In developing the practical evaluation system of navigational safety. it is expected to be useful for developing the optimum type of ship by applying at the initial design phase.