• Journal of the Optical Society of Korea
• /
• v.17 no.5
• /
• pp.423-427
• /
• 2013

We present the preparation and characteristics of liquid-phase sensors based on nano-porous silicon multilayer structures for determination of organic content in gasoline. The principle of the sensor is a determination of the cavity-resonant wavelength shift caused by refractive index change of the nano-porous silicon multilayer cavity due to the interaction with liquids. We use the transfer matrix method (TMM) for the design and prediction of characteristics of microcavity sensors based on nano-porous silicon multilayer structures. The preparation process of the nano-porous silicon microcavity is based on electrochemical etching of single-crystal silicon substrates, which can exactly control the porosity and thickness of the porous silicon layers. The basic characteristics of sensors obtained by experimental measurements of the different liquids with known refractive indices are in good agreement with simulation calculations. The reversibility of liquid-phase sensors is confirmed by fast complete evaporation of organic solvents using a low vacuum pump. The nano-porous silicon microcavity sensors can be used to determine different kinds of organic fuel mixtures such as bio-fuel (E5), A92 added ethanol and methanol of different concentrations up to 15%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05b
• /
• pp.25-28
• /
• 2000

A capacitance-type humidity sensors in which porous silicon layer is used as humidity-sensing material was developed. This sensors was fabricated monolithically to be compatible with the typical IC process technology except for the formation of porous silicon layer. As the sensors is made as a mesa structure, the correct measurement of capacitance is expected because it can remove the effect of the parasitic capacitance from the bottom layer and another junctions. To do this, the sensor was fabricated using process steps such as localized formation of porous silicon, oxidation of porous silicon layer and etching of oxidized porous silicon layer. From completed sensors, capacitance response was measured on the relative humidity of 25 to 95% at room temperature. As the result the measured capacitance showed the increase over 300% at the low frequency of 120Hz, and showed little dependence on the temperature between 10 to $40^{\circ}C$.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.1014-1016
• /
• 1998

A capacitance-type humidity sensor using porous silicon layer is developed. The unique property of this sensor is a structure which has electrodes on the surface of the wafer like a general IC device. To do this. the sensor was fabricated using process such as localized formation of porous silicon, oxidation of porous silicon layer, and etching of oxidized porous silicon layer. The measurement of humidity-sensing ability was done for two type of sensors using porous silicon layer formed in 25 and 35% HF solutions, respectively. As the result, the former sensors showed larger value and variation of capacitance for the relative humidity.

• Journal of Sensor Science and Technology
• /
• v.15 no.6
• /
• pp.457-461
• /
• 2006

To use the porous silicon as gas sensors, we made the MOPS structure from the porous silicon with Al evaporation and investigated the sensing characteristic of ethanol. When the MOPS structure is in contact with ethanol gas, the maximum peak of PL changes and it return to original intensity without contact. The MOPS structure had response time 0.78s and recovery time 4.13s when it is in contact with ethanol, which satisfied the required sensor standards. Further complimentary researches, however, are required to investigate the contact mechanism between MOPS structure and ethanol and to solve the surface contamination problem.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.1
• /
• pp.93-99
• /
• 1996

The formation properties and oxidation mechanism of electrochemically oxidized porous silicon(OPS) films have been studied. To examine the humidity-sensitive properties of OPS films, surface-type and bulk-type humidity sensors were fabricated. The oxidized thickness of porous silicon layer(PSL) increases with the charge supplied during electrochemical humidity sensor shows high sensitivity at high relative humidity in low temperature. The sensitivity and linearity can be improved by optimizing a porosity of PSL. (author). refs., figs.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.1085-1088
• /
• 2003

In this work, we fabricated a gas-sensing device based on porous silicon(PS), and its I-V and C-V properties were investigated for sensing alcohol vapor. The structure of the sensor consists of thin Au/Oxidized porous silicon/porous silicon/Silicon/Al, where the silicon substrate is etched anisotropically to be prepared into a membrane shape. As the result, I-V curves showed typical tunneling property, and C-V curves were shaped like those of a MIS (metal-insulator- semiconductor) capacitor, where the capacitance in accumulation was increased with alcohol vapor concentration.

• Journal of the Korean Electrochemical Society
• /
• v.2 no.1
• /
• pp.17-22
• /
• 1999

Since the use of porous silicon for microsensors and microactuators is in the euly stage of study, only several application devices, such as light-emitting diodes and chemical sensors have so far been demonstrated. In this paper we present an overview of the present status of porous silicon sensors and actuators research with special emphasis on the applications of chemical sensors and optical devices. The capacitive type porous silicon humidity sensors had a nonlinear capacitance-humidity characteristic and a good sensitivity at higher humidity above $40\%RH$. The porous silicon $n^+-p-n^+$ device showed a sharp increase in current when exposed to an ethanol vapor. The $p^+-PSi-n^+$ diode fabricated on porous silicon diaphragm exhibited an optical switching characteristic, opening up its utility as an optical sensor or switch. The photoluminescence (PL) spectrum, taken from porous silicon under 365 nm excitation, had a broad emission, peaked at -610 nm. The electroluminescence(EL) from ITO/PSi/In LED had a broader spectrum with a blue shifted peak at around 535nm than that of the PL.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.792-796
• /
• 2002

In this work, porous silicon(PS) layer is used as a sensing material to detect organic gases. To do this, PS sensors with membrane structure are fabricated. The sensors were made by applying the technologies of membrane formation by anisotropic etching of silicon, and PS layer formation by anodization in HF solution. From fabricated sensors, current-voltage (I-V) curves were measured against ethanol (called alcohol), methanol and acetone gases evaporated from 0.1 to 0.5% solution concentrations at $36^{\circ}C$. As the result, all curves showed rectifying behavior due to a diode structure between Si and PS, and the conductance of sensor devices increased largely with the organic solution concentration at high voltage of 5V.

• Journal of Integrative Natural Science
• /
• v.3 no.3
• /
• pp.168-173
• /
• 2010

Novel porous silicon chip exhibiting dual optical properties, both Frbry-Perot fringe (optical reflectivity) and photoluminescence had been developed and used as chemical sensors. Porous silicon samples were prepared by an electrochemical etch of p-type sillicon wafer (boron-doped, <100> orientation, resistivity 1 - 10 ${\Omega}$). The ething solution was prepared by adding an equal volume of pure ethanol to an aqueous solution of HF (48% by weight). The porous silicon was illuminated with a 300 W tungsten lamp for the duration of etch. Ething was carried out as a two-electrode Kithley 2420 preocedure at an anodic current. The surface of porous silicon was characterized by FT-IR instrument. The porosity of samples was about 80%. Three different types of porous silicon, fresh porous silicon (Si-H termianated), oxidized porous silicon (Si-OH terminated), and surface-derivatized porous silicon (Si-R terminated), were prepared by the thermal oxidation and hydrosilylation. Then the samples were exposed to the wapor of various organics vapors. such as chloroform, hexane, methanol, benzene, isopropanol, and toluene. Both reflectivity and photoluminescence were simultaneously measured under the exposure of organic wapors.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.11
• /
• pp.963-968
• /
• 2002

In this work, porous silicon (PS) layer is investigated as a sensing material to detect organic vapors such as ethanol (called alcohol), methanol, and acetone in low concentrations. To do this, PS sensors were fabricated. They have a membrane structure and comb-type electrodes were used to detect the change of electrical resistance effectively. PS layer on Si substrates was formed by anodization in HF solution of 25%. From fabricated sensors, current-voltage (Ⅰ-Ⅴ) curves were measured for gases evaporated from 0.1 to 0.5% organic solution concentrations at 36$\^{C}$. As the result, all curves showed rectifying behavior due to a diode structure between Si and the PS layer. The conductance of most sensors increased largely at high voltage of 5V, but the built-in potential on the measured Ⅰ-Ⅴ curve was lowered inversely by the adsorption effect of the organic vapors with high dipole moment.