• Journal of Powder Materials
• /
• v.22 no.5
• /
• pp.362-366
• /
• 2015

The effect of sublimable vehicle composition in the camphor-naphthalene system on the pore structure of porous Cu-Ni alloy is investigated. The CuO-NiO mixed slurries with hypoeutectic, eutectic and hypereutectic compositions are frozen into a mold at $-25^{\circ}C$. Pores are generated by sublimation of the vehicles at room temperature. After hydrogen reduction at $300^{\circ}C$ and sintering at $850^{\circ}C$ for 1 h, the green body of CuO-NiO is completely converted to porous Cu-Ni alloy with various pore structures. The sintered samples show large pores which are aligned parallel to the sublimable vehicle growth direction. The pore size and porosity decrease with increase in powder content due to the degree of powder rearrangement in slurry. In the hypoeutectic composition slurry, small pores with dendritic morphology are observed in the sintered Cu-Ni, whereas the specimen of hypereutectic composition shows pore structure of plate shape. The change of pore structure is explained by growth behavior of primary camphor and naphthalene crystals during solidification of camphor-naphthalene alloys.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2004.10a
• /
• pp.90.3-90.3
• /
• 2004

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.177.1-177
• /
• 2003

• Journal of the Korean Ceramic Society
• /
• v.33 no.12
• /
• pp.1394-1402
• /
• 1996

The Silica gel with the density of 0.2g/cm3 and porosity of 90% was synthesized. The silica wet gel was dried and heat-treated under the ambient pressure after modification of the wet gel surface by TMCS. Specific surface area total pore volume and mean pore radius of dried gel were all increased with increasing heat treatment temperature and confirmed about 1400m2/g, 4.5cc/g and 8 nm respectively after heat treatment above 25$0^{\circ}C$. But the pore size distribution of dried gel was in the range of 1-100nm and was almost indepen-dent of temperature. As the result of external shape pore characteristics and microstructure of gel using SEM similar properties were observed between the silica gel synthesized in this study and the silica aerogel through the super critical drying.

• The Korean Journal of Ceramics
• /
• v.6 no.3
• /
• pp.209-213
• /
• 2000

Microstructural changes of AlOOH doped UO$_2$pellet after annealing up to 216h have been observed and they were compared with those of the standard pellet. Grain and pore size of UO$_2$pellet increased with the addition of AlOOH and its effect was still validated during annealing. Densification rate was reduced by the addition of AlOOH and it was attributed to coarsened pores with spherical shape. Grain and pore growth was stopped and density increase was the least after 144h of annealing. The variation of pore size resulting from annealing has a linear relationship with that of grain size.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.3
• /
• pp.368-375
• /
• 1987

Effective thermal conductivity of the porous nuclear fuel has been investigated numerically. Difficulties associated with irregular shape of pore have been overcome by using the Body Fitted Coordinate Systems. A computer code has been developed to solve the governing equation with appropriate boundary conditions by transforming from the Cartesian coordinates to the nonorthogonal curvilinear coordinates. The effects of the porosity have been investigated. For a convenient use of the result, a correlation equation was suggested under the assumption of circular pore. The computation results by the assumption of randomly oriented elliptic pore has been agreed more closely to existing experimental result than that by the assumption of circular pore.

• Journal of Powder Materials
• /
• v.21 no.5
• /
• pp.366-370
• /
• 2014

The present study demonstrates the effect of solidification condition on the pore structure in freeze drying process using the slurries of CuO/sublimable vehicles. Camphene and Camphor-45 wt% naphthalene based slurries with 14 vol% CuO powder were frozen into a mold at $-25^{\circ}C$, followed by sublimation at room temperature. The green bodies were hydrogen-reduced and sintered at $500^{\circ}C$ for 1 h. The porous Cu specimen, frozen the CuO/camphene slurry into the heated mold of the upper part, showed large pores with unidirectional pore channels and small pores in their internal wall. Also, it was observed that the size of large pores was decreasing near the bottom part of specimen. The change of pore structure depending on the freezing condition was explained by the nucleation behavior of camphene crystals and rearrangement of solid powders during solidification. In case of porous Cu prepared from CuO/Camphor-naphthalene system, the pore structure exhibited plate shape as a replica of the original structure of crystallized vehicles with hypereutectic composition.

• Journal of the Korean Ceramic Society
• /
• v.46 no.5
• /
• pp.534-539
• /
• 2009

Reaction Bonded Silicon Carbide(RBSC) has been used for engineering ceramics due to low-temperature fabrication and near-net shape products with excellent structural properties such as thermal shock resistance, corrosion resistance and mechanical strength. Recently, attempts have been made to develop hot gas filter with gradient pore structure by RBSC to overcome weakness of commercial clay-bonded SiC filter such as low fracture toughness and low reliability. In this study a fabrication process of porous RBSC with multi-layer pore structure with gradient pore size was developed. The support layer of the RBSC with multi-layer pore structure was fabricated by conventional Si infiltration process. The intermediate and filter layers consisted of phenolic resin and fine SiC powder were prepared by dip-coating of the support RBSC in slurry of SiC and phenol resin. The temperature of $1550^{\circ}C$ to make Si left in RBSC support layer infiltrate into dip-coated layer to produce SiC by reacting with pyro-carbon from phenol resin.

• Journal of the Korean Ceramic Society
• /
• v.25 no.3
• /
• pp.217-224
• /
• 1988

Pore structures of Alkoxide-derived aluminas are investigated by BET Nitrogen Sorption method. Aluminas are derived from hydrolysis of aluminum isopropoxide at 3$^{\circ}$and 8$0^{\circ}C$ with stoichiometric quantities of water in use. The resulting hydrolysates are then subjected to thermal treatment for a fixed period of time from 200$^{\circ}$to 50$0^{\circ}C$ in gradual fashions. The hydrolysates obtained at 3$^{\circ}C$ increase their pore volumes with increasing heat treatment, exhibiting their pore-size distributio as twinpeaked. In contrast, the reverse is true to the hydrolysates obtained at 8$0^{\circ}C$, showing their pore size distribution as single-peaked. This suggests that the pore shapes of the former shall be slit-shaped, whilst whose as the latter shall be of a ink-bottle shape. All the evidence indicates that the hydrolytic temperatures play an important role not only in determining the pore shapes of the alumina samples, but in controlling the liberation of structural water in the alumina layers. It is also, surmized that the subsequent heat treatment may at best affect the mode of pore size distribution for the resulting alumina product(s).

• Journal of Powder Materials
• /
• v.18 no.6
• /
• pp.488-495
• /
• 2011

This study was performed to fabricate the porous titanium foam by space holder method using NaCl powder, and to evaluate the effect of NaCl volume fractions (33.3~66.6 vol.%) on the porosities, compressive strength, Young's modulus and permeability. For controlling pore size, CP titanium and NaCl particles were sieved to different size range of 70~150 ${\mu}m$ and 300~425 ${\mu}m$ respectively. NaCl of green Ti compact was removed in water followed by sintered at $1200^{\circ}C$ for 2 hours. Total porosities of titanium foam were in the range of 38-70%. Pore shape was a regular hexahedron similar that of NaCl shape. Porous Ti body showed that Young's modulus and compressive strength were in the range of 0.6-6 GPa and 8-127 MPa respectively. It showed that pore size and mechanical properties of Ti foams was controllable by NaCl size and volume fractions.