• 한국지반공학회논문집
• /
• 제19권4호
• /
• pp.7-14
• /
• 2003

본 연구는 등방성 투수계수를 갖는 점토에 설치된 압밀촉진 케이슨에 관한 선행 연구를 보다 발전시켜서 비등방성 투수계수를 갖는 점토에서의 압밀촉진 케이슨 기초공법의 타당성을 이론적으로 검증하였다. 투수계수의 비등방성을 고려한 2차원 투수 압밀 방정식의 과잉간극수압에 대한 해석해와 시간계수에 따른 평균압밀도 식을 유도하였다. 비등방성 투수계수비가 5, 10, 50인 경우, $\xi$=0.1인 단면에서 평균압밀도 90%에 도달하는 시간은 기존 케이슨에 비해 각각 약 8배, 13배, 47배 단축되었다. 이는 지반의 비등방성 투수계수비가 클수록 압밀촉진 케이슨 기초공법이 압밀에 소요되는 시간을 단축시키는데 효과적임을 의미한다. 또한 본 연구에서는 해석단면의 깊이에 대한 폭의 비 및 비등방성 투수계수비에 따른 전체 해석단면에서의 평균압밀도에 대한 그래프를 제시하였으며, 이를 이용하여 평균압밀침하량을 쉽게 산정할 수 있다.

• Journal of Electrochemical Science and Technology
• /
• 제1권1호
• /
• pp.50-56
• /
• 2010

$La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_{3-\delta}$ (LSCF) powders with different particle sizes, synthesized through a citrate complexation method and a gel-casting technique, are used to fabricate porous LSCF cathodes with graded microstructures via tape casting. To create porous electrodes with desired porosity and pore structures, graphite and starch are used as pore former for different layers of the graded cathode. Examination of the microstructures of the as-prepared LSCF cathode using an SEM revealed that both grain size and porosity changed gradually from the catalytically active layer (near the electrodeelectrolyte interface) to the current collection layer (near the electrode-interconnect interface). Impedance analysis showed that a 3-layer LSCF cathode with graded microstructures exhibited much-improved performance compared to that of a single-layer LSCF cathode, corresponding to interfacial resistance of 0.053, 0.11, and 0.27 $\Omega{\cdot}cm^2$ at 800, 750, and $700^{\circ}C$ respectively.

• 한국세라믹학회지
• /
• 제50권6호
• /
• pp.423-428
• /
• 2013

Porous YSZ ceramics are fabricated using 3 mol% yittria-stabilized zirconia (3YSZ) and NiO with different particlesizes (0.6 and 7 ${\mu}m$). Nickel oxide (NiO) is added to the YSZ powder as a pore former with different amounts(40, 50, and 60 vol%) and at different sintering temperatures (1350 and $1400^{\circ}C$) are applied in order to evaluate the temperature effects on the pore and mechanical properties. Heat treatment is conducted after sintering at $700^{\circ}C$ in $H_2$ for the NiO reduction process; then, Ni is removed using a $HNO_3$ etchant solution. According to the NiO contentand sintering temperatures, 41-67% porous YSZ ceramic is obtained and the flexural strength increases, while the porosity decreases with an increasing sintering temperature. The optimum flexural strength ($136.5{\pm}13.4MPa$) and porosity (47%) for oxygen transport porous YSZ membrane can be obtained with 40 vol% of 7 ${\mu}m$ NiO particle at a sintering temperature of $1350^{\circ}C$.

• 한국지구과학회지
• /
• 제43권5호
• /
• pp.639-646
• /
• 2022

경상분지 신동층군의 백악기 진주층 일부 사암에서 산출되는 흑색의 불투명 탄화수소인 고열역청(pyrobitumen)의 산상을 처음으로 보고한다. 고열역청은 녹니석 공극벽 선충진(pore-lining) 교결물을 피복하거나 교결물 끝부분에 스며들어간 상태로 산출되므로, 녹니석 교결물 침전 이후에 생성된 것이며, 이는 과거 원유가 존재했음을 지시한다. 액상의 탄화수소는 진주층이 상당한 깊이로 매몰되는 동안 유입되었으며, 진주층 사암은 저류암의 역할을 했던 것으로 보인다. 진주층에 고열역청이 존재하는 것은 진주층이 액상 탄화수소의 이동 이후 심부 매몰과정을 겪었음을 지시한다. 그 후 매몰 온도가 더 증가하면서 탄화수소의 열분해가 일어나고 고열역청이 저류암에 잔류물로 남게 되었다.

• 공업화학
• /
• 제7권1호
• /
• pp.186-193
• /
• 1996

몇 가지 키토산 비드들을 W/O 에멀젼법과 capillary extrusion법에 의해 제조하여, SEM 사진을 통해 표면 구조와 표면적의 차이를 관찰하였고, BET법으로 표면적을 측정하였으며, 피크린산 적정에 의해 유효 아민함량을 측정하여 상기 결과들과의 상관관계를 알아 보았다. W/O 에멀젼법에 의해 제조한 비드의 경우 capillary extrusion법에 의해 제조된 비드들보다 입자의 크기가 작았으며, 반대로 표면적, 유효 아민함량은 높게 나타났다. 또한 비드의 표면적, 유효 아민함량, 겉보기 밀도(apparent density) 및 기계적 강도(hardness)는 제조시 건조방법에 따라 매우 큰 편차를 나타내었다. Hardness 측정결과 solvent dehydration법에 의해 건조된 비드들이 동결건조법에 의해 건조된 비드들에 비해 높은 강도를 나타내었다. 또한 겉보기 밀도에 있어서도 solvent dehydration한 비드들이 동결건조한 비드들에 비해 높은 겉보기 밀도를 보였다. SEM 사진 분석결과 solvent dehydration법에 의한 비드들은 매우 작은 pore들이 비드의 표면에 무수히 존재한 반면 동결건조한 비드에서는 벌집모양의 pore들이 존재하고 있음을 알 수 있었다. 피크린산 적정결과 solvent dehydration한 비드의 경우 동결건조한 비드보다 약 10배의 높은 유효 아민함량을 나타내었으며 비드의 표면적이 클수록 유효 아민함랑은 높게 나타났다. 또한 fluorescamine을 반응시킨 후 형광현미경으로 관찰하여 비드의 표면과 내부의 pore 주위에 노출된 1차 아민의 존재를 정성적으로 확인할 수 있었다.

• 대한화학회지
• /
• 제29권2호
• /
• pp.144-150
• /
• 1985

스티렌과 디비닐벤젠을 이용한 공중합체의 합성에 희석제로서 헵탄과 톨루엔을 사용하여 다공성 및 미세구조에 미치는 영향을 조사하였다. 스티렌디비닐벤젠 공중합체를 아미노화하여 음이온 교환수지를 합성하였으며 이 수지의 이온교환용량과 알코올 수용액에서 붕산에 대한 분포계수 값을 구하였고 이온교환 크로마토그래피와 질량분석기를 이용하여 붕소의 동위원소 분리효과를 연구하였다.

• Carbon letters
• /
• 제6권4호
• /
• pp.243-247
• /
• 2005

Plasma polymerization of allylamine subsequently after plasma pre-treatment was conducted on the activated carbon fibers (ACFs) for the immobilization of amine groups in the surface of ACFs. The change of structural properties of ACFs with respect to different polymerization conditions was investigated through BET method. The change of surface morphologies of ACFs with respect to different plasma polymerization power was also studied through AFM. It was found that the structural properties such as specific surface area and micropore volume could be optimized under certain plasma deposition conditions. It was reckoned that treatment and deposition showed adverse effect on plasma polymerization, in which the former developed the micro-structures of the ACFs and the latter tended to block the micro pores. The Fourier transform infrared spectroscopy (FTIR) revealed that the poly(allylamine) was successfully immobilized on the surface of ACFs and the amount of the deposited polymer layer was related to the plasma polymerization power. SEM results showed that the plasma deposited polymer layer were small and homogenously distributed. The size and the distribution of particles deposited were closely related to the plasma polymerization power, too.

• Carbon letters
• /
• 제12권1호
• /
• pp.1-7
• /
• 2011

In the present study, the removal of Pb (II) ions on oxidized activated carbons (ACs) was investigated. ACs were derived from activation of indigenous cotton stalks waste with potassium hydroxide (KOH) in two-stage process. The KOH-ACs were subjected to liquid-phase oxidation with hot $HNO_3$ and one untreated sample was included for comparison. The obtained carbons were characterized by Fourier transform infrared (FTIR), slurry pH and $N_2$-adsorption at 77 K, respectively. Adsorption capacity of Pb (II) ions on the resultant carbons was determined by batch equilibrium experiments. The experimental results indicated that the oxidation with nitric acid was associated with a significant increase in mass of yield as well as a remarkable reduction in internal porosity as compared to the untreated carbon. The AC-800N revealed higher adsorption capacity than that of AC-800, although the former sample exhibited low surface area and micropore volume. It was observed that the adsorption capacity enhancement attributed to pore widening, the generation of oxygen functional groups and potassium containing compounds leading to cation-exchange on the carbon surface. These results show that the oxidized carbons represented prospective adsorbents for enhancing the removal of heavy metals from wastewater.

• 한국환경보건학회:학술대회논문집
• /
• 한국환경보건학회 2005년도 국제학술대회
• /
• pp.365-370
• /
• 2005

The objective of this study is to develop the sorbent of oyster shell, which can remove gaseous acid pollutants emitted from the incinerator and power plants. The physicochemical properties of prepared absorbents have been measured using ICP and BET Also, this study is to investigate the Hydration/calcination reaction in the fixed bed reactor. Thus, the results could be summarized as follows. Oyster shell can be used in powder type without former processing. It should be also noted that sulfation reactivity of oyster sample increases to about 5 times by calcination/hydration reaction due to the increase of specific surface area and pore volume. From these experiments, we have found that both $SO_2$ and $NO_x$ in simulated flue gas can be effectively removed by use of oyster absorbent.

• Carbon letters
• /
• 제2권1호
• /
• pp.15-21
• /
• 2001

In this work, activated carbon fibers (ACFs) were plated with copper metal using electroless plating method and the effects of surface properties and pore structures on chromium adsorption properties were investigated. Surface properties of ACFs have been characterized using pH and acid/base values. BET data with $N_2$ adsorption were used to obtain the structural parameters of ACFs. The electroless copper plating did significantly lead to a decrease in the surface acidity or to an increase in the surface basicity of ACFs. However, all of the samples possessed a well-developed micropore. The adsorption capacity of Cr(III) for the electroless Cu-plated ACFs was higher than that of the as-received, whereas the adsorption capacity of Cr(VI) for the former was lower than that of the latter. The adsorption rate constants ($K_1$, $K_2$, and $K_3$) were also evaluated from chromium adsorption isotherms. It was found that $K_1$ constant for Cr(III) adsorption depended largely on surface basicity. The increase of Cr(III) adsorption and the decrease of Cr(VI) adsorption were attributed to the formation of metal oxides on ACFs, resulting in increasing the surface basicity.