• Membrane and Water Treatment
• /
• v.8 no.6
• /
• pp.563-574
• /
• 2017

Antibacterial effective, high performanced, novel ZnO embedded composite membranes were obtained by blendig ZnO nanoparticles with polysulfone. IR, TG/DTG, XRD and SEM analysis were performed to characterize structure and morphology of ZnO nanoparticles and composite membranes. Contact angle, EWC, porosity and pore structure properties of composite membranes were investigated. Cross-flow filtration studies were performed to investigation of performances of prepared membranes. It was found from the cross section SEM images that ZnO nanoparticles dispersed homogenously up to additive amount of 2% and the membrane skin layer thicknesses increased in the presence of ZnO. Contact angle of pure PSf membranes were reduced from $70^{\circ}$ to $55^{\circ}$ after addition of 4% ZnO. Porosity of composite membrane contains 1% ZnO was higher about 22% than pure PSf membrane. BSA rejection ratio and PWF of 0.5% ZnO embedded composite membrane became 2.2 and 2.3 times higher than pure PSf membrane. It was determined from flux recovery ratios that ZnO additive increased the fouling resistance of composite membranes. Also, the bacterial killing ability of ZnO is well known and there are many researches related to this in the literature. Therefore, it is expected that prepared composite membranes will show antibacterial effect.

• Membrane Journal
• /
• v.25 no.2
• /
• pp.99-106
• /
• 2015

Polysulfone (PSF) hollow fiber membrane was prepared to separate $CO_2$ from the flaring gas. Fabricated PSF membrane system was fulfilled under 1 stage, 2 stage membrane process and simulation in order to confirm the operating condition for 99% of $CH_4$ and 1% of $CO_2$ concentration. Also, $25Nm^3/h$ bench scale $CO_2$ separation membrane system was operated under 1% of $CO_2$ concentration during 100 hr, and $CH_4$ recovery ratio was 98%.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1993.04a
• /
• pp.31-32
• /
• 1993

본 연구는 내열성, 내약품성, 내유기용매성 등 물리, 화학적 성질이 우수한 PSF(Polysulfone)와 PI(Polyimide)계의 고분자를 화학적 개질을 통하여 친수성을 높히는 목적으로 술폰화 반응을 시켰다. 이러한 이온성이 부가된 PS와 PI막의 제조와 투과 특성을 측정 조사하였다.

• Macromolecular Research
• /
• v.9 no.5
• /
• pp.285-291
• /
• 2001

The polysulfone(PSf)/polyethersulfone(PES) blend membranes were prepared by an immersion precipitation method. N-methyl-2-pyrrolidone(NMP) was used as a solvent and water as a nonsolvent. The composition of the coagulation bath and the dope polymer concentration as well as the blend ratio of two polymers were varied. The membrane morphologies were interpreted on the basis of the phase diagram of the PSf/PES/NMP/water system. As the solvent content in the coagulation bath increased in the single polymer system, the number of macrovoids decreased and the morphology was changed from finger-like to cellular structure. In the given bath condition phase separation occurs earlier for the solutions of PSf/PES blend than for those of single polymer. A horizontally layered structure and horizontal protuberances inside the macrovoid were observed for the membranes formed from PSf/PES blend solutions. This peculiar structure formation can be interpreted by a PSf-rich/PES-rich phase separation followed by a polymer-rich/polymer-lean phase separation during the exchange of solvent and nonsolvent.

• Membrane and Water Treatment
• /
• v.7 no.1
• /
• pp.39-53
• /
• 2016

In this study, polysufone (PSf) was used as a base polymer to synthesize sulfonated polysulfone (SPSf) and aminated polysulfone (APSf) as cation and anion exchange polymers, respectively. Then the ion exchange polymers were coated onto the surface of commercial carbon electrodes. To compare the capacitive deionization (CDI) and membrane capacitive deionization (MCDI) processes, the pristine carbon electrodes and ionic polymer coated electrodes were tested under various operating conditions such as feed flow rate, adsorption time at fixed desorption time, and feed concentration, etc., in terms of effluent concentration and salt removal efficiency. The MCDI was confirmed to be superior to the CDI process. The performance of MCDI was 2-3 times higher than that of CDI. In particular, the reverse desorption potential was a lot better than zero potential. Typically, the salt removal efficiency 100% for 100 mg/L NaCl was obtained for MCDI at feed flow rate of 15 ml/min and adsorption/desorption time of 3 min/1 min and applied voltages 1.0 V for adsorption and -0.3 V for desorption process, and for 500 mg/L, the salt removal efficiency 91% was observed.

• Membrane Journal
• /
• v.26 no.4
• /
• pp.281-290
• /
• 2016

Thin film composite (TFC) polyamide membranes were prepared on polysulfone (PSF) supports for forward osmosis (FO) applications. To understand the influence of polarity and porosity of support layer on the formation of polyamide structure and the final FO performance, clathochelate metal complex (MC) contained PSF supports were prepared via the phase inversion process from various PSF casting solutions containing 0.1-0.5 wt% of MC in dimethyl formamide (DMF) solvent (18 wt%). A crosslinked aromatic polyamide layer was then fabricated on top of each support to form a TFC membrane. For the porous PSF supports prepared with relatively low concentration casting solutions (12 wt%), the PET film was removed after phase inversion and crosslinked aromatic polyamide layer was then fabricated. The tested sample from PSF (18 wt%)/MC (0.5 wt%) casting solution presented outstanding FO performance, almost similar water flux (9.99 LMH) with lower reverse salt flux (RSF, 0.77 GMH) compared to commercial HTI FO membrane(10.97 LMH of flux and 2.2 GMH of RSF). By addition of MC in casting solution, the thickness of the active layer in FO membranes was reduced, however, the increased RSF value was obtained.

• Membrane Journal
• /
• v.33 no.6
• /
• pp.439-446
• /
• 2023

Ceramic membranes are generally used for various industrial processes operating under extreme conditions because of its high thermal and chemical stability. However, due to the trade-off phenomenon of permeability and mechanical strength, preparation of high permeability-high strength membrane is necessary. In this study, the change in characteristics and performances of ceramic membranes was analyzed depending on the type of polymer binder and its mixing ratio. Because the solubility between solvent and polymer binder was higher in PSf (polysulfone) than in PES (polyethersulfone), the viscosity and discharge pressure of the PSf-based dope solution were higher than those of PES-based dope solution. When PSf was used as a polymer binder, ceramic membrane showed high mechanical strength and low water permeability due to the dense structure. On the other hand, in case of PES, the mechanical strength was slightly reduced and the water permeability was increased. It was confirmed that the optimum mixing ratio of the PSf and PES with high water permeability and mechanical strength was 9:1.

• Applied Chemistry for Engineering
• /
• v.22 no.3
• /
• pp.277-285
• /
• 2011

Polysulfone (PSf) membranes were prepared via the phase inversion process. Polyvinylpyrrolidone (PVP) was added as a nonsolvent additive in the casting solution containing a mixture of PSf and n-methylpyrrolidone. The added PVP played a role of enhancing liquid-liquid phase separation of the casting solution, and significantly reduced the solution fluidity. When prepared via the diffusion-induced process using water as a precipitation nonsolvent, the solidified membranes revealed a typical asymmetric structure irrespective of the addition of PVP. With 5 wt% PVP content, the finger-like cavities were more developed in the membrane sublayer compared to that of the membranes prepared without PVP. In contrast, with more than 10 wt% of PVP, the formation of finger-like cavities was suppressed, and the thickness of polymer nodule layer was increased. The surface porosity was also increased with the PSf content in the casting solution. The water permeability curve as a function of PVP addition revealed the inflection point. The maximum water permeability for 12 wt% PSf membrane was obtained with 5 wt% PVP content, and that for 18 wt% PSf membrane with 15 wt% PVP.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.1
• /
• pp.57-62
• /
• 2000

Sulfonated Polysulfone (SPSF) cation-exchange membranes were synthesized by introducing various ratio of chlorosulfuric acid (CSA) onto the main chain of polysulfone (PSF). Properties such as ion exchange capacity, water content, liked ion concentration, and partition coefficient were measured, respectively. Through the analysis of DSC and TGA, it has been shown that glass transition temperature increased and weight loss decreased as sulfuric acid group concentration increased. Structure of membrane measured by AFM and SEM was seen to be asymmetric. Apparent diffusion coefficient of sodium ions through SPSF membrane by AC impedance was increased as sulfuric acid group concentration increased.

• Membrane Journal
• /
• v.20 no.3
• /
• pp.235-240
• /
• 2010

The aim of this paper is to evaluate and compare the performances of forward osmosis (FO) membranes using different materials. The FO membranes were synthesized using interfacial polymerization method on hydrophobic polysulfone (PSf) and relatively hydrophilic polyethersulfone (PES) supports. The FO performance such as flux and back diffusion was measured. The resulting fluxes of PSf and PES FO membranes were $4.3\;L/m^2hr$ and $17.8\;L/m^2hr$, respectively. The flux of the PES FO membrane was higher than that of the PSf FO membrane. The results indicated that hydrophillictity of the support membrane is important for increasing flux in FO process. Moreover, with decreasing the support layer thickness, flux increased considerably.