• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.40 no.2
• /
• pp.161-165
• /
• 2004

The main goal of this work is to study the effect of glass fiber volume fraction on the result of tensile test with respect to glass fiber/polypropylene(GF/PP) composites. The tensile test and failure mechanisms of GF/PP composites were investigated in the fiber volume fraction range from 10% to 30%. The tensile strength and the fracture strength increased with the increasing of the fiber volume fraction in the tested range. Fiber pull-out and debonding of this composites increased with the fiber volume fraction in thc tested range. The major failure mechanisms were classified into the debonding, the fiber pull out, the delamination and the matrix deformation.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.108-111
• /
• 2004

The polypropylene(PP) fiber is poised as a low cost alternative for reinforcement in structural applications in comparison with other high performance fibers, such as the polyvinyl-alcohol(PVA), polyethylene, carbon and aramid fiber. The mechanical properties of the composite are strongly determined by the interfacial behavior of fiber and cementitious matrix. The crack bridging mechanism contribute to composite toughness from activation of the fiber-matrix interface where energy is dissipated through debonding of the interface and fiber pullout. In this study, therefore, the pullout behavior of PP fibers is investigated. Experimental work includes the investigation of the interfacial properties, and the composite property. The quantification of interfacial properties, the frictional bond is achieved through single fiber pullout test. A study on the effect of inclination angle on fiber pullout behavior is also conducted.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.41 no.1
• /
• pp.72-78
• /
• 1999

The purpose of this study was to evaluate the properties of unconfined strength of dry soil which was reinforced with polypropylene fiber. It is found that unconfined compressive strength and strain of dry soil without fiber were decreased as water content was increased. As mixing ration of fiber was increased , unconfined compressive strength and failure strain of dry soil reinforced with polypropylene fiber were increased. When mixing ration was larger than 0.5 % , unconfined compressive strength was gradually increased. The longer fiber was, the largest post peak strength was obtained and the larger strain was reached. Tensile strength of dried fiber reinforced soil was larger than that of dry soil without fiber.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.575-578
• /
• 2005

Recently, various concrete reinforcing fibers have been used to reduce the plastic shrinkage cracking which occurs before the concrete hardens. In this study, the physical properties of nylon fiber reinforced concrete such as slump, air content, compressive strength and tensile strength were investigated. In addition, the performance of nylon fiber in the plastic shrinkage cracking reduction of mortar has been estimated in comparison with polypropylene fiber and cellulose fiber. Nylon fiber showed considerable advantages in terms of the workability of concrete and the plastic shrinkage cracking reduction of mortar compared with polypropylene fiber and cellulose fiber.

• Journal of the Korea Institute of Building Construction
• /
• v.12 no.2
• /
• pp.183-193
• /
• 2012

Compressive property of high strength concrete with amorphous metal fibers subject to high temperature has been investigated. The measure of this investigation includes explosive spalling, weight loss, residual compressive strength, strain at peak stress, elastic modulus, and residual energy absorption capacity after exposure to $400^{\circ}C$, $600^{\circ}C$and $800^{\circ}C$. In addition to the amorphous metal fiber, two other types of fibers (polypropylene fiber and hooked-end steel fiber) were also included in this investigation for comparison. The experimental program was conducted with high strength concrete using several combinations of the fiber types. The testing result shows that the concrete with amorphous metal fibers plus polypropylene fibers shows a superior behavior than those using other combination or single fiber type ingredient.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.47 no.6
• /
• pp.59-70
• /
• 2005

A series of resonant column test was performed to investigate the dynamic deformation characteristics of silty sand soils mixed with polypropylene fibrillated type fiber. Results show that optimum mixing ratios were $0.2\%$ for 19mm of cut fiber for shear modulus and $0.1\%$ for 60mm cut fiber fur damping ratio. As shear strain was increased, normalized values of shear modulus (G(Reinforced)/ G(Unreinforced)) of fiber reinforced soil were increased up to $10^{-3}\%\~10^{-1}\%$ ranges. However, normalized damping ratio (D(Reinforced/D(Unreinforced)) was diminished with an increase in strain beyond $10^{-3}\%\~10^{-1}\%$ for the damping capacity of soils mixed with fiber. Normalized shear modulus $(G/G_{max})$ obtained from the test was plotted in the chart suggested by Seed and Idriss. The shear modulus of silty sand was located between sand and gravel curves.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.661-664
• /
• 2006

Recently, various concrete reinforcing fibers have been used to reduce the plastic shrinkage cracking which occurs before the concrete hardens. In this study, the physical properties of nylon fiber reinforced concrete such as slump, air content, compressive strength and tensile strength were investigated. In addition, the performance of nylon fiber in the plastic shrinkage cracking reduction of concrete has been estimated in comparison with polypropylene, poly vinyl alcohol fiber and cellulose fiber. Nylon fiber showed considerable advantages in terms of the workability of concrete and the plastic shrinkage cracking reduction of concrete compared with polypropylene fiber and cellulose fiber.

• Composites Research
• /
• v.33 no.3
• /
• pp.161-168
• /
• 2020

In this paper, we have studied the mechanical properties of thermoplastic carbon fiber fabric composites with spread technology and compression molding temperature were investigated. Carbon fiber reinforcement composites were fabricated using commercial carbon fiber fabrics and spread carbon fiber fabrics. Mechanical properties of the commercial carbon fiber composites (CCFC) and spread carbon fiber composites (SCFC) according to compression molding temperatures were investigated. Thermal properties of the polypropylene film were examined by rheometer, differential scanning calorimetry, thermal gravimetric analysis. Tensile, flexural and Inter-laminar shear test. Commercial carbon fiber reinforcement composites and spread carbon fiber composites were fabricated at 200~240℃ above the melting temperature of the polypropylene film. Impregnation properties according to compression molding temperature of the polypropylene film were investigated by scanning electron microscopy. As a result, as the compression molding temperature was increased, the viscosity of the polypropylene film was decreased. The mechanical properties of the compression molding temperature of 230℃ spread carbon fiber composite was superior.

• Fibers and Polymers
• /
• v.7 no.4
• /
• pp.432-435
• /
• 2006

High Modulus and high tenacity polypropylene fibers have been prepared by drawing on a gradient heater. Results show that fiber properties are significantly affected by temperature profiles of final stage drawing on a gradient heater. The gradient drawn filaments showed superior mechanical properties when compared to filaments drawn over a constant temperature heater. Fibers with initial modulus of 16.4 GPa and tenacity of 670 MPa have been manufactured in the process. The nature of the gradient drawing had a significant effect on end properties. The superior mechanical properties are attributed to the high crystal perfection and crystallinity and low void fractions obtained at high draw ratios when drawn over a gradient heater.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2008.10a
• /
• pp.73-74
• /
• 2008

Three primary color super hydrophobic dyes were used to dye unmodified polypropylene fiber for various practical color. The color values of the dyed fibers were displayed on CIE 1931 Yxy chromaticity diagram. It was found that they showed various colors between three primary colors on the unmodified polypropylene fiber.