• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.129.2-129.2
• /
• 2010

AEM which were used for solid alkaline fuel cell(SAFC) were prepared by photo polymerization in method pore-filling with various quaternary ammonium cationic monomers and crosslinkers without an amination process. Their specific thermal and chemical properties were characterized through various analyses and the physico-chemical properties of the prepared electrolyte membranes such as swelling behavior, ion exchange capacity and ionic conductivity were also investigated in correlation with the electrolyte composition. The polymer electrolyte membranes prepared in this study have a very wide hydroxyl ion conductivity range of 0.01 - 0.45S/cm depending on the composition ratio of the electrolyte monomer and crosslinking agent used for polymerization. However, the hydroxyl ion conductivity of the membranes was relatively higher at the whole cases than those of commercial products such as A201 membrane of Tokuyama. These pore-filling membranes have also excellent properties such as smaller dimensional affects when swollen in solvents, higher mechanical strength, lowest electrolyte crossover through the membranes, and easier preparation process compared of traditional cast membranes. The prepared membranes were then applied to solid alkaline fuel cell and it was found comparable fuel cell performance to A201 membrane of Tokuyama.

• 한국군사과학기술학회지
• /
• 제20권4호
• /
• pp.528-535
• /
• 2017

Fuel cells have been spotlighted in the world for being highly efficient and environmentally friendly. A hydrogen which is the fuel of fuel cell can be obtained from a number of sources. Hydrogen source for operating the polymer electrolyte membrane fuel cell(PEMFC) in the current underwater environment, such as a submarine and unmanned underwater vehicles are currently from the metal hydride cylinder. However, metal hydride has many limitations for using hydrogen carrier, such as large volume, long charging time, limited storage capacity. To solve these problems, we suggest diesel reformer for hydrogen supply source. Diesel fuel has many advantages, such as high hydrogen storage density, easy to transport and also well-infra structure. However, conventional diesel reforming system for PEMFC requires a large volume and complex CO removal system for lowering the CO level to less than 10 ppm. In addition, because the preferential oxidation(PROX) reaction is the strong exothermic reaction, cooling load is required. By changing this PROX reactor to hydrogen separation membrane, the problem from PROX reactor can be solved. This is because hydrogen separation membranes are small and permeable to pure hydrogen. In this study, we conducted the pressurized diesel reforming and water-gas shift reaction experiment for the hydrogen separation membrane application. Then, the hydrogen permeation experiments were performed using a Pd alloy membrane for the reformate gas.

• Bulletin of the Korean Chemical Society
• /
• 제31권8호
• /
• pp.2141-2142
• /
• 2010

• 에너지공학
• /
• 제11권3호
• /
• pp.254-261
• /
• 2002

The fabrication method for the main components of the polymer electrolyte membrane fuel cell stack such as electrodes, membrane-electrode assemblies, and bipolar plates was established for the effective electrode area of 240 ㎠. A counter-flow type 100-cell stack was fabricated by using the above components and then a maximum power of 7.44 kW for H$_2$/O$_2$ and 5.56 kW for H$_2$/air could be obtained at 70$\^{C}$ and 1 atm. It was seen that the distribution of the OCV for unit cells in the stack was uniform but the voltage deviation increased as the load increased due to the IR drop and the electrode polarization. The stack was applied to the power source of the fuel cell/battery hybrid electric golf car. It produced about 1 kW at a room temperature operation during the test run, which occupied about 43% of the total power required by the 2.3 kW motor.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.90.1-90.1
• /
• 2010

The design and fabrication of a metallic bipolar plate-gasket assembly for polymer electrolyte fuel cells (PEMFCs) is defined. This bipolar plate-gasket assembly was prepared by inserting a previously prepared bipolar plate in the specially designed gasket mold. For this aim, a proprietary fluoro-silicone based rubber was injected directly into the bipolar plate borders. Gaskets obtained like this showed the chemically / physically stable and the good sealibilty in typically operating PEM fuel cell conditions. And also, this bipolar plate-gasket assembly shows lots of advantages with respect to traditional PEMFCs stack assembling systems: useful application to automative stacking due to easy handling, reduced fabrication time, possibility of quality control and failed elements substitution. This bipolar plate-gasket assembly was evaluated in the short fuel cell stack and met the leakage requirement for normal operation both in short-term and in long-term operation. Especially, it was confirmed that this gasket could be applied successfully even in the high pressure FEM fuel cell systems(over 2.0 bar in absolute pressure).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1722-1724
• /
• 2005

The focus of this paper is to develop a mathematical model for investigating the dynamic performance of a polymer electrolyte membrane fuel cell. The model in this work is based on physical laws having clear significance in replicating the fuel cell system and can easily be used to set up different operational strategies. Simulation results display the transient behavior of the voltage within each single cell, and also within a number of such single cells combined into a fuel cell stack system. A linear as well as a nonlinear analysis of the polymer electrolyte membrane fuel cell system(PEMFC) has been discussed in order to present a complete and comprehensive view of this kind of modeling. Also, a comparison of the two kinds of analysis has been performed. Finally, the various characteristics of the fuel cell system are plotted in order to help us understand its dynamic behavior. Results indicate that there is a considerable amount of error in the modeling process if we use a linear model of the fuel cell. Thus, the nonlinearities present in the fuel cell system should be taken into account in order to obtain a better understanding of the dynamic behavior of the fuel cell system.

• 조명전기설비학회논문지
• /
• 제23권1호
• /
• pp.59-68
• /
• 2009

분산진원으로서 연료전지 발전장치는 100w부터 수백[kw]의 용량을 가지며 종전의 대규모 전력설비와 비교하여 높은 신뢰도를 갖는 고품질의 전력을 공급할 수 있다. 본 연구에서는 소형 분산전원으로서 PEMFC(polymer electrolyte membrane fuel cell)연료전지 발전장치에 대한 PSIM(power electronics simulation tool) 모델을 설정하고 이를 바탕으로 DSP(digital signal processor)기반의 연료전지 하드웨어 시뮬레이터를 구현하였다. 연료전지 전류와 출력전압과의 관계는 연료전지의 전압-전류(V-I) 곡선 중 ohmic영역에서 1차 함수로 간략화 하였다. 구현된 시스템은 PEMFC 하드웨어 시뮬레이터, 절연형 풀 브리지 직류 부스트 컨버터 그리고 60[Hz] PWM인버터로 구성되어있다. 부하변동 및 과도상태에 대한 연료전지 하드웨어 시뮬레이터의 전압-전류-전력(V-I-P) 특성을 파악하였으며, 저항 부하 및 비선형 부하에 대한 전력변환기의 60[Hz] 정현파 교류출력 전압파형을 고찰하였다.

• 전기화학회지
• /
• 제6권1호
• /
• pp.36-40
• /
• 2003

고분자 전해질 연료전지를 자동차용 동력원으로 사용하는 경우 겨울철 운전 시 연료전지 내에 존재하는 물이 결빙하여 연료전지의 성능을 저하시킬 수 있다. 물의 결빙이 연료전지의 성능에 미치는 영향을 조사하기 위해 연료전지의 온도를 운전온도인 $80^{\circ}C$에서 물이 결빙하기에 충분한 온도인 $-10^{\circ}C$까지 열순환하면서 전류전압 곡선을 측정했다. 열순환이 반복됨에 따라 물의 상변화와 이에 따른 부피변화로 인해 연료전지의 성능이 감소했다. 물의 결빙이 연료전지의 성능을 저하시키는 원인을 규명하기 위해 BET분석과 순환전류전압법, 임피더스 분석을 이용해 열순환이 전극의 구조와 분극 저항에 미치는 영향을 조사했다.

• 멤브레인
• /
• 제32권6호
• /
• pp.442-455
• /
• 2022

고온 구동형 고분자 전해질 막 연료전지(high temperature polymer electrolyte membrane fuel cell, HT-PEMFC)는 전극의 빠른 활성과 피독 현상에 대한 높은 저항성으로 인해 저온 구동형 PEMFC의 대안으로 많은 연구가 진행되고 있다. 폴리벤즈이미다졸(polybenzimidazole, PBI)을 기반으로 한 PEM의 경우 고온 구동 조건에서 이온 전도성 물질과의 높은 상호 작용과 우수한 열적ㆍ기계적 안정성 특징으로 인해 HT-PEMFC용 PBI 기반 전해질 막 개발과 관련된 다양한 연구들이 진행되고 있다. 본 총설에서는 고성능/고내구성의 PBI 기반 PEM을 개발하기 위해 1) 인산 및 다양한 이온전도성 물질이 도핑된 PBI 막의 특성 분석과 막 제조법에 따른 PBI 막의 물성 비교에 관한 연구를 우선적으로 살펴본 후 2) 다공성 폴리테트라플루 오르에틸렌 지지체 및 무기 입자 혼입을 통한 PBI 복합 막의 성능 개선 연구 및 3) 고분자 블렌딩을 통해 가교 구조가 도입된 PBI 기반 가교 막의 내구성 향상에 관한 연구 동향에 대하여 소개하고자 한다.

• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 2003년도 연료전지심포지움 2003논문집
• /
• pp.169-171
• /
• 2003

Organic/inorganic hybrid membranes have been prepared and evaluated as polymer electrolytes in a polymer electrolyte membrane fuel cell (PEMFC). Previously, partially fluorinated poly (arylenether) was synthesized and the polymer was sulfonated by fuming sulfuric acid$(30\%\;SO_3)$. Modification of these polymers with coupling agent and inorganic materials was carried out to prepare membranes. Membranes cast from these materials were investigated in relation to the proton conductivity and weight loss at the room temperature. It was found that these membranes had a higher conductivity of $10^{-2}\;Scm^{-1}$ at the room temperature. But inorganic materials have leaked out from the hybrid membrane. If this problem is resolved, organic/inorganic hybrid membranes will become satisfactory Polymer electrolytes for the PEMFC.