• 한국전기전자재료학회논문지
• /
• 제17권8호
• /
• pp.893-897
• /
• 2004

In this paper, we studied the mechanical and thermal properties on slice XLPE sheet from 22 kV and 154 kV power cables. Interface structures are XLPE/semiconductor and XLPE/water/semiconductor. We evaluated mechanical property, thermal analysis, moisture analysis. Based on mechanical and thermal properties of the 22 kV XLPE sheet, elongation, mechanical strength, and melting point were evaluated to be 485.48 %, 1.74 kgf/$\textrm{mm}^2$ and $102.48^{\circ}C$, respectively. It was also evaluated from the mechanical and thermal properties of 154 kV XLPE sheet that elongation, mechanical strength, and melting point are 507.81 %, 1.8 kgf/$\textrm{mm}^2$, $106.9^{\circ}C$, respectively. A region shows a rapid increase in tension strength, and B region only shows increase in elongation under 1.0 kgf/$\textrm{mm}^2$, C region shows increase in both elongation and tension strength. Difference of melting point came from the chain of XLPE polymer and the difference of crystallization. Moisture density of semiconductor showed 800 ∼ 1200 ppm before extrude, 14000 ∼24000 ppm after extrude. These values were higher than the moisture density of XLPE (300∼560) ppm.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.976-981
• /
• 2006

In case of attaching thermoelectric module and heat source, the polymer pad is attached on the $Al_2O_3$ plate, which is cooling side of thermoelectric module, in order to enhance mechanical safety of the system. It is impossible to calculate the exact distribution of temperature and flow pattern of inner gap of thermoelectric module. Therefore CFD(Computational Fluid Dynamics) analysis was executed to determine the thermo-fluid phenomena and distribution by Fluent. As the result of these analysis, heat transfer was dominated by conduction and the difference of temperature was linear distribution according to the thickness of polymer sheet.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2528-2533
• /
• 2007

Thermoforming is one of the most versatile and economical processes available for the manufacturing polymer products. The drawback of thermoforming is difficult to get uniform thickness of final products. For the distribution of thickness strongly depends on the temperature distribution of sheet, the adjustment of heater power is very important In this paper, an optimization study for getting uniform temperature distribution was carried out using dual optimization steps. At first, the steady state optimal distribution of heater power is searched by numerical optimization to get uniform temperature of sheet surface. In the second step, time-dependent optimal heater inputs have been found out to decrease the temperature difference through the direction of thickness using Rseponse Surface Method and D-optimal method. The optimization results show that the time-dependent optimal heater power distribution gives acceptable uniform sheet temperature in the field of forming temperature..

• 콘크리트학회논문집
• /
• 제24권4호
• /
• pp.473-480
• /
• 2012

아라미드 FRP로 보강된 RC 기둥의 전단보강효과를 평가하고자, 구조성능 실험을 수행하였다. 실험변수는 아라미드 시트 및 스트립 보강이며, 총 4개의 실험체를 대상으로 하였다. 실험 결과는 비보강 실험체를 기준으로 보강효과를 강도 및 에너지 능력 등을 평가하였다. 평가 결과 아라미드 시트보강이 강도증진과 아울러, 에너지 소산능력의 증진이라는 측면에서 매우 유효한 것으로 평가되었다.

• Korea-Australia Rheology Journal
• /
• 제11권3호
• /
• pp.225-232
• /
• 1999

This study presents 1-dimensional simple model for sheet casting or rectangular fiber spinning process. In order to achieve this goal, we introduce the concept of force flux balance at the die exit, which assigns for the extensional flow outside the die the initial condition containing the information of shear flow history inside the die. With the Leonov constitutive equation that predicts non-vanishing second normal stress difference in shear flow, we are able to describe the anisotropic swelling behavior of the extrudate at least qualitatively. In other words, the negative value of the second normal stress difference causes thickness swelling much higher than width of extrudate. This result implies the importance of choosing the rheological model in the analysis of polymer processing operations, since the constitutive equation with the vanishing second normal stress difference is shown to exhibit the characteristic of isotropic swelling, that is, the thickness swell ratio always equal to the ratio in width direction.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.840-845
• /
• 1999

In this study, it was experimentally investigated the effectiveness of repair and strengthening methods for RC beams deteriorated under severs enviromental conditions. Polymer cement were employed to restore the sectional loss and aramid fiber-reinforced sheet was used to reinforce the surface subject to tension. Repaired and strengthened reinforced-concrete samples were subjected to loading tests. The tests revealed that the sectional restoration enhanced the loading capability of the sample structures. Additional strengthening with one aramid fiber-reinforced sheet improved 18% of yielding load and 30% of ultimate load of the structure. Reinforcing with two aramid fiber-reinforced sheets brought about an enhancement of 22% of yielding loading and 49% of ultimate load.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2006년도 춘계학술논문 발표대회 제6권1호
• /
• pp.43-46
• /
• 2006

In this study on the appliable Asphalt sheet of monolithic and inorganic matter waterproofing material using of field because of problem of complex waterproofing sheet. Before this cement polymer modified waterproof coating and appliable asphalt sheet of monolithic whether have stability by method of construction about all style waterproofing that evaluate to new method of construction development naturally big emphasis put and try to approach. Did performance test item first at, as a result, drew by suitable thing in all KS items. This is considered to have more effective spot construction work because if means that have stability by material as well as method of construction.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 춘계 학술논문 발표대회
• /
• pp.103-104
• /
• 2018

Recently, in addition to greening of roof and artificial soil, Rootproofing to prevent damage to the waterproof layer and structures by roots is recognized as an important task. Therefore, various related products and construction methods have been developed and applied in the field. However, in the case of synthetic polymer-based sheets most commonly used in domestic construction sites, Most are produced using 100% new materials that are not suitable for green trends such as resource conservation and environmental protection. Therefore, in this study, we developed TPO sheet using recycled material, which is a technology that can secure eco-friendliness by utilizing recycled resources. As a result of the evaluation of tensile performance of the TPO sheet according to the recycled material content, The tensile strength of the specimens with the recycled content of 50 ~ 70% was the highest, The elongation rate of the specimen with the recycled content of 30 ~ 40% was the best.

• International Journal of Precision Engineering and Manufacturing
• /
• 제9권4호
• /
• pp.51-56
• /
• 2008

Thermoforming is one of the most versatile and economical processes available for shaping polymer products, but obtaining a uniform thickness of the final product using this method is difficult. Heater power adjustment is very important because the thickness distribution depends strongly on the distribution of the sheet temperature. In this paper, the steady-state optimum distribution of heater power is first ascertained by a numerical optimization to obtain a uniform sheet temperature. The time-dependent optimal heater input is then determined to decrease the temperature difference through the direction of the thickness using the response surface method and the D-optimal method. The optimal results show that the time-dependent optimum heater power distribution gives an acceptable uniform sheet temperature in the forming temperature range by the end of the heating process.

• 대한기계학회논문집A
• /
• 제41권2호
• /
• pp.137-142
• /
• 2017

최근 자동차 산업에서 경량화이면서 외부 충격에 민감한 시트 프레임은 안전성을 고려하여 꾸준히 연구개발되고 있다. 특히 본 연구에서는 고장력 강판과 폴리머의 이종 소재를 이용한 시트 프레임의 충격 특성에 대해 살펴보았다. 또한, 충격시 변위는 소재에 대해 굽힘 현상을 고려한 등가 굽힘강성식을 도입하여 살펴보았다. 층간 wire-web 구조물의 다양한 형상의 공학 디자인을 통해 충격시 변화가 적은 디자인을 설계하였으며, 육각형의 층간 wire-web 구조물이 외부 충격대비 안전계수가 높음으로 인해 흡수능력이 향상될 것으로 기대하고 있다. 이러한 연구 결과를 토대로 층간 wire-web 구조물의 설계를 통해 레진과의 함침을 높이고 이종 소재로써의 충격민감도에 유리한 제품을 개발할 수 있을 것으로 사료된다.