• 한국재료학회지
• /
• 제19권3호
• /
• pp.119-124
• /
• 2009

In the microelectronics packaging industry, the adhesion strength between Cu and polyimide and the thermal stability are very important factors, as they influence the performance and reliability of the device. The three different buffer layers of Cr, 50%Cr-50%Ni, and Ni were adopted in a Cu/buffer layer/polyimide system and compared in terms of their adhesion strength and thermal stability at a temperature of $300^{\circ}C$ for 24hrs. A 90-degree peel test and XPS analysis revealed that both the peel strength and thermal stability decreased in the order of the Cr, 50%Cr-50%Ni and Ni buffer layer. The XPS analysis revealed that Cu can diffuse through the thin Ni buffer layer ($200{\AA}$), resulting in a decrease in the adhesion strength when the Cu/buffer layer/polyimide multilayer is heat-treated at a temperature of $300^{\circ}C$ for 24hrs. In contrast, Cu did not diffuse through the Cr buffer layer under the same heat-treatment conditions.

• 한국전기전자재료학회논문지
• /
• 제17권2호
• /
• pp.196-200
• /
• 2004

Using polyimide Langmuir-Blodgett(LB) films as a tunneling harrier, we fabricated Au/Polyimide/1-layer arachidic acid/Pb structure in order to investigate electron transport properties through a junction. It was found that 9-layer polyimide LB films function as a good tunneling harrier in a study of current-voltage(I-V) chararteristics. And several peaks originating in the vibrational modes of the constituent molecules of 1-layer arachidic acid LB films were clearly observed in d$^2$V/dI$^2$- V corves.

• 한국재료학회지
• /
• 제17권12호
• /
• pp.664-668
• /
• 2007

The magnetron sputtering was used to deposit Ni buffer layers on the polyimide surfaces to increase the adhesion strength between Cu thin films and polyimide as well as to prevent Cu diffusion into the polyimide. The Ni layer thickness was varied from 100 to $400{\AA}$. The adhesion strength increased rather significantly up to $200{\AA}$ of Ni thickness, however, there was no significant increase in strength over $200{\AA}$. The XPS analysis revealed that Ni thin films could increase the adhesion strength by reacting with the polar C=O bonds on the polyimide surface and also it could prevent Cu diffusion into the polyimide. The Cu/Ni/ polyimide multilayer thin films showed a high stability even at the high heating temperature of $200^{\circ}C$, however, at the temperature of $300^{\circ}C$, Cu diffused through the Ni buffer layer into polyimide, resulting in the drastic decrease in adhesion strength.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.672-676
• /
• 2009

Polymide is widely used alignment material of recent commercial LCD panel structure. Generally, polyimide alignment material is classified soluble polyimide type and polyamic acid type with their main bond structure of solution state. specially, compared to polyamic acid alignment layer, soluble polyimide type alignment layer have excellent reliability during long term LCD driving cause of their high imidazation ratio(%), high voltage holding ratio(%) and low ion density. The other side, this type alignment materials has significant DC image stickicng side effect for using in-plane switching mode lcd structure cause of their slow DC discharging property. we applied inorganic salt to usual soluble polyimide type alignment layer and found out this technique had good DC image sticking property without any loss of reliability property in inplane switching LCD cell structure. This approach leads excellent DC image sticking property with maintaining high reliability property this approach confirmed improves an image sticking and a reliability simultaneously from the horizontality aligned LCD mode whose relatively bad image sticking property.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 춘계학술대회 논문집
• /
• pp.230-233
• /
• 1995

Using Polyimide Langmuir-Blodgett(LB) films as a tunneling barrier, Current -Voltage(I-V) characteristics and inelastic electron tunneling spectroscoupy(IETS) of the junctions incorporating 1-layer orgainc monolayer were invesgated. Several peaks originating in vibrational modes of constituted molecules of 1-layer monolayers were clearly observed in the IET spectra.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.506-508
• /
• 2007

We studied the nematic liquid crystal (NLC) alignment capability with a new alignment method utilizing an inkjet printed polyimide (PI) layer. A good, uniform LC alignment was achieved by the good PI printing using a new alignment method. The pretilt angle generated on the printed PI layer using the alignment method was almost the same as that on printed PI layer using rubbing alignment method. In addition, the good electro-optical performances of the new aligned twisted nematic (TN) cell with printed PI surface was obtained

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.261-264
• /
• 2007

We developed a non self-aligned poly-silicon TFTs fabrication process at two different temperatures on spin-coated polyimide layer above Si-wafer. After TFTs fabrication, the polyimide layer was mechanically released from the Si-wafer and the devices characteristics were compared. In addition self-heating and hot-carrier induced instabilities were analysed.

• 반도체디스플레이기술학회지
• /
• 제19권1호
• /
• pp.93-96
• /
• 2020

Polyimide thin film was prepared by annealing the polyamic acid that was synthesized through co-deposition of diamine and dianhydride. The polyamic acid and polyimide thin film were characterized with FT-IR and HR FE-SEM. The average roughness of the film surface, evaluated with AFM, were 0.385 nm and 0.299 nm after co-deposition, and annealing at 120 ℃ respectively. OLED was passivated with the polyimide layer of 200 nm thickness. While the inorganic passivation layer enhances the WVTR of OLED, the organic passivation layer gives flexibility to the OLED. The in-situ passivation of OLED with organic thin film layer provides the leading technique to develop flexible OLED Display.

• 한국재료학회지
• /
• 제17권2호
• /
• pp.61-67
• /
• 2007

The magnetron reactive sputtering was adopted to deposit CuO buffer layers on the polyimide surfaces for increasing the adhesion strength between Cu thin films and polyimide, varying $O_2$ gas flow rate from 1 to 5 sccm. The CuO oxide was formed through all the $O_2$ gas flow rates of 1 to 5 sccm, showing the highest value at the 3 sccm $O_2$ gas flow rate. The XPS analysis revealed that the $Cu_2O$ oxide was also formed with a significant ratio during the reactive sputtering. The adhesion strength is mainly dependent on the amount of CuO in the buffer layers, which can react with C-O-C or C-N bonds on the polyimide surfaces. The adhesion strength of the multi-layered Cu/buffer layer/polyimide specimen decreased linearly as the heating temperature increased to $300^{\circ}C$, even though there showd no significant change in the chemical state at the polyimide interface. This result is attributed to the decrease in surface roughness of deposited copper oxide on the polyimide, when it is heated.

• 한국전기전자재료학회논문지
• /
• 제35권1호
• /
• pp.58-65
• /
• 2022

The field of liquid crystal display (LCD) is constantly in the spotlight and the process of depositing an alignment layer in the LCD manufacturing process is very important to obtain excellent performance such as low-power driving and high-speed response to improve LCD performance. Therefore, research on liquid crystal (LC) alignment is being actively conducted. When manufacturing LCD, it is necessary to consider the effect of the alignment layer thickness as one of the factors affecting various LCD performances. In addition, previous studies confirmed the LC alignment characteristics correlate with the rotation speed in the spin coating process. Therefore, the electro-optical properties of the LCD were investigated by manufacturing a polyimide alignment layer by varying the rotation speed in the spin coating process in this study. It was confirmed that the thickness of the polyimide alignment layer was controlled according to the spin coating conditions. The average transmittances of anti-parallel LC cells at the spin coating speed of 2,500 rpm and 3,000 rpm are about 60%, which indicates that the LC cell has relatively higher performance. At the spin coating speed of 3,000 rpm, the voltage-transmittance curve of twisted nematic (TN) LC cell was below 1.5 V, which means that the TN LC cell operated at a low power. In addition, high-speed operating characteristics were confirmed with a response time of less than 30 ms. From these derived data, we confirmed that the ideal spin coating speed is 3,000 rpm. And these results provide an optimized polyimide alignment layer process when considering enhanced future LCD manufacturing.