• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.5
• /
• pp.851-856
• /
• 2017

Research on the edge isolation process of typical polycrystalline silicon solar cells was carried out using laser scribing equipment. The voltage-current characteristics of the solar cell before and after laser scribing were analyzed using a solar simulator. Current density and efficiency increased as the fill factor of the solar cell remained constant after the laser scribing process. The efficiency of the solar cell can be increased in a short time by the edge isolation process performed via a laser scribing process. The polycrystalline silicon solar cell was made into a series electrode, and the efficiency of the solar cell increased because the width of the solar cell was narrowed and the active region was widened by the laser scribing process.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.2
• /
• pp.55-62
• /
• 1992

Polycrystalline silicon ingots were manufactured using the casting method for polycrystalline silicon solar cells. These ingots were cut into wafers and ten n$^{+}$p type solar cells were made through the following simple process` surface etching, n$^{+}$p junction formation, metalization and annealing. For the grain boundary passivation, the samples were oxidized in O$_2$ for 5 min. at 80$0^{\circ}C$ prior to diffusion in Ar for 100 min. at 95$0^{\circ}C$. The conversion efficiency of polycrystalline silicon solar cells made from these wafers showed about 70-80% of those of the single crystalline silicon solar cell and superior conversion efficiency, compared to those of commercial polycrystalline wafers of Wacker Chemie. The maximum conversion efficiency of our wafers was indicated about 8%(without AR coating) in spite of such a simple fabrication method.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1430-1432
• /
• 1997

A solar cell conversion effiency was degraded by grain boundary effect in polycrystalline silicon. To reduce these effects of the grain boundaries, we investigated various influencing factors such as preferential chemical etching of grain boundaries, grid design, transparent conductive thin film, and top metallization along grain boundaries. Pretreatment in $N_2$ atmosphere and gettering by $POCl_3$ and Al were performed to obtain polycrystalline silicon of the reduced defect density. Structural, electrical, and optical properties of solar cells were characterized. Improved conversion efficiencies of solar cell were obtained by a combination of Al diffusion into grain boundaries on rear side, fine grid finger, top Yb metal grid on Cr thin film of $200{\AA}$ and buried contact metallization along grain boundaries.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.49.1-49.1
• /
• 2010

본 연구에서는 증착법에 의해 제조된 다결정 실리콘을 이용한 태양전지 제작과 관련하여 다결정 실리콘 씨앗층 제조를 위한 기판에 대하여 연구를 수행하였다. 다결정 실리콘 씨앗층을 제조할 수 있는 기술중 aluminum-induced layer exchange(ALILE) 공정을 이용하여 다결정 실리콘 씨앗층을 제조하였다. glass/Al/oxide/a-Si 구조로 알루미늄과 비정질 실리콘 계면에 알루미늄 산화막을 다양한 두께로 형성시켜, 알루미늄 유도 결정화에서 산화막의 두께가 결정화 특성에 미치는 영향, 결정결함, 결정크기에 대하여 연구하였다. 형성된 다결정 실리콘 씨앗층 막의 특성은 OM, SEM, FIB, EDS, Raman spectroscopy, XRD, EBSD 을 이용하여 분석하였다. 그 결과 산화막의 두께가 증가할수록 결함도 함께 증가하였다. 16nm 두께의 산화막 구조에서 <111> 방향의 우선배향성을 가진, $10{\mu}m$의 sub-grain 결정립을 갖는 씨앗층을 제조 하였다.

• Electrical & Electronic Materials
• /
• v.10 no.10
• /
• pp.1034-1040
• /
• 1997

A solar cell conversion effiency was degraded by grain boundary effect in polycrystalline silicon. Grain boundaries acted as potential barriers as well as recombination centers for the photo-generated carriers. To reduce these effects of the grain boundaries we investigated various influencing factors such as emitter thickness thermal treatment preferential chemical etching of grain boundaries grid design contact metal and top metallization along boundaries. Pretreatment in $N_2$atmosphere and gettering by POCl$_3$and Al were performed to obtain multicrystalline silicon of the reduced defect density. Structural electrical and optical properties of slar cells were characterized before and after each fabrication process. Improved conversion efficiencies of solar cell were obtained by a combination of pretreatment above 90$0^{\circ}C$ emitter layer of 0.43${\mu}{\textrm}{m}$ Al diffusion in to grain boundaries on rear side fine grid finger top Yb metal and buried contact metallization along grain boundaries.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.964-967
• /
• 2002

The effectiveness of silicon nitride SiNx surface passivation is investigated and quantified. This study adopted single-layer antireflection (SLAR) coating of SiNx for efficiency improvement of solar cell. The silicon nitride films were deposited by means of plasma enhanced chemical vapor deposition (PECVD) in planar coil reactor. The process gases used were pure ammonia and a mixture of silane and helium. The thickness and the refractive index on the films were measured by ellipsometry and chemical bonds were determined by using an FT-IR equipment. This films obtained were analyzed in term of hydrogen content, refractive index for gas flow ratio $(NH_3/SiH_4)$, and efficiency of solar cell. The polycrystalline silicon solar cells passivated by silicon nitride shows efficiency above 12.8%.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.232-232
• /
• 2007

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.78-81
• /
• 1994

The Photovoltaics(PV) industry has been evolving over the last 30 years and expanding because of a rising demand for clean and safe energy. Crystalline silicon solar cells will have increased performance and reduced cost in the future. In this paper solution growth process used to fabricate polycrystalline silicon thin film is considered.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.19 no.5
• /
• pp.38-42
• /
• 1982

N+-P/P+solar cells were fabricated by using the polycrystalline silline wafer with the resistivity of 3-6 ohm-cm. minority carrier lifetimes, measured by Nd: YAG laser, were from 100ns up to 150ns. Conversion efficiency measured under AM 1 irradiation, were about 4%.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.27 no.7
• /
• pp.375-379
• /
• 2015

A proper estimate of solar cell efficiency is of great importance for the feasibility analysis of solar cell power plant development. Since solar cell efficiency depends on temperature, several methods have been introduced to measure it by operating temperature modulation. However, the methods either rely on the external environment or need expensive equipment. In this paper, a thermoelectric module was used to control the operating temperature of crystalline silicon solar cells effectively and precisely over a wide range. The output characteristics of crystalline silicon solar cells in response to operating temperatures from $-5^{\circ}C$ to $100^{\circ}C$ were investigated experimentally. Their efficiencies decreased as the temperature rose, since the decrease in the open circuit voltage and fill factor exceeded the increase in the short circuit current. The maximum power temperature coefficient of the single crystalline solar cell was more sensitive to temperature change than that of the polycrystalline solar cell.