• Korean Journal of Materials Research
• /
• v.15 no.11
• /
• pp.745-750
• /
• 2005

Polycarbonates are widely used as housing materials of electronic handsets. Since the polycarbonate is electrically insulating, there should be a conducting layer on the polycarbonate for EMI shielding. In this study, we sputter deposited Cu films on the polycarbonate substrates for EMI shielding. Plasma treatments of polycarbonates were used to increase the adhesion strength of the Cu film/polycarbonate interface. The surface energy of the polycarbonate was greatly increased from $30mJ/m^2 \;to\; 65mJ/m^2$ by a 200 W $O_2$ plasma treatment for 10s. It is thought that this is because of the ion bombardment. The adhesion strength of the sputter deposited Cu film to the polycarbonate was quantitatively measured by a 4 point bending tester. A moderate plasma surface treatment of the polycarbonate increased the Cu film/polycarbonate adhesion strength by $30\%$. The EMI shielding efficiency of the sputter deposited $10{\mu}m$ Cu lam on the polycarbonate showed 90dB in the range of 100MHz to 1000MHz.

• Applied Chemistry for Engineering
• /
• v.25 no.1
• /
• pp.41-46
• /
• 2014

The property improvement of polycarbonate coated with a multilayer film composed of an inorganic $SiO_2$ film and a photocatalytic $TiO_2$ film was studied. The $SiO_2$ film as a binder had an excellent light transmission characteristic. After the treatment with atmospheric pressure plasma, the surface of $SiO_2$ film showed the hydrophilicity, which increased the film coating uniformity with a $TiO_2$-containing aqueous solution. When $TiO_2$ film was over 200 nm thick, the absorption effect of UV rays in the range of 180~400 nm suppressed the yellowing phenomena of polycarbonate substrate. The inorganic film improved the heat resistance of polycarbonate substrates. $TiO_2$ film in the outmost under the exposure of UV rays promotes the catalytic oxidation characteristics and yields the capability to the decomposition of organic contaminants, and also increases the self-cleaning properties due to the increase of hydrophilicity. Structural stability of the polycarbonate substrate coated with inorganic $TiO_2$ and $SiO_2$ film was shown. The role of $SiO_2$ film between $TiO_2$ and polycarbonate substrate suppressed the peeling of $TiO_2$ film by inhibiting the photocatalytic oxidation effect of $TiO_2$ film on the polycarbonate substrate.

• Journal of Satellite, Information and Communications
• /
• v.12 no.2
• /
• pp.11-14
• /
• 2017

In this paper, we introduce a method of light focusing effect using prism structure to solve optical discontinuity of conventional external signage LED panels. The prims structures were patterned on a transparent polycarbonate substrate with MEMS and femto-second laser process. We have confirmed that the patterned prism structures on the substrate made artificial LED lights on empty space between the panels by light guide effect of the structure. The artificial light's lateral positions were controlled by thickness of polycarbonate substrate. This cost effective prim patterned transparent film can be utilized on digital signage LED panels to achieve good optical communication.

• Journal of Satellite, Information and Communications
• /
• v.11 no.1
• /
• pp.51-54
• /
• 2016

This paper present a method which resolves an optical discontinuity in bezel of digital signage using light guide film. On a polycarbonate film, a light guide film is bonded to produce refraction, reflection, diffraction of light. Arc shaped light guide film is assembled on the top LED light sources (red and green) to see light propagation through the film. When the two light sources (red and green) are mechanically attached at the end of the film, optical convergence brings new colors which have light wavelength between red and green. This result indicates that the light waveguide method could solve the light discontinuity on bezel of the digital signage system.

• Polymer(Korea)
• /
• v.32 no.5
• /
• pp.478-482
• /
• 2008

The effect of 1,3-dioxolane on the structural development in the optical polycarbonate film was studied. The 1,3-dioxolane was used as an environmental friendly solvent for manufacturing solution-cast polycarbonate film instead of methylene chloride. The evaporation rate in film drying process decreased due to the high boiling temperature of 1,3-dioxolane. This caused the crystallization in the polycarbonate film. As a result, The increase of crystallinity and roughness led to the decrease of light transmissivity. It was also found that the lowering of mechanical properties in polycarbonate film was attributed to the morphological change due to the solvent evaporation rate in film drying process.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.169-170
• /
• 2011

• Nuclear Engineering and Technology
• /
• v.8 no.1
• /
• pp.9-17
• /
• 1976

Dosimetrical properties of polycarbonate film for high-level dosimetry of electrons have been examined. Polycartonate film of 0.1mm in thickness was chosen for this purpose. It can cover the dose range of 1.0-130 Mrad and the measurable range can be extended up to 200 Mrad by using calibration curve. The measurement error was within 3.5%. The radiation induced optical density at 330nm shows rapid initial fading of 7-l3n for one day after irradiation at room temperature and subsequent fading rate is very small, about 0.6% per day. The fading depends on the absorbed dose, storage temperature, and wavelengths. The effects of storage time and temperature during and after irradiation of this film are presented. For practical dosimetry, it is necessary to stabilize the induced optical density by storing the irradiated film for a day or by heat treatment at 10$0^{\circ}C$ for an hour.

• Applied Chemistry for Engineering
• /
• v.10 no.2
• /
• pp.287-292
• /
• 1999

The conducting composites were prepared by solution blending of polyaniline (PANI) as a conducting polymer and polycarbonate (PC) as a matrix in chloroform. Also the composites film was prepared by solution casting method. The PANI was protonated with alkylbenzenesulfonic acids, such as camphorsulfonic acid (CSA) or dodecylbenzenesulfonic acid (DBSA). The electrical conductivity of composites prepared by solution casting was enhanced compared with that of compression molding. The electrical conductivity, tensile strength and morphology were observed as a function of the amount of protonating agent as well as PANI complex content. In general, as the PANI complex content was increased, the electrical conductivity increased. In the case of the composite film containing 25 wt % of PANI complex doped with DBSA, the electrical conductivity exhibited 3.18 S/cm.

• Polymer(Korea)
• /
• v.29 no.6
• /
• pp.588-592
• /
• 2005

For the purpose of obtaining polycarbonate film which blocks ultra-violet ion beam was irradiated onto the surface of PC film. This method has gotten several advantages compared with the techniques, such as the protection of changes in film thickness and UV blocking material deposited onto a base film. In order to investigate UV blocking PC film, the optical and chemical characteristics, surface morphology and lightfastness were confirmed by UV/Vis, FTIR(ATR) spectroscopy, AFM, and Q-UV fasoess analyses. As a result, it was shown that the modified PC film was able to block almost all of UV region and easily control the degree of UV block. The optical changes in the film were attributed to chemical changes in PC surface by ion beam irradiation. Moreover, we expect that the modified PC film can durably block UV due to no changes in colour and UV transmittance after UV fastness test.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.108-109
• /
• 2009

In this study we investigated the characteristics of GZOB thin film on $O_2$ plasma treated Polycarbonate substrate using DC magnetron sputtering method. In our experiments results, GZOB thin film on $O_2$ plasma treated Polycarbonate substrate showed low resistivity than As-grown GZOB thin film, and visible transmission of 85% with a thickness 400 nm. Compared with As-Grown the electrical properties of GZOB were relatively improved by $O_2$ plasma treated substrate. From these results, we could confirm the suitable GZOB thin films for transparent electrode.