• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12
• /
• pp.1091-1096
• /
• 2003

Ion implantation in polymeric materials can induce dramatic chemical modifications, such as bond breaking, cross linking, formation of new chemical products, which have strong influences on the macroscopic properties of the materials. In this study ion implantation was performed onto polymer, PC(polycarbonate), in order to investigate change of the optical transmittance property focusing ultraviolet ray range(200-400nm). PC was irradiated with N, Ar, Kr, Xe ions at the ion energy of 50keV and the dose range of 5 ${\times}$ 10$\^$15/, 1 ${\times}$ 10$\^$16/, 7${\times}$10$\^$16/ ions/$\textrm{cm}^2$. FT-IR, XPS, UV/Vis transmittance spectroscopy measurement technologies were employed to obtain chemical. structural properties and optical transmittance of irradiated polymer. The original PC(unimplanted) is quite transparent that it has more than 88% transmittance in the range UV-A(320∼400nm), but after ion implantation, surface colors were changed to the dark brown and the transmittance of UV ray decreased for all implantation condition, and the absorption edge was shift to visible range with increasing mass of implanted ion species and dose.

• Korean Chemical Engineering Research
• /
• v.47 no.3
• /
• pp.316-320
• /
• 2009

UV curable hard and color coatings were formed on polycarbonate(PC) films. The coating materials were composed of a commercially available end-capped polyester(EB830), diacrylate monomer(HDDA), silicon acrylate, photoinitiator, and organic dye as a coloring agent. The surface properties of coating films were evaluated, and the influences of the compositions of coating materials were investigated. The coating films showed high transmission and good adhesion between coating layer and PC substrate. And the coating films exhibited higher hardness than bare PC film. The coating films with various colors were obtained by wet process, and the clear and color window lenses for mobile phone were prepared successfully.

• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.1
• /
• pp.26-32
• /
• 1990

This study investigated a method for the determination of the J-integral for a tough glassy polymer such as polycarbonate plates by using the method of caustics. Comparing the values of J-integral determined by a numerical analysis and by the method of caustics, the method of caustics was found to be an effective experimental technique for the determination of the J-integral. The ratio between two J-integrals determined by the method of caustics and by finite element method converged into 1 within the limit of low load. However, it was noticed that the greater the plastic zone at the crack tip was, the lower the J-integral obtained by the reflect method of caustics. This difference may be deduced from the damage at the crack tip such as craze appeared in the polycarbonate plate. It was confirmed that the ratio of longitudinal diameter( $D_{l}$ ) to transverse diameter ( $D_{t}$) of caustics generally converged into 1 at the low load. The transition of the state of stress at the vicinity of a crack tip from plane strain to plane stress was deduced by noticing that the longitudinal diameter( $D_{l}$ ) grew faster than the transverse diameter( $D_{t}$) of caustics within the higher load range.

• Macromolecular Research
• /
• v.10 no.3
• /
• pp.135-139
• /
• 2002

Blends of the linear bisphenol-A polycarbonate (L-PC) and randomly branched bisphenol-A polycarbonate (Br-PC), prepared by co-rotating twin screw extrusion, were investigated using differential scanning calorimetry (DSC), sag resistance time tester, extensional rheometry, and advanced rheometric expansion system (ARES). From the DSC results, the glass transition temperature (T$_{g}$) of the L-PC/Br-PC blend was increased with the increase of Br-PC in the blend, and the blend showed a single T$_{g}$, which suggests a miscible blend. The sag resistance time of the L-PC/Br-PC blend was increased with the increase of Br-PC in the blends. From the results of rheological measurements of the L-PC/Br-PC blends, the extensional viscosity and the complex viscosity of the blends were found to increase with the increase of Br-PC in the blends. The increase of extensional viscosity and complex viscosity was related with the increase of sag resistance time with the Br-PC in the L-PC/Br-PC blends.nds.

• Macromolecular Research
• /
• v.15 no.7
• /
• pp.640-645
• /
• 2007

The phase behavior of branched polycarbonate (BPC) blends with poly(ethylene terephthalate-co-1,4-dimethyl cyclohexane terephthalate) copolyesters (PECT), as well as their rheological properties, were assessed. Even though BPC blends with PECT prepared by solvent casting proved to be immiscible, BPC and PECT copolyesters containing 1,4-dimethyl cyclohexane (CHDM) from 32 to 80 mole% formed homogeneous mixtures upon heating. The homogenization temperatures of the blends decreased with increasing CHDM content in PECT. The interaction energies of the BPC-PECT pairs calculated from the phase boundary in accordance with the lattice-fluid theory were positive and also decreased with increasing CHDM content in PECT. It was shown that the phase homogenization of these blends occurs upon heating when the combinatorial entropy term, which is favorable for miscibility, overcomes unfavorable energetic terms at elevated temperatures. A novel product, which is not limited by the drawbacks of linear polycarbonate (PC) and evidences processability superior to that of the PC/PECT blends, can be developed via the blending of BPC and PECT.

• Macromolecular Research
• /
• v.9 no.3
• /
• pp.129-142
• /
• 2001

To efficiently demonstrate the molecular motion, physical properties, and mechanical properties of polycarbonates, we studied the differences between bisphenol-A polycarbonate(BPA-PC) and tetramethyl bisphenol-A-polycarbonate(TMBPA-PC) using molecular modeling techniques. To investigate the conformations of BPA-PC and TMBPA-PC and the effect of the conformation on mechanical properties, we performed conformational energy calculation, molecular dynamics calculation, and stress-strain curves based on molecular mechanics method. From the result obtained from conformational energy calculations of each segment, the molecular motions of the carbonate and the phenylene group in BPA-PC were seen to be more vigorous and have lower restriction to mobility than those in TMBPA-PC, respectively. In addition, from the results of radial distribution function, velocity autocorrelation function, and power spectrum, BPA-PC appeared to have higher diffusion constant than TMBPA-PC and is easier to have various conformations because of the less severe restrictions in molecular motion. The result of stress-strain calculation for TMBPA-PC seemed to be in accordance with the experimental value of strain-to-failure ∼4%. From these results of conformational energy calculations of segments, molecular dynamics, and mechanical properties, it can be concluded that TMBPA-PC has higher modulus and brittleness than BPA-PC because the former has no efficient relaxation mode against the external deformations.

• Journal of Adhesion and Interface
• /
• v.9 no.3
• /
• pp.1-6
• /
• 2008

Hard coatings were deposited on a polycarbonate plate as potential substitutes for glass in cars. In this research the copolymers of p-polyphenylene (PPH) and m-phenylene (MPH) were synthesized, and using these copolymers the coatings were conducted on a polycarbonate plate. The hardness of the coating surface was affected with the mole ratio of PPH and MPH in the copolymer. When the mole ratio of PPH : MPH in the copolymer was 20 : 80, the coating showed 2H class of pencil hardness and also showed the best abrasion resistance.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.7
• /
• pp.19-25
• /
• 2014

In the LED lighting applications, because LED packages are the origin of heat generation, there are thermal design problem on heat sinks. In the thermal design, it is important to consider the total volume and the total weight of heat sink simultaneously. In this study, an Al 6063 heat sink was optimized using Computational Fluid Dynamics(CFD) simulation tool for the cooling of 30W LED module, and then the cooling performance and the total weight of heat sinks with Al 6063 and Thermal Conductive Polycarbonate(TCP) were compared under the same conditions. As the result of simulation, an Al 6063 heat sink was optimized with 22 ea. of fins and 1.6 mm of fin thickness. LED Junction Temperature of the TCP Heat Sink was $5.6^{\circ}C$ higher, but total weight of it was 47 % less than the Al 6063.

• Polymer(Korea)
• /
• v.32 no.5
• /
• pp.427-432
• /
• 2008

Hard coatings were deposited on a polycarbonate plate as potential substitutes for glass in cars. In this research polyphenylene derivatives were synthesized and the coatings were conducted on a polycarbonate plate. Poly(benzoylphenylene) and its phenylene copolymers were synthesized. Using poly (benzoylphenylene), the coating showed 1H class of pencil hardness. And using its copolymers, the coating showed 2H class of pencil hardness. The copolymer also showed the better abrasion resistance than homopoly (benzoylphenylene).

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.10
• /
• pp.59-67
• /
• 2020

Polycarbonate thermoplastic composite materials are anisotropic and exhibit physical properties in the longitudinal direction. Therefore, the physical properties depend on the type and direction of reinforcements. The thermal conductivity, electrical conductivity, and resin impregnation can be controlled by adding carbon nanotubes to polycarbonate resin. However, the carbon fiber used as a reinforcing material is expensive, interfacial adhesion issues occur, and simulation values are different from actual values, making it difficult to perform mathematical analysis. However, carbon nanotubes have advantages such as light weight, rigidity, impact resistance, and reduced number of parts compared to metals. Due to these advantages, it has been applied to various products to reduce weight, improve corrosion resistance, and increase impact durability. As the content of carbon nanotubes or carbon fibers increases, the mechanical properties and antistatic and electromagnetic shielding performance improve. It is expected that the amount of carbon nanotubes or carbon fibers can be optimized and applied to various industrial products.