• Journal of Hydrogen and New Energy
• /
• v.30 no.6
• /
• pp.567-577
• /
• 2019

Due to the depletion of fossil fuels and environmental pollution, demand for alternative energy is gradually increasing. Among the various methods, a method to convert biomass into alternative fuel has been proposed. The bio-fuel obtained from biomass through pyrolysis process is called pyrolysis oil (PO) or bio-oil. Because PO is difficult to use directly in conventional engines due to its poor fuel properties, various methods have been proposed to upgrade pyrolysis-oil. The simplest approach is to mix it with conventional fossil fuels. However, due to their different polarity of PO and fossil fuel, direct mixing is impossible. To resolve this problem, emulsification of two fuels with a proper surfactant was proposed, but it costs additional time and cost. Alternatively, the use of alcohol fuels as an organic solvent significantly improve the fuel properties such as fuel stability, calorific value and viscosity. In this study, blends of diesel, n-butanol, and coffee ground pyrolysis oil (CGPO) which is one of the promising PO, was applied to diesel generator. Combustion and emissions characteristics of blended fuels were investigated under the entire load range. Experimental results show that ignition delay is similar to that of diesel at high load. Although, hydrocarbon and carbon monoxide emissions are comparable to diesel, significant reduction of nitrogen oxides and particulate matter emissions were observed.

• Journal of Environmental Science International
• /
• v.16 no.11
• /
• pp.1225-1230
• /
• 2007

The emissions characteristics of particulate matters(PM) according to the types of wastes from industrial waste incinerator of 800 kg/hr treatment capacity were investigated. For this study, the incinerate waste are as follows; waste resin, waste wood, waste urethane, waste gunny, and waste paper. The particulate samples were collected to be emitted in stack and air pollution control(both cyclone and bag filter). In stack, the concentrations of PM were in the range of 2.61 to $26.51 mg/Sm^3$ and the major chemical species were C, Si, Cl, K, Na, Ca in all the wastes. In cyclone fly ash, the mean content of heavy metal were in the order of Fe > Zn > Pb > Cu > Mn > Cr > Ni > Cd > As > Hg and the heavy metal content of waste resin were Zn 34,197.5 mg/kg, Fe 27,587.6 mg/kg, Pb 6,055.8 mg/kg, respectively. In bag filter fly ash, the mean content of heavy metal were in the order of Zn > Pb > Fe > Cu > Mn > Cd > Cr > Ni > As > Hg and the heavy metal content of waste wood were Pb 36,405.2 mg/kg, Fe 15,762.9 mg/kg, Cu 9,989.5 mg/kg, Cd 2,230.1 mg/kg, respectively. Comparing the heavy metal content of both cyclone and bag filter, in cyclone, the Cr, Fe, Ni content were higher than in bag filter and the Cd, Cu, Hg content were lower than in bag filter.

• Journal of Environmental Health Sciences
• /
• v.31 no.4 s.85
• /
• pp.301-308
• /
• 2005

The purpose of this study was to characterize mass concentration of $PM_{10}\;to,\;PM_{2.5}$ and metallic composition using Minivol Portable Sampler from May 2003 to May 2004 in metropolitan city, Seoul. Annual average concentration of $PM_{10}$ were $57.67({\pm}28.20)\;{\mu}g/m^3\;and\;PM_{2.5},\;were\;42.06({\pm}20.23)\;{\mu}g/m^3$. The concentration was the highest in winter because persistent thermal inversion and in spring, particulate matter concentration was high because of yellow-sand events. The average $PM_{2.5}/PM_{10}$ ratio was 0.73. This indicated $PM_{2.5}$ fraction played a significant role in air pollution. The atmospheric metallic elements in the $PM_{10},PM_{2.5}$ came different emission sources such as soil, traffic, industry and resuspended particles. The results showed that average $PM_{10}$ composition order as Fe>Zn>Pb>Cu>Mn. The metallic elements Zn and Fe were the largest composition in the $PM_{2.5}$

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.6
• /
• pp.417-421
• /
• 2018

$TiO_2$ has excellent photocatalytic properties and several studies have reported the increase in its specific surface area. The structure of $TiO_2$ nanofibers indicates promising improved photocatalytic properties and these nanofibers can thus potentially be applied in air pollution sensors and pollutant removal filters. In this study, a $TiO_2$ nanofiber was fabricated by the electrospinning method. The fabrication processing factors such as the applied voltage, the distance between nozzle and collector, and the inflow rate of solution were controlled. The precursor was titanium (IV) isopropoxide and as-spun $TiO_2$ nanofibers were heated at $450^{\circ}C$ for 2 h to obtain an anatase crystalline structure. The microstructure was analyzed using field emission scanning electron microscope (FE-SEM) and X-ray diffraction analysis (XRD). The anatase phase was observed in the $TiO_2$ nanofibers after heat treatment. The diameter of $TiO_2$ nanofibers increased with the flow rate, but decreased with decreasing applied voltage and nozzle to collector distance. The diameter of $TiO_2$ nanofibers was controlled in the range of 364 nm to 660 nm. These nanofibers are expected to be very useful in photocatalytic applications.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.1
• /
• pp.17-24
• /
• 2004

As the environmental pollution becomes serious global problem, the regulation of emission exhausted from automobiles is strengthened. Therefore, it is very important to know how to reduce the NOx and PM simultaneously in diesel engines, which has lot of merits such as high thermal efficiency, low fuel consumption and durability. By this reason, the new concept called as Homogeneous Charge Compression Ignition(HCCI) engines are spotlighted because this concept reduced NOx and P.M. simultaneously. However, it is well known that HCCI engines increased HC and CO. Thus, the investigation of combustion characteristics which consists cool and hot flames for HCCI engines were needed to obtain the optimal combustion condition. In this study, combustion characteristics for direct injection type HCCI engine such as quantity of cool flame and hot flame, ignition timing and ignition delay were investigated to clarify the effects of these parameters on performance. The results revealed that diesel combustion showed the two-stage ignition of cool flame and hot flame, the rate of cool flame increase and hot flame decrease with increasing intake air temperature. On the other hand, the gasoline combustion is the single-stage ignition and ignition timing is near the TDC. In addition mixed fuel combustion showed different phenomenon, which depends on the ratio of gasoline component. Ignition timing of mixed fuel is retarded near the TDC and the ignition delay is increased according to ratio of gasoline.

• International Journal of Highway Engineering
• /
• v.18 no.1
• /
• pp.119-129
• /
• 2016

PURPOSES : The purpose of this study is to develop a methodology for estimating additional carbon emissions due to freeway incidents. METHODS : As our country grows, our highway policy has mainly neglected the environmental and social sectors. However, with the formation of a national green growth keynote and an increase in the number of people interested in environmental and social issues, problems related to social issues, such as traffic accidents and congestion, and environmental issues, such as the impact of air pollution caused by exhaust gases that are emitted from highway vehicles, are beginning to be discussed. Accordingly, studies have been conducted on a variety of environmental aspects in the field of road transport, and for the quantitative calculation of greenhouse gas emissions, using various methods. However, in order to observe the effects of carbon emissions, microscopic simulations must use many difficult variables such as cost, analysis time, and ease of analysis process. In this study, additional greenhouse gas emissions that occur because of highway traffic accidents were classified by type (incident handling time, number of lanes blocked, freeway level of service), and the annual additional emissions based on incidents were calculated. According to the results, congestion length and emissions tend to increase with an increase in incident clearance time, number of occupied lanes, and worsening level of service. Using this data, we analyzed accident data on the Gyeong-bu Expressway (Yang-Jae IC - Osan IC) for a year. RESULTS : Additional greenhouse gas emissions that occur because of highway traffic accidents were classified by type (incident handling time, number of lanes blocked, freeway level of service) and annual additional emissions caused by accidents were calculated. CONCLUSIONS : In this study, a methodology for estimating carbon emissions due to freeway incidents was developed that incorporates macroscopic flow models. The results of the study are organized in the form of a look-Up table that calculates carbon emissions rather easily.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.440-440
• /
• 2012

본 연구에서는 수질관리 및 기후변화(온실가스 저감) 등에 부응할 수 있는 SRI 벼재배 방법을 국내 논에 적용하여 농업비점오염원과 온실가스 저감효과를 측정하고 비교하여 SRI의 환경개선효과를 평가하고자 하였다. 시험포는 대조구인 상시담수처리구(관행, 재식거리 $30{\times}15cm$)와 SRI 물관리 처리구로 조성하였다. 각 시험포에는 관개배수시설 및 관개량을 측정할 수 있는 수도계량기, 유출량 측정을 위한 플륨 및 수위계 그리고 온실가스(메탄 및 이산화질소)를 측정하기 위한 아크릴재질의 Chamber를 설치하였다. 관행 및 SRI 시험포에 이앙할 모의 재배품종으로 오대벼를 공시하고 모든 시험포의 경우 1주당 3-5본씩 기계이앙을 실시하였으며, 물관리를 제외한 시비와 제초 등의 영농관리는 동일하게 수행하였다. 메탄($CH_4$)과 아산화질소($N_2O$)는 주 2회, 오전 9시 12시에 60 mL 주사기로 주기적으로 시료를 채취하여 GC로 분석하였다. 그리고 관개기간동안 관개량, 강우량 그리고 강우 유출량을 측정하고 수질시료를 채취하여 오염부하를 산정하였다. SRI 시험포의 SS, $COD_{Cr}$, $COD_{Mn}$, BOD, TN, TP의 총 오염부하량은 각각 583 kg/ha, 210.8 kg/ha, 70.1 kg/ha, 30.7 kg/ha, 56.1 kg/ha, 3.55 kg/ha로서 관행 시험포의 오염부하량에 비해 27.1~46.0%의 오염물질 저감 효과를 보였다. 그리고 각 시험포별 온실가스 메탄과 아산화질소의 총 배출량을 지구온난화잠재력(GWP)으로 환산하여 이산화탄소($CO_2$) 기준으로 산정한 결과, 관행은 14.2 톤/ha 그리고 SRI 물관리 처리구 4.0 톤/ha로 관행 대비 SRI 처리구에서 71.8%의 온실가스 감축효과를 나타내었다. 따라서 SRI 벼재배기술은 논 비점오염부하 및 온실가스 저감을 위한 효과적인 최적영농관리방법인 것으로 판단된다.

• Journal of Korean Society on Water Environment
• /
• v.21 no.3
• /
• pp.248-255
• /
• 2005

Since the water quality of drinking water sources has been recognized as a big issue, the ministry of Environment in Korea is designing the total maximum daily load (TMDL) program for 4 major large rivers. The TMDL program can be successfully performed as controling the nonpoint pollutants from watershed area near the river. Of the various landuses in nonpoint pollution, parking lots and bridges are stormwater intensive landuses because of high imperviousness and high pollutant mass emissions from vehicular activities. Vehicle emissions from those areas include different pollutants such as heavy metals, oil and grease and particulates from sources such as fuels, brake pad and tire wear, etc. Especially the pollutant washed-off from the landuses are directly affecting to the river water quality. Therefore this research was conducted to understand the magnitude and nature of the stormwater emissions with the goal of quantifying stormwater pollutant concentrations and mass emission rates of pollutants from parking lot and bridges in Korea. In Kongju city areas, two monitoring sites were equipped with an automatic rainfall gages and an automatic flow meter for accumulating the useful data such as rainfall, water quality and runoff flow. This manuscripts will show the concentration changes during storm duration and EMCs to characterize the concentration profiles in different land uses. Also the first flush criteria will be suggested using dynamic EMCs. The definition of dynamic EMC is a new approach explaining the relationship of EMC and first flush effect.

• Journal of Korean Society on Water Environment
• /
• v.20 no.3
• /
• pp.215-222
• /
• 2004

The sewages produced from small villages, rural community, drinking water reservation area and park which doesn't have sewage piping system can be caused a serious water pollution at the restricted areas. The objective of this research was to suggest an economical and effective sewage treatment method by investigating the removal of the organics, nitrogen, and phosphorus in the multi-soil-layering reactor. Soil, natural zeolite, and iron slag were used as a supporting media of multi-soil-layering in this research. The purpose of natural zeolite addition was to maintain the consistent ammonium exchange capacity by providing a sequential environment, and that of iron slag addition was to remove phosphorus by adsorption. Continuous experiment of lab-scale single-soil-layering (S-1), multi-soil-layering (S-2), and mixed-soil-layering (S-3) methods were studied to compare and optimize three different types of the reactors. The organic removal efficiencies showed more than 90% in all three reactors. While S-1 and S-3 reactors showed about T-N removal of 31%, 45%, respectively, the average T-N removal efficiency of the S-2 reactor represented an 87%. In conclusion, that results suggest that the multi-soil-layering reactor could be effectively utilized as a plant for treatment of small village sewage.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.63 no.3
• /
• pp.97-105
• /
• 2021

Most of the rural development projects for the welfare of residents are mainly new construction and remodeling projects for community buildings such as village halls and senior citizens. However, in the case of the construction industry, it has been studied that 23% of the total carbon dioxide emissions generated in Korea are generated in the building-related sector. (GGIC, 2015) In order to reduce the emission of environmental pollutants resulting from construction of rural community buildings, there is a need to establish a system for rural buildings by predicting the environmental impact. As a result of this study, the emissions of air pollutants from buildings in rural communities were analyzed by dividing into seven stages: material production, construction, operation, maintenance, demolition, recycling, and transportation activities related to disposal. As a result, 12 kg of carbon dioxide (CO), 0.06 kg of carbon monoxide (CO), 0.02 kg of methane (CH), 0.04 kg of nitrogen oxides (NO), 0.02 kg of sulfurous acid gas (SO), and non-methane volatile organics per 1m of buildings in rural communities It was analyzed that 0.02 kg of compound (NMVOC) and 0.00011 kg of nitrous oxide (NO) were released. This study proved that environmentally friendly design is possible with a quantitative methodology for the comparison of operating energy and air pollutant emissions through the design specification change based on the statement of the rural community building. It is considered that it can function as basic data for further research by collecting major structural changes and materials of rural community buildings.