• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.18 no.1
• /
• pp.22-28
• /
• 2009

In order to optimize the polishing process, Run to Run control scheme has been applied to the micro mold polishing in this study. Also, to fully understand the effect of parameters on the surface roughness a design of experiment is performed. By linear approximation of main factors such as gap and rotational speed of micro quill, EWMA (Exponential Weighted Moving Average) gradual mode controller is adopted as a optimizing tool. Consequently, the process converged quickly at a target value of surface roughness Ra 10nm and Rmax 50nm, and was hardly affected by unwanted process noises like initial surface quality and wear of magnetic abrasives.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.3
• /
• pp.324-330
• /
• 2013

This paper describes a novel method to surface large optics mirror with an extremely high hardness, which could replace the high cost of the repetitive off-line measurement steps and the large ultra-precision grinding machine with ultra-positioning control of 10 nm resolution. A lot of diamond pellet to be attached on the convex aluminum base consists of a grinding tool for the concave large mirror, and the tool was pressured down on the large mirror blank. The tool motion at an interval on the spiral path was controlled with each feed rate as the dwell time in the conventional computer-controlled polishing. The shape to be surfaced was measured directly by a touch probe on the machine without any separation of the mirror blank. Total 40 iterative steps of the surfacing and measurement could demonstrate the form error of RMS $7.8{\mu}m$, surface roughness of Ra $0.2{\mu}m$ for the mirror blank with diameter of 1 m and spherical radius of curvature of 5400 mm.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.137-138
• /
• 2010

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.4
• /
• pp.334-343
• /
• 2001

Polishing a die that has free-form surfaces is a time-consuming and tedious job, and requires a considerable amount of high-precision skill. Some workers tend to gradually avoid the polishing work because of the poor environment caused by dust and noise. In order to reduce the polishing time and cope with the shortage of skilled workers, a user-friendly automatic polishing system was developed in this research. The polishing system with five degrees of freedom is able to keep the polishing tool normal to the die surface. The polishing system is controlled by a PC-NC controller. To easily operate the developed polishing robot system, this study developed an integrated program in the Windows environment. This program consists of four modules: the polishing module, the graphic simulator, the polishing data generation module, and the teaching module. Also, the automatic teaching system was developed to easily obtain teaching data and it consists of a three dimensional joystick and a proximity sensor. The joystick is used to simultaneously drive the polishing system to an arbitrary orientation and the proximity sensor is used to obtain teaching points precisely. Also, to evaluate the stability of the driving program and the teaching system, polishing experiments of a die of saddle shape were carried out.

• Design & Manufacturing
• /
• v.11 no.2
• /
• pp.20-24
• /
• 2017

Recent industrial developments are constantly advancing, and rapid technological development is demanding high technology level in related fields. The need for polishing is increasing even more to improve quality. In order to improve the surface quality, the final finishing process or polishing process is a very important part. Research on super precise polishing method using MR fluid is actively being carried out in domestic and foreign countries. Fine magnetic abrasive grains are aligned in the direction of a magnetic force line formed by a magnetic field and serve as a brush to polish a metal surface. This method has the advantage that the shape of the tool is not fixed and is not affected by the shape of the workpiece or the machining area. We will design the electromagnets for the MR polish polishing system and apply the magnetic field analysis using the magnetic field analysis program (ANSYS). The data obtained through this process suggests an efficient method to increase the magnetic flux density important for polishing. We will investigate the influence of the Al6061-T6 specimen on the surface of the MR polishing machine based on the optimized design.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.2
• /
• pp.174-179
• /
• 2011

This paper focuses on the optimal step-over value for magnetic tool path. Since magnetic flux density is changed according to distance from center of magnetic tool. Enhanced surface roughness is also different according to change of radius. Therefore, to get a identical surface roughness on workpiece, it is necessary to find optimal tool path including step-over. In this study, response surface models for surface roughness according to change of radiuses were developed, and then optimal enhanced surface roughness for each radius was selected using genetic algorithm and simulated annealing to investigate relation between radius and surface roughness. As a result, it found that step-over value of 6.6mm is suitable for MAP of magnesium alloy.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.7
• /
• pp.65-71
• /
• 2001

The development process of the polishing system for the aspherical lens mold for opto-electronics industry is described. The system uses the method that polishing tool is scanned on the surface under PC-NC control for the aspherical lens mold. The two axes interpolation of the minimum translation mechanism is applied to give uniform working condition by motion analysis. An aspherical surface is divided into multiple sections and each dwell time is calculated from the polishing rate model based on the Preston equation. As result of form error compensation experiment, initial form error is decreased about 25% while an average value of surface roughness is also reduced successfully from 180nm to 19nm.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.2
• /
• pp.26-32
• /
• 2010

This paper reports some experimental result in grinding and polishing of silicon cathodes used in semiconductor manufacturing process. Cup shape diamond core wheels were used in experiments and the radial and tangential grinding forces were measured with surface roughness. In polishing experiments, flat type and donut type wool polishing tools were tested. The experimental results indicate that the grinding forces are proportional to the material removal rates and the surface roughness are inversely proportional to the spindle speed. The surface roughness of polished Si decreases with polishing time and higher spindle speed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.561-564
• /
• 2003

The machining technology for the removal of micro-burr has been demanded because electrode parts of electron gun have minute holes. In this study, Magnetic Assisted Polishing(MAP) is applied to remove the micro-burr instead of the contentional polishing process such as the etching and barrel. Optimal polishing conditions are selected from many experiments using the tool of the flat end slit type. On the basis of experimental results, the deburring machine for the Magnetic Assisted Polishing of electrode part is developed and its performance is evaluated.

• Journal of Powder Materials
• /
• v.8 no.1
• /
• pp.20-25
• /
• 2001

Most of mold manufacturing procedures have been automated by the introduction of NC machine tool and CAD/CAM system. But the three-dimensional surface curvature of the mold must be done by hand work of well-skilled workers. Magnetic abrasive polishing powders were investigated for surface polishing for 3D curvature. This study aims to investigate homogeneously distributed hard phase in Fe matrix and strong bonding between Fe-matrix and hard phase. The NbC powder, $B_4C$ powder and $Al_2O_3$ powder were mixed in Fe-matrix respectively. Mixed Fe-hard phase powders were compacted by press and then these were melted by plasma melting. According to SEM, XRD and OM observation, Fe-NbC magnetic abrsive powder had the most homogeneous distribution and strong bonding. As a result of magnetic polishing, the surface roughness before magnetic polishing, 1 ${\mu}m$ $R_{max}$, was reduced to 0.2 ${\mu}m$ $R_{max}$ over the entire inner surface of the tube.