• 한국농공학회지
• /
• 제34권4호
• /
• pp.69-79
• /
• 1992

To estimate soil behavior and structural characteristics under the conditions of cyclic loading, freezing & thawing and initial state, several testing was performed and obtained following results. 1.After repeated freezing and thawing processes, original soil structure was destroyed and changed to globular structure from honeycomb or tube in its structure types. Also above processes resulted increasing the soil compression strain while decreasing the failure stress in stress-strain relationship and reached the soil structure into the mode of brittle fracture. Under cyclic loading conditions, soil cluster which was originally dispersed structure colloided with each other, seperated, and finally the soil failed due to the effect of overcompaction. 2.Through the stabilization processes seperated by four steps, the structure of soil skeleton was changed to quite different globular type. The degree of compressibility of soil was decreased in the normally consolidated zone, while the strength against external load increased due to soil particle stabilization. 3.Soil stress-strain chracteristics were largely influenced by repeated up and down processes of temperature. The maximum deformation was obtained in the case of temperature between 0 10˚C by the reseon of particle cluster reformation. 4.Soil compressibility was largely influenced by the optimum moisture content. Under freezing process, swelling could be found and its magnitude was proportional to the density of soil. 5.Density of soil was decreased as increasing the number or repeated freezing and thawing processes and the largest decreasing rate was found at the first turning point from freezing to thawing cycle.

• 한국주조공학회지
• /
• 제35권4호
• /
• pp.75-79
• /
• 2015

Commercial Zr-based amorphous alloy was recycled and oxygen was introduced during the recycling process. The oxygen content can have a great effect on the glass forming ability and the mechanical properties of the alloy. Therefore, it was closely examined. The initial oxygen content in the raw material was 1,244 ppm. It was increased to 3,789 ppm in the alloy after ten recycling processes. As the recycling processes were repeated, the oxygen content increased. Specifically, after four recycling processes, it increased sharply as compared to that after three recycling processes. After ten recycling processes, the glass transition temperature (Tg) increased from 613 K to 634 K and the crystallization temperature (Tx) increased from 696 K to 706 K. On the other hand, the super-cooled liquid region (${\Delta}T=Tx-Tg$) decreased slightly from 83 K to 72 K while the reduced glass transition temperature (Trg = Tg/Tm) was 0.63, remaining constant even when the oxygen content was increased. These results indicated that the increased oxygen content deteriorated the glass forming ability. The bending strength as determined in a three-point bending test showed a sharp decrease from 3,055 to 2,062 MPa as the oxygen content was increased from 1,244 ppm to 3,789 ppm; the extension was also decreased from 3.02 to 1.74 mm. These findings meant that the alloy became brittle.

• 한국과학교육학회지
• /
• 제37권2호
• /
• pp.225-237
• /
• 2017

이 연구에서는 예비 화학 교사가 개별적으로 지필평가 문항을 제작하는 과정의 특징을 분석하였다. 이를 위하여 8명의 예비 화학 교사가 기체 법칙에 대한 6개의 지필평가 문항을 제작하는 발성 사고 과정과 개별 심층 면담 전사본을 분석하였다. 분석 결과, 예비교사들은 지필평가 문항 제작 과정에서 문항 제작 계획 단계의 체계성 부족, 수업과 평가의 상호관련성에 대한 인식 및 고려 부족, 문항 유형 결정 기준의 다양성, 문항의 행동 영역과 난이도 판별 곤란, 교사용 지도서 활용의 제한성과 교사용 지도서에 대한 오해, 검토 관점과 내용의 제한성 및 검토시기에 따른 차이점 등의 6가지 특징을 보였다. 이는 예비교사의 지필평가 문항 제작 능력을 향상시키는 방안을 모색하는 데 의미있는 시사점을 제공할 수 있다.

• 패션비즈니스
• /
• 제15권2호
• /
• pp.145-159
• /
• 2011

The study aimed to analyze the status quo of manufacturing work environment and the work clothes' clothing comfort and wearer mobility of welding and grinding work processes in the machine and shipbuilding industries in South Korea. A questionnaire survey was conducted for the study, which consisted of questions about work clothes' clothing comfort and wearer mobility according to body parts. The findings derived from the research were: the high impact levels of work environment factors on welding and grinding work processes were noise, metal fragment, superheat, toxic gas, UV ray factors. Subject workers' assessment of work clothes' clothing pressures were in the levels between 3 (i.e. moderate) and 4 (i.e. comfortable) in a range of 5-point scale. The impact levels of wearer mobility factor were high on the work processes of welding and grinding in machine and grinding in shipbuilding. While welding process in shipbuilding showed a 'moderate' wearer mobility level and this was because its work postures were uncomfortable yet the rate of the motion change was low. The consideration to develop the work clothes specialized for certain work processes should include the materials' protecting performance from the hazardous work environment factors; and work clothes' designs that provides workers with maximized clothing comfort and wearer mobility for bending or tilting postures of upper, lower and lateral body parts defined in the study.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2006년도 춘계학술대회 및 창립 30주년 심포지엄(논문집)
• /
• pp.325-330
• /
• 2006

시간지연을 갖는 적분시스템은 공정제어 중에서 레벨제어 문제에 해당되는 프로세스이다. 본 논문에서는 이 적분 시스템에 대한 PID 제어기의 최적 동조 규칙을 제안한다. 우선 PID 제어기 파라미터를 IAE, ISE, ITSE의 성능지수의 합이 최소가 되도록 RCGA를 이용하여 최적화한다. 다음으로 이로부터 또 다른 RCGA를 사용하여 일반화된 PID 제어기의 동조규칙을 유도한다. PID 제어기는 추종제어용과 외란억제용 두 가지로 구분하였으며, 시뮬레이션을 통해 기존의 방법과 비교하여 제안한 방법의 유효성을 검토한다.

• 신재생에너지
• /
• 제2권2호
• /
• pp.102-107
• /
• 2006

In Japan, research and development were undertaken on gas hydrate-side industrial processes associated with power generation system connections that may particularly be necessary to develop gas hydrated technology-based industrial systems. In so doing, data and engineering technologies useful n formulating guidelines on design of practical process were accumulated. In addition, basic research into theoretical evidence were carried out to promote and support the development of technological elements for those processes. In basic research designed to promote and support the research and development of elemental technologies, microanalyses were conducted to understand the decomposition mechanism of mixed gas hydrate. Moreover, measurement technologies that can be applied in industrial processes, such as numerical analyses and concentration measurement, were examined. Japan has developed a highly efficient gas hydrate formation process using micro-bubbles with a tubular reactor. Higher formation rate over conventional systems has been obtained by the process. As mentioned above, the technical problems were clarified and the economics were studied from a view point of the NGH technology in this study. The results can be applied for utilization and must contribute to popularization of gas hydrate production.

• 한국군사과학기술학회지
• /
• 제9권3호
• /
• pp.77-87
• /
• 2006

Micro- or nano-size particles are required to improve the combustion efficiency and stability in the case of solid explosives and propellants. The micro-structural properties of an energetic material strongly influence the combustion and explosion behavior. However, the traditional size reduction techniques, including milling, are not suitable for production of ultra-fine size particles. As an alternative to the traditional techniques, various re-crystallization processes based on supercritical fluids have recently been proposed. Supercritical fluids are fluids at temperatures and pressures above their critical point. In principle, they do not give problems of solvent contamination as they are completely released from the solute when the decompression occurs. Rapid Expansion Supercritical Solutions(RESS) and Supercritical Anti-Solvent Process(GAS/SAS) are representatives of a nano-size particle formation process of energetic materials using supercritical fluids. In this work, various fine particle formation processes using supercritical fluids are discussed and the results are presented.

• 산업공학
• /
• 제18권3호
• /
• pp.221-233
• /
• 2005

e-Manufacturing can be referred to as a system methodology enabling the integration of manufacturing operations and IT technologies to achieve objectives of an enterprise. It is recently regarded as a powerful solution to survive in a chaotic marketplace. While conducting an e-Manufacturing project, we first needed to capture collaborative processes conducted by multiple participants in order to define functions of a system supporting them. However, pervasive process modeling techniques including IDEF3, Petri nets, and UML are not sufficient for modeling collaborative processes. Therefore, we first briefly investigate several process modeling methods including aforementioned modeling methods and ARIS focusing on the collaboration point of view. Then, we propose a new modeling method referred to as Collaborative Process Modeling (CPM) to clearly describe collaborative processes. Also, we develop and illustrate a rule for transforming collaborative process models into Marked Graph models to use the analysis power of the Petri nets. Using CPM empowers us to develop collaborative process models with simple notations, understand and facilitate the realization of the collaboration, and verify models before rushing into the development.

• Korea-Australia Rheology Journal
• /
• 제13권1호
• /
• pp.37-45
• /
• 2001

Numerical simulation of coextrusion process of viscoelastic fluids within a die has been carried out. In the coextrusion process velocity profile at the outflow boundary is not known a priori, which makes it difficult to impose the proper boundary condition at the outflow boundary. This difficulty has been avoided by using the open boundary condition (OBC) method. In this study, elastic viscous stress splitting (EVSS) formulation with streamline upwind (SU) method has been used in the finite element method. In order to test the validity of the OBC method, comparison between the results of fully developed condition at the outlet and those of OBC has been made for a Newtonian fluid. In the case of upper convected Maxwell (UCM) fluid, the effect of outflow boundary condition on the interface position has been investigated by using two meshes having different downstream lengths. In both cases, the results with the OBC method showed reasonable interface shape. In particular, for the UCM fluid the interface shape calculated with OBC was independent of the downstream length, while the results with the zero traction condition showed oscillation of interface position close to the outlet. Viscosity difference was found to be more important than elasticity difference in determining the final interface position. However, the overshoot of interface position near the con-fluent point increased with elasticity.

• 제어로봇시스템학회논문지
• /
• 제4권2호
• /
• pp.246-255
• /
• 1998

This paper presents a novel method for real-time malfunction detection of plasma etching process using EPD signal traces. First, many reference EPD signal traces are collected using monochromator and data acquisition system in normal etching processes. Critical points are defined by applying differentiation and zero-crossing method to the collected reference signal traces. Critical parameters such as intensity, slope, time, peak, overshoot, etc., determined by critical points, and frame attributes transformed signal-to symbol of reference signal traces are saved. Also, UCL(Upper Control Limit) and LCL(Lower Control Limit) are obtained by mean and standard deviation of critical parameters. Then, test EPD signal traces are collected in the actual processes, and frame attributes and critical parameters are obtained using the above mentioned method. Process malfunctions are detected in real-time by applying SPC(Statistical Process Control) method to critical parameters. the Real-time malfunction detection method presented in this paper was applied to actual processes and the results indicated that it was proved to be able to supplement disadvantages of existing quality control check inspecting or testing random-selected devices and detect process malfunctions correctly in real-time.