• Journal of Electrical Engineering and Technology
• /
• v.12 no.5
• /
• pp.1872-1882
• /
• 2017

Medium voltage drive systems driven by high-power multi-level inverters operating at low switching frequency can reduce the switching losses of the power device and increase the output power. Employing subsection synchronous current harmonic minimum pulse width modulation (CHMPWM) technique can maintain the total harmonic distortion of current at a very low level. It can also reduce the losses of the system, improve the system control performance and increase the efficiency of DC-link voltage accordingly. This paper proposes a subsection synchronous CHMPWM approach of active neutral point clamped five-level (ANPC-5L) inverter under low switching frequency operation. The subsection synchronous scheme is obtained by theoretical calculation based on the allowed maximum switching frequency. The genetic algorithm (GA) is adopted to get the high-precision initial values. So the expected switching angles can be achieved with the help of sequential quadratic programming (SQP) algorithm. The selection principle of multiple sets of the switching angles is also presented. Finally, the validity of the theoretical analysis and the superiority of the CHMPWM are verified through both the simulation results and experimental results.

• Wind and Structures
• /
• v.38 no.4
• /
• pp.277-293
• /
• 2024

The recorded thunderstorm winds at a point contain tri-directional components. The probabilistic characteristics of such recorded winds in terms of instantaneous mean wind speed and direction, and the probability distribution and the time-frequency dependent crossed and non-crossed power spectral density functions for the high-frequency fluctuating wind components are unclear. In the present study, we analyze the recorded tri-directional thunderstorm wind components by separating the recorded winds in terms of low-frequency time-varying mean wind speed and high-frequency fluctuating wind components in the alongwind direction and two orthogonal crosswind directions. We determine the time-varying mean wind speed and direction defined by azimuth and elevation angles, and analyze the spectra of high-frequency wind components in three orthogonal directions using continuous wavelet transforms. Additionally, we evaluate the coherence between each pair of fluctuating winds. Based on the analysis results, we develop empirical spectral models and lagged coherence models for the tri-directional fluctuating wind components, and we indicate that the fluctuating wind components can be treated as Gaussian. We show how they can be used to generate time histories of the tri-directional thunderstorm winds.

• Proceedings of the Korea Contents Association Conference
• /
• 2008.05a
• /
• pp.285-288
• /
• 2008

This study aims to rout optimized design flood discharge through prediction of the frequency-based precipitation from the frequency analysis with density of rainfall gage networks in urban watershed. Frequency analysis was examined for the measured rainfall depth with low density of a point and high density of the sub-basin divided into 13 points in watershed. The used rainfall data in order to analyze consists of two groups based on measured rainfall depth for a day duration with 39years of a point and 6years of 13 points by an extending as annual exceedance series, respectively. Selected rainfall data in this analysis show that low-network has maximum rainfall depth with duration 1hr-79.1mm and 24hrs-329.1mm, and high-networks have ones with duration of 1hr-93.0 mm and 24 hrs-245.0 mm, respectively. As the result, probability of the best in this study determined the Gumbel method from the goodness of fit test and the method of prime 6 probability distributions.

• The Research Journal of the Costume Culture
• /
• v.5 no.4
• /
• pp.130-158
• /
• 1997

This study outputs calculation of regression of each items for production of torso basic pattern according to 6 body types as the result of another study and intends to present drawing method of torso model by short measure method modified and supplied and supplied by experiments of wearing clothing. SAS(Statistical Analysis System) is used for figures management and methods for analysis used are Frequency Analysis, Means Analysis, Regression Analysis, Correlation Analysis, etc. Results are as follows. 1. Correlation analysis is used to output the size necessary for torso prototype drawing by sort measure method and waist front length, back length, crotch length, shoulder point-cerricale-shoulder point, bust circumference, waist circumference, weight, etc, are set up as representative items calculation of regression of each type is suggested. 2. In the result of experiment of the first wearing clothing intended for 5 in each type and the whole 30, to develop torso prototype drawing method by short measure method, as we find some problems of the shape and propriety of neck root circumference line, the position of shoulder point, pulling or hold armpit parts, waist circumference line, the degree of dissatisfaction is high, so the second experiment of wearing clothing is propriety of each part is improved, all items except the length and quantity of shoulder dart, waist in back bodice, clearance quantity of hip circumference, and the place of shoulder line in side bodice. So, it was modifed and supplied and then the third torso prototyped drawing method by shout measure method was suggested. The third prototype drawing method was suggested, by modifying and supplying.

• Journal of Mechanical Science and Technology
• /
• v.15 no.2
• /
• pp.232-238
• /
• 2001

Fast Fourier Transformation is employed to convert the head variation of a pipeline in the time domain to the amplitude of the frequency domain. Applying method of characteristics to a pipeline provides a significant frequency range for a surge introduced from the valve modulation. Inverse Fast Fourier Transformation and a Finite Impulse Response Filter can be used to remove any possible noise existing from the significant frequency range of an unsteady condition. A filtered signal shows higher potential for the inverse calculation of leakage detection than the noise-added signal does. The respective performances of Inverse Fast Fourier Transformation and a Finite Impulse Response Filter are compared in terms of leakage detection capability. Characteristics of the frequency range for multiple leakages were investigated to validate the effectiveness of the noise control method in the frequency domain.

• Proceedings of the KIEE Conference
• /
• 2006.07a
• /
• pp.8-9
• /
• 2006

This paper presents a new methodology to calculate an optimal solution of equilibrium to power system differential algebraic equations. It employs a nonlinear interior point method for solving the optimization formulation, which includes dynamic equations representing two-axis synchronous generator models with AVR and speed governing control, algebraic equations, and steady-state nonlinear loads. Equilibrium optimization (EOPT) is useful for diverse purposes in power system analysis and control with consideration of the system frequency constraint.

• Journal of the Korean Home Economics Association
• /
• v.37 no.8
• /
• pp.55-72
• /
• 1999

The purpose of this study is to identify the levels of informationized life of individual, consumers knowledge and attitudes to informationized society, and the recognition of consumer problems in informationized society, and to investigate the related variables. Data were collected from 693.consumers living in Seoul using the constructed questionnaires by the authors. Frequency, Percentage and Multiple Regression Analysis were applied for the analysis. The level of informationized life of consumers was lower than the mid-point of the scale, the level of the consumers knowledge about informationized society was sightly higher than mid-point of the scale, and the consumer attitudes to informationized society appeared to be positive. The level of the recognition of consumer problems in informationized society was higher than the mid-point of the scale,and was influenced by job, age of consumers, and the level of consumers knowledge about informationized society.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.11
• /
• pp.1950-1956
• /
• 1997

An engineering goal in vibration and noise professionals is to develope quiet machines at the preliminary design stage, and various numerical techniques such as FEM, SEA or BEM are one of the schemes toward the goal. In this paper, the research has been focused on the sensitivity effect of mesh sizes for FEM application so that the optimum size of the mesh that leads to engineering solution within acceptable computing time could be generated. In order to evaluate the mesh size effect, three important parameters have been examined : natural frequencies, number of modes and driving point mobility. First, several lower modes including the fundamental frequency of a 2-D plate structure have been calculated as mesh size changes. Since theoretical values of natural frequencies for a simple structure are known, the deviation between the numerical and theoretical values is obtained as a function of mesh size. The result shows that the error is no longer decreased if the mesh size becomes a quarter wavelength or smaller than that. Second, the mesh size effect is also investigated for the number of modes. For the frequency band up to 1.4 kHz, the structure should have 38 modes in total. As the mesh size reaches to the quarter wavelength, the total count in modes approaches to the same values. Third, a mobility function at the driving point is compared between SEA and FEM result. In SEA application, the mobility function is determined by the modal density and the mass of the structure. It is independent of excitation frequencies. When the mobility function is calculated from a wavelength to one-tenth of it, the mobility becomes constant if the mesh becomes a quarter wavelength or smaller. We can conclude that dynamic parameters, such as eigenvalues, mode count, and mobility function, can be correctly estimated, while saving the computing burden, if a quarter wavelength (.lambda./4) mesh is used. Therefore, (.lambda./4) mesh is recommended in structural vibration analysis.

• Journal of Mechanical Science and Technology
• /
• v.17 no.8
• /
• pp.1148-1155
• /
• 2003

The finite element method is one of the methods widely applied for predicting vibration in mechanical structures. In this paper, the effect of the mesh size of the finite element model on the accuracy of the numerical solutions of the structural vibration problems is investigated with particular focus on obtaining the optimal mesh size with respect to the solution accuracy and computational cost. The vibration response parameters of the natural frequency, modal density, and driving point mobility are discussed. For accurate driving point mobility calculation, the decay method is employed to experimentally determine the internal damping. A uniform plate simply supported at four corners is examined in detail, in which the response parameters are calculated by constructing finite element models with different mesh sizes. The accuracy of the finite element solutions of these parameters is evaluated by comparing with the analytical results as well as estimations based on the statistical energy analysis, or if not available, by testing the numerical convergence. As the mesh size becomes smaller than one quarter of the wavelength of the highest frequency of interest, the solution accuracy improvement is found to be negligible, while the computational cost rapidly increases. For mechanical structures, the finite element analysis with the mesh size of the order of quarter wavelength, combined with the use of the decay method for obtaining internal damping, is found to provide satisfactory predictions for vibration responses.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.1
• /
• pp.23-29
• /
• 2003

This paper proposes an efficient feature extraction of the images by using independent component analysis(ICA) based on neural networks of the hybrid learning algorithm. The proposed learning algorithm is the fixed point(FP) algorithm based on Newton method and moment. The Newton method, which uses to the tangent line for estimating the root of function, is applied for fast updating the inverse mixing matrix. The moment is also applied for getting the better speed-up by restraining an oscillation due to compute the tangent line. The proposed algorithm has been applied to the 10,000 image patches of $12{\times}12$-pixel that are extracted from 13 natural images. The 144 features of $12{\times}12$-pixel and the 160 features of $16{\times}16$-pixel have been extracted from all patches, respectively. The simulation results show that the extracted features have a localized characteristics being included in the images in space, as well as in frequency and orientation. And the proposed algorithm has better performances of the learning speed than those using the conventional FP algorithm based on Newton method.