• Structural Engineering and Mechanics
• /
• 제22권6호
• /
• pp.741-759
• /
• 2006

A general theory which describes the elastic response of a curved anisotropic plate subjected to stretching and bending will be developed by considering the nonlinear effect that reflecting the non-flat geometry of the structure. By applying a newly derived $6{\times}6$ matrix constitutive relation between force resultants, moment resultants, mid-plane strains and deformed curvatures, the governing differential equations for a curved anisotropic plate is developed in the usual manner, namely, by consideration of the constitutive relation and equilibrium equations. Solutions are obtained for simply-supported boundary conditions and compared to corresponding solutions that neglecting the nonlinear effect in the analysis. The comparisons indicate that the nonlinear terms in the equations that caused by the curvature of the structure is crucial for the curved plate analysis. Under certain curved plate geometries the unreasonable results will be induced by neglecting the nonlinear effect in the analysis.

• Structural Engineering and Mechanics
• /
• 제54권2호
• /
• pp.239-256
• /
• 2015

An adaptive-scale damage detection strategy based on a wavelet finite element model (WFEM) for thin plate structures is established in this study. Equations of motion and corresponding lifting schemes for thin plate structures are derived with the tensor products of cubic Hermite multi-wavelets as the elemental interpolation functions. Sub-element damages are localized by using of the change ratio of modal strain energy. Subsequently, such damages are adaptively quantified by a damage quantification equation deduced from differential equations of plate structure motion. WFEM scales vary spatially and change dynamically according to actual needs. Numerical examples clearly demonstrate that the proposed strategy can progressively locate and quantify plate damages. The strategy can operate efficiently in terms of the degrees-of-freedom in WFEM and sensors in the vibration test.

• Steel and Composite Structures
• /
• 제35권1호
• /
• pp.1-12
• /
• 2020

This article deals with the buckling analysis in the plates containing carbon nanotubes (CNTs) subject to axial load. In order to control the plate smartly, a piezoelectric layer covered the plate. The plate is located in elastic medium which is modeled by spring elements. The Mori-Tanaka low is utilized for calculating the equivalent mechanical characteristics of the plate. The structure is modeled by a thick plate and the governing equations are deduced using Hamilton's principle under the assumption of higher-order shear deformation theory (HSDT). The Navier method is applied to obtain the bulking load. The effects of the applied voltage to the smart layer, agglomeration and volume percent of CNT nanoparticles, geometrical parameters and elastic medium of the structure are assessed on the buckling response. It has been demonstrated that by applying a negative voltage, the buckling load is increased significantly.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.408-413
• /
• 2004

High speed planning boats also have been required more and more the rational strength analysis and evaluation for the optimal structural design in respect of the structural lightness according to the high speed trend. Even though the suggestion of the simple type equation for the equivalent dynamic pressure is reasonable to design the scantling of ship structure conveniently, many research activities for more reasonable improvement of the simple design pressure, have been continued to suggest the more accurate equivalent static description of tire structural response such as the deflection and stress of hull structure. In this research, we focus on the aluminum bottom stiffened plate structure in which structural scantling is mainly depend on the local loads such as dynamic or impact pressure without other load effects and structural response for the simple dynamic equivalent pressure was investigated through the structural analysis. In order to investigate the structural response of the bottom stiffened plate structure subjected to the dynamic equivalent design pressure, linear and nonlinear structural analysis of the bottom stiffened plate structure of 4.3 ton aluminum planning boat was performed based on the equivalent static applied loads which were derived from the KR regulation and representative one among various dynamic equivalent pressure equations. From above analysis results, we found that the response such as deflection and stress of plate member was similar with the response results of one plate member model with fixed boundary, which was published previous paper and in case of KR design loading, all response of stiffened plate structure were within elastic limit. Through the nonlinear analysis, nearly elastic behavior including the slight geometrical nonlinear response was dominant but plastic local zone was appeared at $85\%$ limit load. Therefore, we can say that through tire linear and nonlinear analysis, this stiffened plate member has no structural strength problem based on the yield criteria in case within $60\%$ limit load except the other strength point of view such as the fatigue and buckling problem.

• 전기학회논문지P
• /
• 제58권1호
• /
• pp.67-71
• /
• 2009

This research is a new structure of the semiconductor substrate heating apparatus in which the assembly and expansion are possible. The fast thermo-responsive according to the direct heating structure of the heating plate layer adhering closely to the floor side of a substrate and the fast heat loss minimization can be accomplished. Moreover, the contact area of the sheath heater, which is the heating plate layer built-in heating apparatus, is increased, so that it has more heating valid area. There is no problem with the deformation interpreted in the state where it assembles the block of a several of the simulation result structure, the safety, and the stress. In addition, it is confirmed that building a large-size heating block is possible since the temperature deflection of the manufactured plate is lower than the standard value.

• Journal of Welding and Joining
• /
• 제8권3호
• /
• pp.79-88
• /
• 1990

Welded joint often contains soft or softened regions such as the HAZ of TMCP steel welded with high heat input. In this study, the equivalent yield strength of plate structure containing softened region was predicted by FEM analysis, and its incremental behavior was explained with the results of the analysis. The calculated results of yield strength indicated the following for the plate structures. 1) As the softened region starts to yield, shear stress begins to build up along the boundary between base metal and softened region. This results in multi-axial stress condition which gives restraint on the softened region. 2) Restraint effect has a significant influence on the distribution of the shear stress, the nominal stress, and the strain. 3) The yielding behavior of softened region becomes the same as that of base metal when both ratios of length to width and thickness to width of softened region are larger than 30 and 13 respectively.

• 한국산학기술학회논문지
• /
• 제19권5호
• /
• pp.661-671
• /
• 2018

강판 콘크리트구조에 대한 국내 연구는 대체적으로 강도가 큰 원전 구조물에 초점을 맞추고 있다. 현재 안전성과 시공성 측면에서 유리한 SC구조는 특수구조물에만 한정되어 적용되어 왔으며, 최근 구조적으로 장점이 명확한 SC구조에 대해 일반건축물에 적용하기 위한 연구가 진행되고 있다. 본 연구에서는 SC 구조를 일반 건축물에 적용하기 위한 기초 연구로서 특히 SC 구조에서 중요한 요소인 콘크리트의 시멘트를 고로슬래그로 대체하여 친환경성에 부합한 구조체를 계획하기 위해 무시멘트 콘크리트를 적용한 SC 구조의 기본 설계 정보를 제시하고자 한다. 이 논문에서는 압축 특성, 중심 압축 하중을 받는 유효좌굴길이계수에 대해 연구하였다. 유효좌굴길이계수를 산정하기 위해서 판 이론을 적용하지 않고 오일러 기둥 이론으로 계산하였다. 유효좌굴길이계수를 계산할 때 필요한 변형률을 측정하여 강판의 항복강도, 강판의 좌굴 및 콘크리트가 파단되는 시점에서의 유효좌굴길이계수를 계산하였다. 또한, 세장비(B/t)를 변수로 최대 압축강도가 국외 및 국내 기준식에 부합하는 지를 검토하였으며 기둥 이론을 적용하여 실험체의 좌굴을 분석하고 측정된 강판의 변형률을 선택하는 방법에 따라 유효좌굴길이계수를 분석하여 기준식에서 제시하는 값과 비교하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 추계학술대회 논문집
• /
• pp.273-274
• /
• 2006

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표대회 논문집(III)
• /
• pp.861-866
• /
• 1998

This study is numerical procedure of strengthening capacity in a field structure and compare analysis data with test data. Recently, many strengthening methods are developed and used to rehabilitate existing structure. However, both theoretical background and applying techniques are not established yet. One of the most popular method is plate bonding method using either steel plate or carbon plate. This theoretical background and applying techniques are very important and those applications are differed when applied in field strengthening cases. Also depending on the analysis out come, displacement increased based n the condition of members while reaching ultimate load or failure load.

• Journal of the Optical Society of Korea
• /
• 제11권3호
• /
• pp.118-123
• /
• 2007

The emitting structure of multi-channel-type flat fluorescent lamps (FFLs) combined by a lenticular-lens-patterned diffuser plate was optimized by the ray tracing technique. The optimal parameters such as the distance between the channels of the FFL and the distance between the FFL and the diffuser plate were suggested from the viewpoint of the luminance uniformity. The best luminance uniformity, which was higher than 90%, was obtained at the channel distance of 4 mm and the distance of 12.5 mm between the FFL and the patterned diffuser plate.