• 한국기계가공학회지
• /
• 제20권3호
• /
• pp.60-67
• /
• 2021

Recently, research attention has been focused on vibration-free vehicles to transport small numbers of expensive electronic products. Vibration-free vehicles can be used to transport expensive test equipment or semiconductors, mainly produced in the domestic IT industry, and can serve as a readily available transportation system for short driving distances due to the increased efficiency on narrow national highways. This study was aimed at developing a Z-Spring to minimize the vibration by installing an air spring instead of the plate spring applied to conventional freight cars and to prevent the damage of the loaded cargo from the shock occurring during movement. The mechanical properties (elastic modulus, tensile strength, and shear strength) of carbon fiber (CF) and glass fiber (GF) prepreg were derived, and ANSYS ACP PrepPost analyses were performed. It was observed that in the case of hybrid composites, the total deformation and equivalent stress are higher than that of CFRP; however, in terms of the unit cost, the hybrid Z-Spring is more inexpensive and durable compared to the GF.

• 한국미생물·생명공학회지
• /
• 제43권3호
• /
• pp.259-266
• /
• 2015

온난화, 고령화, 세계화로 인하여 변화하는 국내 보건환경에 현행 수질기준이 적합할 지 평가가 필요하다. 본 연구는 총대장균군 만으로 규정된 현행 온천수 수질기준의 타당성을 환경유래 내열성세균인 레지오넬라균 오염도를 검출로 평가하였다. 온천수에서 레지오넬라균을 검출한 7개의 논문에 보고된 미생물 자료에 대한 메타분석을 실시하였다. 레지오넬라균의 검출 유무의 오즈비는 총대장균군과 유의한 상관도를 보였다[odds ratio (OR), 3.1 (1.5−6.4, 95% CI), p = 0.002]. 그러나, 레지오넬라균 오염을 분변성 중온균인 총대장균군 지표가 감지할 수 있다는 점은 단순히 설명되지 않기에, 그 기작을 검토하였다. 레지오넬라균의 검출 유무는 일반세균수와 더 높은 오즈비를 보였고[4.0(2.2−7.2), p < 0.001], 40°C 미만의 수온범위에서 수온과 강한 상관도[OR, 4.3(1.4−13.6), p = 0.011], 50°C 이상에서는 수온과 음의 상관도를 보였다[OR, 0.2 (0.1−0.4), p < 0.001]. 따라서, 수온에 의하여 세균의 현존량이 결정되는 현상 때문에 총대장균군수와 레지오넬라균 유무가 연관성을 가진 것으로 판단된다. 이에 따르면, 총대장균군보다 일반세균수가 더 직접적으로 비분변성 병원체의 증감을 반응할 것으로 생각되므로, 일반세균수를 단일 수질관리 기준으로 사용하거나, 현행 기준에 일반세균수를 추가하는 것이 타당한 것으로 판단된다.

• 소성∙가공
• /
• 제27권4호
• /
• pp.236-243
• /
• 2018

A multi-point forming die (MPFD), which has been used for producing curved plates, is capable of forming various curved plates with just one MPFD. However, in real industries, an MPFD is difficult to be adopted since the structural properties, punch strength, elastic recovery correction and dimensional accuracy become problems. In order to overcome these problems, the hot multi-point forming die (HMPFD) was proposed in this study. This HMPFD commonly provide more less spring-back and forming load than conventional MPFD. Nevertheless, this process is very difficult to form the curved plate, because the final curved shape of the plate depends on many process variables such as the punch/nozzle arrangement (height and distance), the radius of punch, contact conditions between plate and punch. In this study, the forming characteristics of HMPFD and conventional MPFD are compared with each other through the finite element analysis.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권2호
• /
• pp.140-148
• /
• 2000

In this paper, using surface micromachining technology with thick photoresist and aluminum, an SLM(Spatial Light Modulator), which is applied to the fields of adaptive optics and pattern recognition system, was fabricated and the electromechanical properties of the fabricated micro SLM are measured. In order to maximize fill-factor and remove mechanical coupling between micro SLM actuators, the micro SLM is composed of three aluminum layers so that spring structure and upper electrode are placed beneath the mirror plate, and $10\times10$ each mirror plate is individually actuated. Also, the micro SLM was designed to be able to modulate phase and amplitude of incoming light in order to have a continuity of phase modulation of incoming light. In the case of amplitude and phase modulation, maximum vertical displacement is 4$\mum$, and maximum angular displacement is $\pm4.6^{\corc}$ respectively. The height difference of the fabricated mirror plate was able to be reduced to 1100A with mirror plate planarization method using negative photoresist(AZ5214). The electromechanical properties of the fabricated micro SLM were measured with the optical measurement system using He-Ne laser and PSD(position sensitive device).

• 자원환경지질
• /
• 제7권1호
• /
• pp.1-21
• /
• 1974

From the point of view of geological history, the land of South Korea is regarded as the subject of processes of the changes in formations of several geological blocks such as Kyonggi massif, Yeongnam massif, Taebaegsan basin, Kyungsang basin and so on. Through the long period of geological chronology, the present topography and geotectonics have been formed by the complicate interactions of epirogenetic movements, magmatism, orogenesis, differential vertical movements, metamorphism and sedimentation. The reason of the crust movements mentioned above, is suppossed that the Pacific and West Pacific plate have subducted directly or indirectly into the East Asia plate. This fact can be endorsed by the results of the studies on the heat flow, gravity anomaly, absolute age dating, tectonic lineation, lithofacies and the temperature of hot spring in South Korea. The formations of metal ore deposits as well as other geological processes can be determined by the mechanical control of the plates and be divided into several systematic patterns. The investigation of about 110 metal mines in South Korea shows the following results. (1) Plate boundary volcanic type is about 28% (2) Plate boundary plutonic type is about 44% (3) Intraplate sedimentary type is about 26% (4) Intraplate magmatic type is about 2%.

• Advances in nano research
• /
• 제13권4호
• /
• pp.369-378
• /
• 2022

Dynamic study of concrete plates under impact load is presented in this article. The main objective of this work is presenting a mathematical model for the concrete plates under the impact load. The concrete plate is reinforced by carbon nanoparticles which the effective material proprieties are obtained by mixture's rule. Impacts are assumed to occur normally over the top layer of the plate and the interaction between the impactor and the structure is simulated using a new equivalent three-degree-of-freedom (TDOF) spring-mass-damper (SMD) model. The structure is assumed viscoelastic based on Kelvin-Voigt model. Based on the classical plate theory (CPT), energy method and Hamilton's principle, the motion equations are derived. Applying DQM, the dynamic deflection and contact force of the structure are calculated numerically so that the effects of mass, velocity and height of the impactor, volume percent of nanoparticles, structural damping and geometrical parameters of structure are shown on the dynamic deflection and contact force. Results show that considering structural damping leads to lower dynamic deflection and contact force. In addition, increasing the volume percent of nanoparticles yields to decreases in the deflection.

• 한국환경보건학회지
• /
• 제24권1호
• /
• pp.141-150
• /
• 1998

This study was performed to investigate the distribution of Yersiniae and correlation between Yersiniae and indicator organism by time and area in spring water located in northern part of Seoul. Samples collected from 46 spring waters located in four mountains(Dobong, Bukhan, Surak, Bulam) were inspected to detect Yersiniae and indicator organisms. And also there were examined bioserological characteristics and resistance of ahtibiotics of the isolated Yersiniae.The result were as follows. 1. The isolation rate of Yersiniae was 22% in February and 20% in April. The isolated species were 6 strains of Y. enterocolitica, 6 strains of Y. aldova, 4 strains of Y. intermedia and 43 strains of Y. pseudotuberculosis. The serotype of Y. pseudotuberculosis isolated from was all O:5 and biotype of Y. enterocolitica isolated from was all O:3. 2. The Geometric mean of standard plate count, coliform, and psychrotrophilic bacteria were 3.4 CFU/ml, 1.2 MPN/100 ml and 33.0 CFU/ml in February and 3.1 CFU/ml, 1.5 MPN/100 ml and 20.5 CFU/ml in April respectively. There was no significant difference by time and area but the indicator organisms were correlated significantly with each other (p<0.05). 3. Because detection of Yersiniae was not statistically associated with indicator organism, Yersiniae can be detected in the spring water approved microbiologically (p<0.05). 4. The Yersiniae isolated were resistant to Ampicillin, Colistin, Carbenicillin and Coilstin. All isolaed Y. enterocolitica were resistant to Ampicillin (100%). In the case of Y. pseudotuberculosis, only 1 of 3 isolated was resistant to Colistin but susceptible to other antibiotics.

• 한국전산구조공학회논문집
• /
• 제31권5호
• /
• pp.243-250
• /
• 2018

본 논문에서는 복합재 판 스프링의 설계 최적화를 위해 유전자 알고리즘을 사용한 적층 최적화 과정을 제시하였다. 다목적 소형 승합 자동차 판 스프링을 유한요소모델로 구성하여 초기 설계를 검증한 이후, 유전자 알고리즘을 통해 복합재료의 적층수와 적층각도를 최적화하는 과정을 기술하였다. 최적화 과정을 통해 판 스프링의 하중 감소과정, 반복수에 따라 강 구조의 해석 결과와 비교하였다. 더불어 유전자 알고리즘을 통해 최적화된 적층 시퀀스를 구조에 적용하여 구조의 건전성을 검증하기 위해 유한요소 모델로 구성하여 안전여유를 계산하였다. GA를 적용할 때, 복합재료 판 스프링의 적층 두께와 적층 각을 획득하였으며, 이는 적절한 강도와 강성으로 최소 무게를 달성하는데 기여한다. 동일한 설계 매개 변수 및 최적화 조건에서 강철된 판 스프링을 복합재 판 스프링으로 교체하면 65.6%의 중량이 감소한다.

• 한국정밀공학회지
• /
• 제23권1호
• /
• pp.129-135
• /
• 2006

In this study, a two-axis ultra-precision stage driven by piezoelectric elements is presented. The stage has a flexure-type parallel linear guide mechanism consisting of quad-symmetric simple parallel linear springs and quad-symmetric double compound linear springs. While the simple parallel linear springs guide the linear motion of a moving plate in the stage, the double compound linear springs follow the motion of the simple parallel linear spring as well as compensate the parasitic motions caused by the simple parallel linear springs. The linear springs are designed by rectangular beam type flexures that are deformed by bending deflection rather than axial extension, because the axial extension is smaller than the bending deflection at the same force. The designed guide mechanism is analyzed by finite element method(FEM). Then two-axis parallel linear stage is implemented by the linear guide mechanism combined with piezoelectric elements and capacitance type displacement sensors. It is shown that the manufactured ultra-precision stage achieves 3 nm of resolution in x- and y-axis within 30 ${\mu}m$ of operating range.

• 대한기계학회논문집A
• /
• 제23권11호
• /
• pp.2022-2032
• /
• 1999

In recent years, the subject of remaining life assessment has drawn considerable attention in the power generation industry. In power generation systems a variety of structural components, such as steam pipes, turbine rotors, and superheater headers, typically operate at high temperatures and high pressures. Thus a life prediction methodology accounting for fracture and rupture is increasingly needed for these components. For accurate failure assessment, in addition to the single parameter such as K or J-integral used in traditional fracture mechanics, the second parameter like T-stress describing the constraint is needed. The most critical defects in such structures are generally found in the form of semi-elliptical surface cracks in the welded piping-joints. In this work, selecting the structures of surface-cracked plate and straight pipe, we first perform line-spring finite element modeling, and accompanying elastic-plastic finite element analyses. We then present a framework for including constraint effects (T-stress effects) in the R6 failure assessment diagram approach for fracture assessment.