• The Korean Journal of Petroleum Geology
• /
• v.13 no.1
• /
• pp.17-23
• /
• 2007

Gravity characteristics are investigated in the vicinity of the DASAN scientific station, located at the Svalbard Archipelago, the Arctic using ArcGP data. Boundary effects of free-air gravity anomalies, which appeared generally at the continental margin, are erased after Bouguer correction was applied. Complete Bouguer anomalies produced after terrain correction by GrOPO30 show that gravity anomalies increase from continent to marine. This phenomena seem to be related to the rise of Moho discontinuity. The cut-off frequency of 0.16 was decided after power spectrum analysis and the gravity anomalies were divided into two parts. Residual anomalies in high frequency part show that characteristics of high values along the faults and of low values related to thick sediments in the continent. Characteristic is low values from basement subsidence of continental slope or thick sediments in the marine. The undulation of Moho discontinuity from 3-D inversion modeling show typical characteristics of continental margin that become higher from Svalbard archipelago to Knipovich ridge bordering Eurasian plate.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.3 s.46
• /
• pp.239-250
• /
• 2000

This study investigates the mechanical behavior on trough rib to crossbeam joint in orthotropic steel plate decks, specially emphasizing on the effect of diaphragm inside trough rib on the fatigue behavior of slit by static and fatigue tests. In particular, the effects of diaphragm on in-plane stress and out-of-plane stress, stress concentration, propagation of fatigue cracks at the silt are studied. With the result of experiment and numerical analysis, we have estimated the fatigue strength using the nominal stress and hot-sport stress. The details with diaphragm have occurred about 50% stress reduction at trough rib part of trough rib to crossbeam joint than the detail without diaphragm, however, the lower parts of crossbeam have occurred much more stress. Initial crack size or slit have an considerable influence on the propagation of fatigue cracks due to V-notch. The fatigue strength category of the details without diaphragm has higher value than fatigue limit, whereas that of the details with diaphragm is estimated lower than fatigue limit.

• Tribology and Lubricants
• /
• v.35 no.6
• /
• pp.369-375
• /
• 2019

This paper presents a new method on how to calculate the thrust forces acting on an auto-leveling device in headlamps for passenger vehicles. The leveling device is used to lower the angle of lights when a load in the trunk of the vehicle lifts it. In the process of the headlamp design, it is imperative to predict the external forces so that the designers can decide whether to proceed or not. The device is composed of three pivot joints with no reaction moment, a plate that holds the lamp, and a leveling motor that changes rotation to linear motion. In this study, force balance, moment balance, and geometric compatibility are applied to the leveling device system so that a nonlinear system of equations can be derived; the multi-dimensional Newton-Raphson algorithm is then used to solve these. A sensitivity analysis is carried out to verify which design variables affect the system the most: the mass of the lamp and the height between the pivot and leveling device affect the thrust forces the most. Then, considering the friction forces between the moving parts, the hysteresis of the forces are derived. An experimental apparatus, designed and developed in this study, is used to verify the exactness of the derived equations. The results from experiments coincide well with the calculated results. The friction hysteresis, in particular, proves this upon analysis.

• Applied Biological Chemistry
• /
• v.40 no.4
• /
• pp.318-322
• /
• 1997

As an investigation for utilization of squid viscera oil as a food source, we attempted to improve a quality of fish burger by addition of emulsion curd formed from gelatin, water and refined squid viscera oil. Judging from the results of peroxide value, brown pigment formation, color value of Hunter, jelly strength and sensory evaluation, the reasonable amount of emulsion curd for the improvement of a fish burger functionality was determined as 6% on the weight basis of the chopped mackerel meat. Total plate counts, volatile basic nitrogen and histamine contents in fish burger prepared by addition of 6% of emulsion curd were $6.2{\times}10^4\;CFU/g$, 19.0 mg/100 g, and 50.7 mg/100 g, respectively. It may be concluded, from the above results that the emulsion curd-added fish burger is a safe as a food commodity. The ratio of polyenes to saturates of emulsion curd-added mackerel burger was 1.13. By adding emulsion curd formed from gelatin, water and refined squid viscera oil, color in cross section, texture and lipid functionality of mackerel burger could be improved in part.

• Journal of Korean Society for Atmospheric Environment
• /
• v.24 no.4
• /
• pp.415-422
• /
• 2008

This study was carried out to investigate the effect of operating and design conditions of gas dispersion type of absorber on $SO_2$ removal efficiency. pH difference between upper and lower part of gas dispersing plate of absorber was 0.2, which was relatively low. This was supposed that recirculation capacity of absorbing liquid between froth zone and reaction zone of absorber be increased by oxidation air injection through liquid riser which acted as liquid pump. Test results showed that $SO_2$ removal efficiency was more sensitive than absorber ${\Delta}P$. High $SO_2$ removal even at lower pH resulted from very low concentration of $HSO_3^-$ ion in absorbing liquid because of direct supply of dissolved oxygen into froth zone. 96% of $SO_2$ removal efficiency was obtained under the condition of absorber pH 5.2, flue gas flow rate of $1,530\;Nm^3/hr$, inlet $SO_2$ concentration of 800 ppm, absorber ${\Delta}P$ of 250mmAq. The following equation by a multiple linear regression was obtained to describe the relationship between $SO_2$ removal and operating variables. $$f=1-{\exp}(-1.3939+1.060pH+0.0139{\Delta}P-0.00267G-0.000064SO_2Conc.),\;R^2=0.9719$$

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.9 no.2
• /
• pp.79-84
• /
• 2006

The present study deals with the flow over a flat plate with repeated roughness elements of 2-dimensional rectangular shape, which can be applied into the study on the natural geographical roughness and the turbulent flow on roughened solid surface. Experiment was performed using PIV technique in the circulating water channel. Results showed that the flow over roughness elements was characterized by the high shear flow emanating from top of roughness element and the recirculating region formed at the trough of two roughness elements. In general, the ratio between the spacing and the height of roughness elements plays a crucial role in developing the flow pattern near wall surface.

• Korean Chemical Engineering Research
• /
• v.47 no.6
• /
• pp.688-694
• /
• 2009

A spray-type cleaning agent in utilizing dust-remover on PCB was chosen to study the cleanliness test and efficiency. In order to choose alternative environmental-friendly cleaning agents, it is important that the systematic selection procedures should be introduced and applied through the evaluation of their cleaning ability, environmental characteristics, and economical factors, and that the objective and effective evaluation methods of cleanliness should be established for the industry. A novel cleaning evaluation method with scanning electron microscopy/energy-dispersive X-ray analysis of surface observation evaluation method and an infra-red thermography camera(THERMOVISION A20 model) was studied in this work. The sound card(CT-2770 model) cut by $2{\times}2cm$ size was used as a part, and before and after the spray cleaning, the cleanliness was observed by the image analyzer of SEM and further the removal efficiency of dust was quantitatively evaluated by the component analysis of EDX. For the parts of P4TE model motherboard and IPC-A-36 PCB plate, before and after the spray cleaning, temperature differences were measured and compared at room temperature and 50 oven temperature by an infra-red thermography camera in the contaminants of dust and iron powder.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.5
• /
• pp.41-51
• /
• 2012

Heliostat field is the most important subsystem in the tower type solar thermal power plant since its optical performance affects the total system efficiency most significantly while the construction cost of it is the major part of total construction cost in such a power plant. Thus a well designed heliostat field to maximize the optical efficiency as well as to minimize the land usage is very important. This work presents methodology, procedures and result of heliostat filed design for 200kW solar thermal power plant built recently in Daegu, Korea. A $2{\times}2(m)$ rectangular shaped receiver located at 43(m) high and tilted $28^{\circ}$ toward heliostat field, 450 of heliostats of which the reflective surface is formed by 4 of $1{\times}1(m)$ flat plate mirror facet, and the land area having about $140{\times}120(m)$ size are used to form the heliostat field. A procedure to deploy 450 heliostats in radial staggered nonblocking formation is developed. Also the procedures to compute the cosine effect, intercept ratio, blocking and shading ratio in the field are developed. Finally the heliostat filed is designed by finding the optimal radial distance and azimuthal spacing in radial staggered nonblocking formation such that the designed heliostat field optical efficiency could be maximized. The designed heliostat field has 77% of annual average optical efficiency, which is obtained by annually averaging the optical efficiencies computed between the time of where sun elevation angle becomes $10^{\circ}$ after sunrise and the time of where sun elevation angle becomes $10^{\circ}$ before sunset in each day.

• Journal of Digital Convergence
• /
• v.15 no.6
• /
• pp.339-344
• /
• 2017

In this study, microorganisms were isolated from nosocomial environment and are identified by biochemical analysis as the part of biochemical and technical convergence. Microorganisms were collected at intense care unit of general hospital located in Pyeongtak (2014.11.28. - 2014. 11. 30). Using a VITEK2 equipment of biochemical approaches, eleven microorganisms e.g., Micrococcus luteus (or M. lylae), Granulicatella adiacens (M. luteus or M. lylae), Staphylococcus caprae, Sphingomonas paucimobilis, Kocuria kristinae, G elegans, Aerococcus viridans (or Staphylococcus arlettae), Methylobacterium spp., Dermacoccus nishinomiyaensis (or Kytococcus sedentarius), Kocuria kristinae (or M. luteus, M. lylae), Pseudomonas oryzihabitans were identified. And then identified bacteria plates were applied with a plastic stick, so called with "FarmeTok (medistick/Puristic) to produce ClO2. ClO2-releasing plastic stick showed the very strong inhibition of bacterial growth with about 99.9%. There were no bacterial colonies on the ClO2-incubated plate. Taken together, it is suggested that chlorine dioxide should be very strong inhibitor to microorganisms of nosocomial infections.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.4
• /
• pp.321-327
• /
• 2007

In an apartment house that is generally air-tight and well insulated, the combustion gas from cooking devices is the major source of air pollution in the kitchen. It spreads throughout the house affecting the overall Indoor all quality. In this study, the performance of the kitchen range hood which employs air induction and air curtain was investigated by numerical simulation. The results are compared with that of two other kitchen range hoods which are in general use. The two general types of range hoods considered in the present calculations are box and plate type range hoods. The former has a large capture space between the filter and suction duct, while the latter has little. It was found that the capture efficiency of the kitchen range hood with air induction and air curtain Is higher than that of the general types of range hoods by 20% approximately The reason may be because the air induction and the air curtain block the air stream escaping from the front and the side part of range hoods effectively and because an additional fan for air induction and air curtain increases suction flow rates.