• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.5
• /
• pp.209-217
• /
• 2011

In recent days, while taller and more massive structures such as huge bridges and super skyscrapers have been welcomed, the structural stabilization in design and construction have been gradually limited due to the major weakness of current concrete which is relatively heavier when compared with its strength. To improve the weakness of the current concrete, The lightweight concrete with light weight and high strength should be used; however, not many researchers in Korea have studied on the lightweight concrete. Generally, artificial lightweight aggregate produced through high-temperature-plasticization has a possibility of its body-expansion with many bubbles. Therefore, depending on the size of aggregate, the effects of bubbles on the specific weight and strength of the lightweight concrete should be studied. In this study, considering grain-size, the mix design of the artificial lightweight aggregate produced through the high-temperature-plasticization and the body-expansion of waste and clay from the fire power plant in Korea was conducted. The experiment to analyze the variation in specific weight and strength of the lightweight concrete was followed. From these experiments, the optimized grain-size ratio of the artificial lightweight aggregate for the enhancement of high-strength from the lightweight concrete was revealed.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.18 no.1
• /
• pp.113-120
• /
• 1994

The Purpose of this study was to improve the moisture related properties of viscose rayon fibers. Viscose rayon filament yarns were partially etherified to make CMC fibers. CMC fibers were converted to the sodium, calcium, and ferric salt forms by an ion exchange method. The property changes of ion exchanged CMC fibers were examined. Cation contents of fibers were varied depending on the degree of substitution of CMC fibers. The strength of Na, Ca, Fe-CMC was higher than H-CMC owing to the plasticization by moisture sorption and the crosslinking by cations. The moisture regain was increased by carboxymethylation and that of Fe-CMC showed the highest value. The degree of swelling determined by the water retention value was observed to be Na-CMC > Ca-CMC > H-CMC > Fe-CMC. The solution retention value was decreased in the order . Ca-CMC > Na-CMC > H-CMC > Fe-CMC.

• Textile Coloration and Finishing
• /
• v.15 no.4
• /
• pp.8-16
• /
• 2003

Poly(trimethylene terephthalate)(PTT) fiber was pretreated with organic solvent/water solution of various compositions. The organic solvents used in this experiment were benzyl alcohol, n-buthanol, and N,N-dimethylformamide(DMF). Density of the fibers were investigated as a measure of crystallite region. The dye uptake increased in the order of pretreatment with hot water < untreated < 5% benzyl alcohol < 100% benzyl alcohol < 90% benzyl alcohol; hot water < untreated $\risingdotseq$ 5% butanol < 100% beutanol < 90% butanol; hot water $\risingdotseq$ 5% DMF < untreated < 90% DMF < 100% DMF. The dye uptake increases with increase of crystallinity. It seems likely that the recrystallization process during the pretreatment with organic solvent/water solutions leads to an increase in the microvoid and then a large increase in the dye uptake. Also the dyeing rate increased and the dyeing transition temperature decreased with the pretreatments. The results obtained are corresponds with the plasticization of the fiber structure formed during the pretreatrnent.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.360-360
• /
• 2006

Zein protein is one of the best biopolymer for edible film making and polyols are convenient plasticizers for biopolymers. Sorbitol, glycerol and manitol at three levels (0.5, 0.7, 1g/g of zein) were used as plasticizers. Rheological and thermal properties of zein resins were studied for determining their plasticization effectiveness. Sorbitol and glycerol had good plasticizing effects and could decrease viscoelastic modulus of zein resins considerably, but manitol was not as effective as them. Effects of plasticizers on thermal properties of resins were investigated by DSC at -100 to $150^{\circ}C$. No crystallization and melting peaks related to zein resin and plasticizers were observed. Thermograms showed that polyolic plasticizers and zein resin remained a homogeneous material throughout the cooling and heating cycles.

• Journal of Korean Ophthalmic Optics Society
• /
• v.17 no.1
• /
• pp.1-10
• /
• 2012

Purpose: Cellulose acetate (CA) was blended with polyethyleneglycol (PEG) having different molecular weight at various mixing conditions to enhance melt-processibility of CA, which might prevent the harmful effect resulted from the introduction of phthalic plasticizer. Methods: To establish optimal plasticizing conditions, CA/PEG blends were examined under various plasticizing conditions: PEG concentration, molecular weight of PEG, and plasticzing temperature. Mechanical properties of the CA/PEG blends, as well as migration and exudation of the PEG, were performed in order to evaluate the efficiency of plasticization. Results: Compared to industrial CA resin plasticized by diethyl phthalate, CA/PEG blends exhibited similar thermal plasticization. It was established that the optimum condition was to blend 30~40 phr PEG with molecular weight 400 at $175{\sim}180^{\circ}C$. CA/PEG blend showed superior glassness, PEG stability, and mechanical properties. Conclusions: CA/PEG blends would be a eco-friendly glasses frame to substitute traditional CA glasses frame prepared phthalate plasticizers.

• Membrane Journal
• /
• v.13 no.4
• /
• pp.246-256
• /
• 2003

For the olefin recovery from polyolefin off-gas, the permeation behaviors of olefins and nitrogen were investigated through three kinds of PDMS membranes - cross-linked PDMS membranes, a polysiloxaneimide membrane, and oligo-PDMS modified PDMS membranes. Their pure gas permeabilities were measured as a function of operation temperature(-20 to $50^{\circ}C$) and pressure(1 to 25 atm) with ethylene($C_2\;H_4$), propylene($C_3\;H_6$), butylene($C_4\;H_8$), and nitrogen($N_2$) gases. The permeabilities of olefins and nitrogen highly depended upon the nature of PDMS membranes. Among these membranes, cross-linked PDMS membranes showed stable and high olefin/nitrogen selectivities over a wide operation pressure range and further study in various test conditions. Their permeability of olefin and nitrogen were governed by the condensation temperature(solubility selectivity) and plasticization, not the order of the size(diffusivity selectivity) of gases, which matched well with the general permeation behavior of rubbery polymeric membranes for condensable and non-condensable gases. With increasing feed pressure or decreasing feed temperature, the permeabilities of more condensible olefins increase highly, presumably due to high solubility and plasticization, but that of non-condensible nitrogen decreases slightly and thus, the selectivities of olefin/nitrogen increase highly.

• Applied Chemistry for Engineering
• /
• v.34 no.3
• /
• pp.252-257
• /
• 2023

In this study, to replace phthalate-based plasticizers known as endocrine disruptors, compounds as plasticizer candidates were synthesized by using alcohols containing rings and fatty acids extracted from animal and vegetable oils, and their properties as plasticizers, including their plasticization efficiency, were evaluated. Nine compounds synthesized by esterification of fatty acids (caprylic acid, capric acid, lauric acid) and alcohols (solketal, benzyl alcohol, cyclohexanol) were identified by ¹H-NMR. The nine synthetic compounds were evaluated for their plasticity by adding them to PVC resin, and compared with the commercial plasticizers DEHP, DINCH, and ESO. According to the results, plasticization efficiency was 0.96 to 1.02 times higher than DEHP, 0.94 to 0.98 times higher than ESO, and 1.05 to 1.10 times higher than DINCH. Thermal stability was somewhat lower than that of DEHP and DINCH, but showed better results than ESO. The results of the solvent extraction test showed that both aqueous and oily solvents showed higher values than DEHP and DINCH but showed similar or superior properties to ESO.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.8 no.2
• /
• pp.39-43
• /
• 2002

Increasing use of plastics in food packaging materials has led to the issue of food-plastic packaging materials's mutual interactions. Although the plastic packaging materials are generally considered as inert, migration and sorption of fatty materials are some of the problems associated with their use. So, this work investigated the compatibility of three structurally different polymers, polypropylene (PP), polyethyleneterephthalate (PET) and ethylene vinyl alcohol copolymer (EVOH) with some structurally different food fats. The main goal was to study the sorption of food fats by the plastic films and to see what extent mechanical properties of the plastic films was affected by plasticization effect due to sorption of fatty materials. PP, PET, and EVOH films was immersed in pure triglycerides, and then extracted with hexane and analyzed for the amounts of fat migrated. The sorbed films were also investigated for change in mechanical properties. Result showed that structural factor of the films and fatty materials plays important role in th migration process. The fat with the simplest structure are migrated more easily that the fat with more complex structure. However, structural effect of migration was varied according to degree of crystallinity and density of plastic films. In addition to that, polarity of plastic film was affected migration of fatty materials significantly. Additional research is needed to justify the reason why migration of fatty materials into the films was affected by polarity and structural integrity.

• International Journal of Concrete Structures and Materials
• /
• v.10 no.3
• /
• pp.373-381
• /
• 2016

As part of this study, has been developed a numerical method which allows to establish abacuses connecting the normal force with bending moment for a circular section and therefore to predict the rupture of this type of section. This may be for reinforced concrete (traditional steel) or concrete reinforced with steel fibers. The numerical simulation was performed in nonlinear elasticity up to exhaustion of the bearing capacity of the section. The rupture modes considered occur by plasticization of the steel or rupture of the concrete (under compressive stresses or tensile stresses). Regarding the fiber-reinforced concrete, the rupture occurs, usually, by tearing of the fibers. The behavior laws of the different materials (concrete and steel) correspond to the real behavior. The influence of several parameters was investigated, namely; diameter of the section, concrete strength, type of steel, percentage of reinforcement and contribution of concrete in tension between two successive cracks of bending. A comparison was made with the behavior of a section considering the conventional diagrams of materials; provided by the BAEL rules. A second comparative study was performed for fibers reinforced section.

• Structural Engineering and Mechanics
• /
• v.91 no.2
• /
• pp.135-147
• /
• 2024

The objective of this study is to analyze, using the finite element method, the durability of damaged and repaired structures under the effect of mechanical loading coupled with environmental conditions (water absorption and/or temperature). The study is based on the hybrid patch repair technique, considering several parameters based on the J integral to observe the behavior of the adhesive in transferring load from a damaged plate to the repair patch. The results clearly show that water absorption and increased temperature cause degradation of the mechanical properties of the adhesive, leading to an increase in its plasticization, which is beneficial for the assembly's strength. However, the degradation of the adhesive's properties due to aging in the repair results in poor load transfer from the damaged area to the patch. The findings of this study allowed the authors to conclude that the [0°]8 sequence consistently offers the best performance, with the lowest J integral values and superior crack resistance. The lowest the J integral for the [0°]8 stacking sequence is typically 3-7% lower than that of the [0/-45/45/90]S and [0/-45/90/45]S sequences at elevated temperatures. At 60℃, the J integral increases by approximately 3-6% compared to 40℃ and 20, depending on the aging duration and stacking sequences.