• 한국공작기계학회논문집
• /
• 제15권6호
• /
• pp.121-126
• /
• 2006

Snap-fit is being used in manufacture of plastic products. Integral features using snap-fit are classified as locks, locators and enhancements. Locking features complete the process of attachment by providing physical interference to prevent separation. Looking feature pairs consist of two components, i.e., a flexible latch and a rigid catch and require particular care and attention for their selection. We can make several locking feature pairs by selecting latch and catch, but some parts restrict freedom of selection. Therefore, part designers must know the characteristic properties of generic locking feature forms as considering a specific design problem. In this paper, it has been presented about problem of small size products using locking feature and then introduced new locking feature applicable to small parts.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.265-268
• /
• 2005

Thermoplastic elastormer (TPE) has many advantages such as high flexibility, high elasticity and high elongation, etc. TPE is easily molded such as plastic materials, therefore, many TPE parts are applied as home appliances and mechanical parts. However, if TPE is once molded, its mechanical properties are changed by injection molding conditions such as melt temperature, mold temperature, injection pressure and holding pressure, etc. In this study, the influences of the injection molding condition on the mechanical properties of thermoplastic vulcanizates(TPVs), which is one of the TPE, were investigated. By the injection molding experiment, as increasing the melt temperature, the tensile strength, shrinkage and hardness decreased. By the scanning electron microscope (SEM) analyzing the TPVs' crystallization, the morphology was affected by the melt temperature.

• 한국금형공학회:학술대회논문집
• /
• 한국금형공학회 2008년도 하계 학술대회
• /
• pp.89-94
• /
• 2008

The injection molding process is a predominant method for producing plastic parts. In order to maximize productivity and molding quality in a injection mold, it is important that each cavity in a multi-cavity injection mold is identical. This requires that cavity dimensions should be identical and delivery system of melt to each cavity have to be the same. Despite the geometrically balanced layout in multi-cavity injection mold more than 4 cavities, it has been observed that the filling in each cavity results in imbalances. Most of cases, this phenomenon of filling imbalances have a bad effect on dimension accuracy, warpage, molding appearance and strength of molding parts. In this study, experiment were conducted to investigate the effect of filling imbalances on the molding quality(surface gloss, shrinkage, tensile strength) in the multy-cavity injection mold.

• Design & Manufacturing
• /
• 제2권2호
• /
• pp.10-14
• /
• 2008

The application range of injection molded parts is expanding by the development of engineering plastics with good mechanical properties. Plastic products are specially used as automotive parts due to an excellent performance in the characteristics of a strength vs. weight. In this study, heating type of new method such as jet injection was applied to improve heat transfer coefficient is substituted for heating method of injection molding.

• 한국방송∙미디어공학회:학술대회논문집
• /
• 한국방송공학회 1999년도 KOBA 방송기술 워크샵 KOBA Broadcasting Technology Workshop
• /
• pp.103.2-110
• /
• 1999

Facial model reconstruction and surgical simulation are essential parts in the computer-aided surgical system. Plastic surgeons use it to design appropriate repair plans and procedures before actual surgery is operated. In this work, the exploration of 3-D metamorphosis to them presents new results in these two parts.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.190-194
• /
• 2001

The integration of rapid prototyping and tooling has the potential for the rapid net shape manufacturing of three-dimensional parts with geometrical complexity. In this study, a new rapid prototyping process, transfer type of Variable Lamination Manufacturing (VLM-ST), was proposed to manufacture net shape of 3-D prototypes. In order to examine the efficiency and applicability of the proposed process, various 3-D parts, such as a world-cup logo, and extruded cross and a knob shape, were fabricated on the apparatus. In addition, the new rapid tooling process, which is a triple reverse process, was proposed to manufacture of 3-D functional part using VLM-ST prototypes and the plastic part of the knob shape was produced by the new rapid tooling process.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 추계학술발표대회 논문집
• /
• pp.153-157
• /
• 2001

Interfacial properties and microfailure modes of electrodeposition (ED) treated carbon fiber reinforced polyetherimide (PEI) toughened epoxy composite were investigated using microdroplet test and the measurement of surface wettability. As PEI content increased, Interfacial shear strength (IFSS) increased due to enhanced toughness and plastic deformation of PEI. In the untreated case, IFSS increased with adding PEI content, and IFSS of pure PEI matrix showed the highest. On the other hand, for ED-treated case IFSS increased with PEI content with rather low improvement rate. The work of adhesion between fiber and matrix was not directly proportional to IFSS for both the untreated and ED-treated cases. The matrix toughness might contribute to IFSS more likely than the surface wettability. Interfacial properties of epoxy-PEI composite can be affected efficiently by both the control of matrix toughness and ED treatment.

• 산업공학
• /
• 제18권1호
• /
• pp.73-81
• /
• 2005

Injection molding has been widely used in producing plastic parts in large quantities. However, its productivity mainly depends on the expertise and experience of skilled workers because of the difficulty and complexity to determine a robust injection molding condition which is not influenced by the minor operational variation of an injection molding machine and produces good parts continuously. This study analyzes the defect types of the parts and proposes a support system to assist users in determining the robust process condition. The support system calculates the start condition from the information of an injection mold, the injection molding machine, the resin used, and the part. Through the iterative step which updates the condition using the defect information of the part tested, users can obtain the initial condition which produces the part without any problem for the first time. The support system also assists users in obtaining the robust condition from the initial condition using the technique of experimental design. To prove the validity of the support system, this study implements it in the control panel of the injection molding machine.

• 대한기계학회논문집A
• /
• 제23권11호
• /
• pp.2087-2095
• /
• 1999

One of the main causes of unwanted dimensional changes in precision metal mold casting parts is excessive and irregular residual stresses induced by temperature gradients and plastic deformation in the solidifying shell. Residual stresses can also cause stress cracking, and lower the fatigue life and fracture strength of the casting parts. In the present study, aluminum alloy casting system with metal mold equipped with electrical heating elements and water cooling units was designed and the casting specimens were produced to quantify the effects of different cooling conditions on the development of residual stresses. The layer removal method was used to measure the biaxial residual stresses in casting specimens produced from the experiments. The experimental results agreed with Tien-Richmond's theoretical model for thermal stress development for the solidifying metal plate.

• 한국정밀공학회지
• /
• 제18권3호
• /
• pp.75-83
• /
• 2001

RIM(Reaction Injection Molding) is a widely used method to manufacture middle-large size outfit-part for a prototype car. The main advantage of RIM is the capability of manufacturing a small number of prototype parts with less cost and lead time than injection molding which is the most popular method to manufacture plastic parts. Generally, epoxy resin and RTV(Room Temperature Vulcanization) silicon are used as mold materials for RIM, and the selection of mold materials is usually depended upon the industrial environment of manufactures and it decides overall mold making process and part quality. This paper suggests a new mold making process by consolidating the advantages of epoxy resin and RTV silicon based RIM mold to enhance the parts quality while reducing the manufacturing cost and time and shows the competitiveness of the suggested process compared with conventional methods.