• 소성∙가공
• /
• 제19권3호
• /
• pp.185-190
• /
• 2010

Application of CAE analyses are wide spread in shaping processes and structural safety verification of plastic products. The importance of CAE analysis and its contributions are getting increase since the processibility and structural safety of product can be predicted. CAE analysis for complex shaped product need a lot of time for modeling and computation compare with simpler one. Therefore careful simulation modeling is required for complex shaped product. Structural analysis for plastic door handle of automobile has been performed and structural safety has been investigated for various load directions and modeling cases. Large stress occurred at the hinge in handle regardless of load direction and modeling case. Consequently hinge is considered structurally very weak among the parts in plastic door handle. It is concluded that simple modeling rather than total modeling with adequate boundary condition equivalent to real situation gives reasonable computational results with saving modeling effort and computation time.

• Earthquakes and Structures
• /
• 제24권1호
• /
• pp.11-20
• /
• 2023

"Performance-based design (PBD)" is based on designing a structure with choosing a performance target under design criteria to increase the structure's resistance against earthquake effect. The plastic hinge formation is determined as one of the fundamental data in finite elements nonlinear analysis to distinguish the condition of the structure where more significant potential damage could occur. If the number of plastic hinges in the structure is increased, the total horizontal load capability of the structure is increased, also. Theoretically, when the number of plastic hinges of the plane frame structure reaches "the degree of hyperstaticity plus one", the structure will reach the capability of the largest ultimate horizontal load. As the number of plastic hinges to be formed in the structure increases towards the theoretical plastic hinge number (TPHN), the total horizontal load capability of the structure increases, proportionally. In the previous studies of the authors, the features of examining the new performance criteria were revealed and it was formulated as follows "Increase the total number of plastic hinges to be formed in the structure to the number of theoretical plastic hinges as much as possible and keep the structure below its targeted performance with related codes". With this new performance criterion, it has been shown that the total lateral load capability of the building is higher than the total lateral load capability obtained with the traditional PBD method by the FEMA 440 and FEMA 356 design guides. In this study, PBD analysis results of structures with frame carrier systems are presented in the light of the Turkey Building Earthquake Code 2019. As a result of this study, it has been shown that the load capability of the structure in the examples of structures with frame carrier system increases by using this new performance criterion presented, compared to the results of the examination with the traditional PBD method in TBEC 2019.

• 한국전산구조공학회논문집
• /
• 제31권6호
• /
• pp.381-388
• /
• 2018

본 논문은 고전적인 오일러-베르누이 보의 집중소성힌지 모델링을 위한 일반유한요소법을 제안한다. 이 기법에서 소성힌지는 해의 약불연속을 묘사하는 적절한 확장함수에 의해 모델링되며, 요소간의 연결성을 변화시키지 않으면서 임의의 위치에 소성힌지를 삽입하는 것이 가능하다. 대신 소성힌지는 이미 존재하는 요소에 위계적으로 자유도를 추가함으로써 형성된다. 제안된 기법의 유효성을 검증하기 위해 수치해석 예제에 대해 h-, p-확장과 같은 수렴성 해석을 수행하였다. 수렴성 해석의 결과가 제안된 기법이 소성힌지가 절점 및 요소 내의 임의의 위치에 존재하는 두 가지 경우 모두에 대하여 유한요소이론에 의한 수렴속도를 얻을 수 있음을 보여주어 기법의 정확성을 입증하였다.

• 한국강구조학회 논문집
• /
• 제12권3호통권46호
• /
• pp.317-328
• /
• 2000

본 연구의 목적은 재료 및 기하학적 비선형을 고려한 고등해석을 이용한 브레이싱된 강뼈대구조물의 최적설계 알고리즘을 개발하는데 있다. 구조물의 해석과정에서 비선형효과를 모두 고려함으로써 기둥의 유효길이 연산이 필요없는 최적설계 알고리즘을 제시하였으며, 전체 구조시스템 및 개별부재의 정보를 이용하여 최적화 하는 2 파라미터형 다단계 최적화 기법을 개발하였다. 해석기법은 단면소성힌지(zero-length plastic hinge) 개념을 이용한 개선된 소성힌지해석법을 수행하였으며, AISC-LRFD '94 규준을 이용하여 최적화 문제를 형성하였다. 본 알고리즘을 브레이싱된 강뼈대구조물에 적용하여 본 연구의 타당성, 효율성, 경제성을 비교검토 하였다.

• 한국지진공학회논문집
• /
• 제12권6호
• /
• pp.1-12
• /
• 2008

국내외의 실험을 통해 알려진 바와 같이 RC교각의 연성능력은 소성힌지구간에 위치한 주철근 겹침이음 비율 및 횡방향 구속철근이 보유한 횡구속력에 따라 차이를 보이고 있다. 내진설계가 반영되지 못한 기존 교각의 경우 소성힌지구간의 겹침이음 비율에 따라 강도 및 연성능력의 저하에 미치는 영향이 크다. 우리나라에서는1992년 내진설계가 도입된 이후 철근콘크리트 교각의 주철근 겹침 이음에 대한 규정은 없었으나, 2005년 도로교 설계기준에서 주철근 겹침이음을 50% 이내에서 허용하고 있다. 기존 교량의 내진성능 평가 요령에 있어서도 이를 반영하여 교각의 연성능력을 평가하고 있지만 주철근 겹침이음 비율을 단순 유 무에 따라서 구분하여 평가하고 있고 평가기법 또한 명확하게 정립되어 있지 못하다. 따라서 본 연구에서는 비내진 교각의 겹침이음 비율별 연성능력평가를 위하여 현재까지 국내에서 수행된 연구실험결과를 분석하고, 교각의 비선형성 및 주철근의 겹침이음을 고려하기 위하여 섬유요소를 이용한 단면해석으로 RC교각의 연성능력을 산정시 적절한 콘크리트의 극한변형률을 제시하였다.

• 대한두개안면성형외과학회지
• /
• 제15권3호
• /
• pp.133-137
• /
• 2014

Reconstruction of a full-thickness alar defect requires independent blood supplies to the inner and outer surfaces. Because of this, secondary operations are commonly needed for the division of skin flap from its origin. Here, we report a single-stage reconstruction of full-thickness alar defect, which was made possible by the use of a nasolabial island flap and septal mucosal hinge flap. A 49-year-old female had presented with a squamous cell carcinoma of the right ala which was invading through the mucosa. The lesion was excised with a 5-mm free margin through the full-thickness of ala. The lining and cartilage was restored using a septal mucosa hinge flap and a conchal cartilage from the ipsilateral ear. The superficial surface was covered with a nasolabial island flap based on a perforator from the angular artery. The three separate tissue layers were reconstructed as a single subunit, and no secondary operations were necessary. Single-stage reconstruction of the alar subunit was made possible by the use of a nasolabial island flap and septal mucosal hinge flap. Further studies are needed to compare long-term outcomes following single-stage and multi-stage reconstructions.

• Steel and Composite Structures
• /
• 제31권3호
• /
• pp.319-327
• /
• 2019

This paper describes an experimental study of steel beam-column connections with or without expanded beam flanges with different geometries. The objectives of this study are to elucidate the cyclic behavior of these connections, identify the location of the plastic hinge zone, and provide useful test data for future numerical simulations. Five connection specimens are designed and tested under cyclic load. The test setup consists of a beam and a column connected together by a connection with or without expanded beam flanges. A constant axial force is applied to the column and a time varying point load is applied to the free end of the beam, inducing shear and moment in the connection. Because the only effect to be studied in the present work is the expanded beam flange, the sizes of the beam and column as well as the magnitude of the axial force in the column are kept constant. However, the length, width and shape of the expanded beam flanges are varied. The responses of these connections in terms of their hysteretic behavior, failure modes, stiffness degradation and strain variations are experimentally obtained and discussed. The test results show that while the influence of the expanded beam flanges on hysteretic behavior, stiffness degradation and energy dissipation capacity of the connection is relatively minor, the size of the expanded beam flanges does affect the location of the plastic hinge zone and strain variations in these beam-column joints. Furthermore, in terms of ductility, moment and rotational capacities, all five connections behave well. No weld fracture or premature failure occurs before the formation of a plastic hinge in the beam.

• Earthquakes and Structures
• /
• 제26권3호
• /
• pp.175-189
• /
• 2024

Aiming at studying the plastic hinge (PH) evolution regularities and failure mode of rocking wall moment frame (RWMF) structure in earthquakes, the whole-working history analysis of seismic performance state of RWMF structure based on co-operation performance and PH evolution was carried out. Building upon the theoretical analysis of the elastic internal forces and deformations of RWMF structures, nonlinear finite element analysis (FEA) methods were employed to perform both Pushover analysis and seismic response time history analysis under different seismic coefficients (δ). The relationships among PH occurrence ratios (R_ph), inter-story drifts and δ were established. Based on the plotted curve of the seismic performance states, evaluation limits for the R_ph and inter-story drifts were provided for different performance states of RWMF structures. The results indicate that the R_ph of RWMF structures exhibits a nonlinear evolution trend of "fast at first, then slow" with the increasing of δ. The general pattern is characterized by the initial development of beam hinges in the middle stories, followed by the development towards the top and bottom stories until the beam hinges are fully formed. Subsequently, the development of column hinges shifts from the bottom and top stories towards the middle stories of the structure, ultimately leading to the loss of seismic lateral capacity with a failure mode of partial beam yield, demonstrating a global yielding pattern. Moreover, the limits for the R_ph and inter-story drifts effectively evaluate the five different performance states of RWMF structures.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2000년도 춘계 학술발표회 논문집 Proceedings of EESK Conference-Spring
• /
• pp.335-340
• /
• 2000

The influence of lap splice of longitudinal bars in the plastic hinge zone on the nonlinear behavior characteristics of RC piers has been investigated through the scale model tests. The seismic performance of bridge piers with lap splice is found to be insufficient due to the premature bond failure. On the other hand it is confirmed that the preventing lap splice in the plastic hinge zone enhance the seismic performance considerably even without the seismic details of transverse reinforcements. Bases on these experimental results new seismic detailing concept appropriate to moderate seismicity region has been proposed.

• 한국구조물진단유지관리공학회 논문집
• /
• 제3권1호
• /
• pp.137-146
• /
• 1999

Analysis of R/C columns requires modeling of the plastic hinge region, as well as nonlinear material characteristics. This becomes a challenging task in view of the nonlinearity of both steel and concrete. Furthermore, formation and progression of plasticity in the hinge is a difficult phenomenan to simulate, especially under reversed cyclic loading and decaying strength conditions. This research provide one analytical model employed in column analysis, including the analysis procedure for establishing inelastic force-deformation relationships. The analytical results show good correlation with experimental data. The employed procedure with the adopted analytical models can be used to compute inelastic displacements of concrete columns with welded reinforcement grids. The inelastic deformability beyond the peak was similar to those indicated by columns with conventional ties. The superior performance of columns with welded grids may be attributed to the improved confinement characteristics of grids associated with increased rigidity of welded ties.