• Journal of the Korean Magnetics Society
• /
• v.13 no.1
• /
• pp.29-35
• /
• 2003

Anisotropic Sr-ferrites were prepared by the spark plasma sintering process (SPS). The Ferrite particles were oriented and densified during sintering process, and the anisotropic ferrites were manufactured at low sintering temperature and a remarkable short time processing by SPS method. It was showed that the anisotropy of ferrite particles at the specimen outer side was more higher than that at the specimen center, and it seems possible that the orientation of ferrite particles was related to DC current. Magnetic and physical properties of sintered Sr-ferrites are Br = 3.15 kG, iHc : 2.67 kOe, and density : 5.033 g/cm$^3$ when the samples were sintered for 8 minutes at 106$0^{\circ}C$.

• Journal of Powder Materials
• /
• v.16 no.1
• /
• pp.63-67
• /
• 2009

In order to investigate the effect of rapid solidification on the microstructure and the mechanical properties of Al-Zn-Mg system alloys, water atomization was carried out, since the water atomization beared the highest solidification rate among the atomization processes. The as atomized alloy powders consisted of fine grains less than 4 ${\mu}m$ in diameter, and the second particles were not detected on XRD. The microstructure as solidified was maintained even after the spark plasma sintering at the heating rate of 50 K/min. On the other hand, lower rate of 20 K/min induced a formation of $MgZn_2$ particles, resulting in strengthening of the matrix. The density was almost constant at the temperature above 698K. The sintering temperature above 698K had no effect on the strength of the sintered materials.

• Journal of Powder Materials
• /
• v.21 no.2
• /
• pp.137-141
• /
• 2014

In this study, we report the sintering behavior and properties of a $Ge_2Sb_2Te_5$ alloy powders for use as a sputtering target by spark plasma sintering. The effect of various sintering parameters, such as pressure, temperature and time, on the density and hardness of the target has been investigated in detail. Structural characterization was performed by scanning electron microscopy and X-ray diffraction. Hardness and thermal properties were measured by differential scanning calorimetry and micro-vickers hardness tester. The density and hardness of the sintered $Ge_2Sb_2Te_5$ materials were 5.8976~6.3687 $g/cm^3$ and 32~75 Hv, respectively.

• Korean Journal of Materials Research
• /
• v.17 no.8
• /
• pp.397-401
• /
• 2007

Fe based SOFC(Solid Oxide Fuel Cell) interconnector was fabricated by using the spark plasma sintering process and its microstructure and mechanical properties were investigated in this study. To fabricate the interconnector, the Fe-26Cr powder was mixed with the Ag (5, 10, 20wt.%) particles. In the Fe-26Cr-Ag sintered bodies, the Ag particles were almost dispersed at the grain boundary of the Fe-26Cr. The sintered bodies have the density of 87.2-97.5%, the density increases with increasing Ag content at sintering temperature of $850^{\circ}C$. Also, the compressive yield strength increases with increasing Ag content at the same sintering temperature.

• Journal of Powder Materials
• /
• v.10 no.3
• /
• pp.172-175
• /
• 2003

Mechanically-alloyed NiAl powder was sintered by Spark-Plasma Sintering (SPS) process. Densification and behavior mechanical property were determined from the experimental results and analysis ,such as changes in linear shrinkage, shrinkage rate, microstructure, and phase during sintering process, Victors hardness, and transver.ie-rupture-strength (TRS). Above 97% relative density was obtained after sintering at 115$0^{\circ}C$ for 5 min. Crystallite size determined by the Scherrer method was approximately 50 nm. From the X-ray diffraction analysis it was confirmed that the sintered bodies were composed mainly of NiAl phase together with Ni$_3$Al phase. Measured Vickers hardness and TRS value were 555$\pm$10 $H_v$ and 1393$\pm$75 MPa , respectively.

• Korean Journal of Materials Research
• /
• v.15 no.12
• /
• pp.765-772
• /
• 2005

PAS(Plasma Activated Sintering) process was tried to apply for the fabrication of BMG(Bulk Metallic Glasses) of $Ni_{57}Zr_{20}Ti_{18}Si_5}\;and\;Ni_{57}Zr_{20}Ti_{18}Si_3Sn_2$ from the as-atomized amorphous powder. Compressive strength for the BMG(bulk Metallic Glasses) of $Ni_{57}Zr_{20}Ti_{18}Si_5$ were lower than those of BMG rods produced by warm extrusion ,or copper mold casting method. Microstructural examination by optical microcope, SEM ana EDS showed that oxidation had occurred during PASintering. In order to prevent the powder from the oxidation during PASintering, Ni coating for $Ni_{57}Zr_{20}Ti_{18}Si_5$ amorphous powder by electroless-plating method was performed. Microstructural examination for Ni coated layers after PASintering indicated that the Ni coating had been so effective to prevent powder from oxidation during PASintering. Sintering behaviors of $Ni_{57}Zr_{20}Ti_{18}Si_3Sn_2$ represent the same as those of $Ni_{57}Zr_{20}Ti_{18}Si_5$.

• Korean Journal of Metals and Materials
• /
• v.50 no.6
• /
• pp.469-475
• /
• 2012

A high-energy mechanical milling (HEMM) process was introduced to improve sinter-ability, and rapid sintering of spark plasma sintering (SPS) under pressure was used to make ultra fine grain (UFG) of Ti-Nb-Mo-CPP composites, which have bio-attractive elements, for increasing mechanical properties. Ti-Nb-Mo-CPP composites were successfully fabricated by SPS at $1000^{\circ}C$ within 5 minutes under 70 MPa using HEMMed powders. The Vickers hardness of the composites increased with increased milling time and addition of CPP contents. Biocompatibility and corrosion resistance of the Ti-Nb-Mo alloys were improved by addition of CPP, and the Ti-35%Nb-10%Mo-10%CPP alloy had better biocompatibility and corrosion resistance than the Ti-6Al-4V ELI alloy.

• Journal of Ceramic Processing Research
• /
• v.19 no.5
• /
• pp.383-387
• /
• 2018

Highly transparent $Y_2O_3$ ceramics were produced using spark plasma sintering (SPS) at $1600^{\circ}C$ and 30 MPa for 5 min. When the SPS process was applied with various amounts of $La_2O_3$ as dopant. The specimen doped with 3 mol% $La_2O_3$ showed the highest density, and rapid particle growth and pore growth occurred, exhibiting that the relative density and average grain size are 99.2% and $17.2{\mu}m$, respectively. The specimen showed excellent transmittance of 79.44% in the visible light region (600 nm), resulting that $La_2O_3$ would be a useful dopant for improving the transmittance and mechanical properties of transparent $Y_2O_3$ ceramics produced with SPS.

• Journal of the Korean Society for Heat Treatment
• /
• v.33 no.4
• /
• pp.185-192
• /
• 2020

In this study, materials characterization of pure copper and copper based carbon nano-tube composite prepared by powder metallurgy method were investigated. Prior to evaluate materials characterization, spark plasma sintering processing variables such as sintering temperature, pressure, thickness and diameter of compacts was optimized to ensure the microstructure and materials property of pure Cu and Cu-CNT composite. In addition, corrosion behavior of Cu-based CNT composite produced by powder sintering method was investigated. It was confirmed from this study that the corroded surfaces of the composite shows less dissolution compared with pure copper in 3.5 wt% NaCl solution. The measured corrosion current density (I_corr) indicates improved corrosion property of Cu based composite containing small additions of CNTs in chloride containing media. Micro-galvanic activity between Cu and CNT was not observed in given sintering condition.

• Korean Journal of Materials Research
• /
• v.18 no.4
• /
• pp.181-186
• /
• 2008

In this study, tantalum (Ta) compacts were fabricated in a spark plasma sintering (SPS) process and their microstructure and mechanical properties were investigated. Ta compacts with a density of 99% were successfully fabricated by controlling the sintering conditions of the current and the temperature. The density and hardness were increased as the sintering temperature increased. The $Ta_2C$ compound was observed at the surface of the compacts due to the contact between the Ta powder and graphite mold during the sintering process. The main fracture mode showed a mixed type with intergranular and transgranular modes having some roughness.