• 한국항해항만학회지
• /
• 제40권5호
• /
• pp.231-239
• /
• 2016

In general, the attitude of a high-speed planning boat changes following a speed change. Since the hydrodynamic forces acting on a ship differ according to the change of its underwater shape, it is difficult to estimate its hydrodynamic force compared to that of a large commercial ship. In this paper, 6 Degrees Of Freedom (DOF) equations of motion that express the maneuvering motion of a planning boat are modeled by analyzing its motion characteristics based on various sea trial tests. Finally, a maneuvering simulation is carried out and a validation of the equations of motion is confirmed with the results of sea trial tests.

• 한국해양공학회지
• /
• 제22권4호
• /
• pp.84-89
• /
• 2008

It is hard to find experimental data for a model test of small high-speed planning boats. It is difficult to verify the performance seen in a model test for a high-speed boat because the ship-model scale-ratio is very small and the flow velocity of the circulating water channel and the X-carriage speed of the towing tank are restricted. Therefore most hull-form designs for high-speed small boats depend on the sea-trial test result for similar boats or evaluation through numerical calculations. This study investigated the anti-rolling effect of the stern sub-body in a 50-knot doss planning boat. To carry out this work, new model test procedures were set up in the actual sea. Using this method, the anti-rolling effect of the stern sub-body was investigated. A stern sub-body attached to a planning boat was proved to be effective in reducing the roll and pitch angle.

• 동력기계공학회지
• /
• 제16권4호
• /
• pp.17-23
• /
• 2012

In this study, the numerical simulation and basin model test have been performed to evaluate sea worthiness and resistance performance for a small pre-planning three type of leisure boats which are U, V, Y shapes of hull forms. As a well known commercial CFD code, Maxsurf, was applied for modeling hull forms used as the solver of motion analysis. Also the model resistance test was carried out to estimate the effective power of boat in the basin tank. Numerical simulation and model test results show that Y-shaped hull is better than the other types in terms of heave and pitch motion, having a key effect on a boat sea worthiness. But V-type hull is more efficiency than others cases in resistance performance.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 추계학술발표대회 개요집
• /
• pp.213-215
• /
• 2004

Water jet propulsion system has high efficiency on middle to high speed, and it provides better safety than conventional screw propeller because it has not projected propeller and rudder. So many leisure boat and high-speed ferries use this propulsion system. We developed water-jet propulsion unit for small planning boat, and launched that in the boat, after that we tested water-jet unit in the lake. As a result, we certify heat dissipation at the bearing housing and reverse duct's shape for neutral position are important at the design, and alignment water-jet unit and keel line are important at the launching, and ship's resistance performance and jet's propulsion performance also are needed to consideration.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 춘계학술대회 논문집
• /
• pp.221-224
• /
• 2003

This study was carried out to develope a basic form of planning hull type fishing boat. G/T 10ton class is selected as object hull form, and hull form is designed in Chosun University. A series of test results of LCG variations for 5 different LCG points are presented in this paper. The test was performed in Davidson Laboratory, and the scope of tests include resistance, trim and sinkage.

• 한국항해항만학회지
• /
• 제31권10호
• /
• pp.813-818
• /
• 2007

선박의 선형시험설비로는 회류수조, 예인수조 등이 있으나, 소형 고속선박은 실선 대응 모형선의 축적비가 대형선에 비해 매우 작고 수조의 유속과 예인전차의 속도제한으로 고속선의 설계선속까지의 성능검증에는 한계로 작용하였다. 이에, 고속 활주형선의 선형시험 검증을 위해 실 해상모형시험기법을 정립하였다. 한편, 고속 Stepped Hull선형은 일체형 활주형 선저선형에 비하여 고속 주행시 공기공급에 따른 접수면 감소로 인하여 저항감소에 따른 속도향상과 연비절감 효과가 있으나, 선미 좌우측의 접수면 감소에 따른 횡동요 안정성이 감소되는 경향이 있다. 이에, 본 논문에서는 고속 선형시험이 가능한 해상모형시험을 이용하여 선미 보조동체 장착 유무에 따른 고속 Stepped Hull 선형의 횡동요 및 저항특성을 비교, 분석한 것이다.

• 수산해양기술연구
• /
• 제44권1호
• /
• pp.68-74
• /
• 2008

This study is concerned with the development of the basic planing hull form of small fishing boat in 25 knots high speed. A series of model test to determine the optimum performance hull form of actual fishing boat with 10 gross tonnage was carried out for 5 models made available planing hull form in the circulation water channel. Model test was performed with the resistance test to study the hydrodynamic characteristics of model ships and the sinkage and trim measurement to investigate the stability of model ships and also the wave pattern observation to analyze the effectiveness of model ships. As the result, the planing hull form of P-4 with deep V type bow can be derived as the best hull form with good performance especially in ship's resistance efficiency showing less residual resistance and sinkage and trim and the spray effect, etc..

• 한국해양공학회지
• /
• 제18권3호
• /
• pp.44-49
• /
• 2004

Initial hull form of 10 G/T and 40 knots class coastal patrol boat is newly developed. The resistance performances are experimentally and numerically investigated by model test and CFD technique. The effect of initial trim and a fin attached at hull side are studied together. Wave patterns are observed to make clear the relation between the performance and the wave characteristics. It can be found that the initial trim plays a role in increasing the resistance performance above a certain velocity, and the CFD technique can be used at the initial design stage of a high-speed planning boats.

• Journal of Ship and Ocean Technology
• /
• 제9권2호
• /
• pp.1-10
• /
• 2005

A light-weight cantilever type towing carriage was devised and installed in the towing tank at Seoul National University. Wireless measurement devices were also provided for appropriate data acquisition during high-speed towing tests. With the new carriage system, a series of model tests were performed to investigate the hydrodynamic characteristics of the racing boat in the towing tank and the resistance test results had sufficient accuracy so that they could be used in the development of a high speed planning hull.

• 한국해양공학회지
• /
• 제22권2호
• /
• pp.91-98
• /
• 2008

In order to establish a design guide for the bottom plate structure of a 4.3 ton aluminum planning boat, the feasibilities of bottom plate scantling of the ship are investigated based on the results of structural strength analysis and a simple equation and evaluation system are developed for initial structural design purposes. This study consists of 5 steps: First, the background, necessity, and purpose of this study are explained briefly, Second, the principal dimensions of this ship, the position of the considered bottom plate members and material characteristics are introduced. Third, the equivalent design pressure concept is introduced and evaluated based on experience and experimental data. Fourth, the strength of bottom plate members are examined using elasto-plastic nonlinear structural analysis, and response levels and several boundary conditions are reviewed based on the analysis results. Finally, in order to suggest design guides in respect to the ship's structural design, a simple design equation and evaluation system for bottom plate members are suggested for boats in the 4.3 ton aluminumboat range through the introduction of safety factorsbased on the ultimate design pressure concept.