• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.3C
• /
• pp.127-136
• /
• 2009

The objective of this study is the development and verification of the 4-electrode resistivity probe (4ERP) for the estimation of electrical properties of the saturated soils. The 4ERPs with wedge and plane types are manufactured to obtain the electrical resistivity without polarization at the electrodes by using Wenner array. The wedge type is for the penetration into the soil samples and the plane type is for the installation into the cells used for the laboratory tests. The consolidation tests are carried out by using 6 types of glass beads and 3 types of sands in size. The test results show that the electrical resistivity increases with a decrease in the porosity, and the constant m used in Archie's law is dependent on the particle shape rather particle size. The one dimensional liquefaction tests show that the porosity obtained by the 4ERP is similar to that determined by the volume fraction. The penetration of the 4ERP into the large scale calibration chamber produces the resistivity profiles. This study demonstrates that the 4ERP may effectively estimate the porosity of the saturated soils.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.1
• /
• pp.38-45
• /
• 2010

A new readout circuit involving a pixel-level reset control was studied for 2-D long wavelength infrared focal plane arrays. The integration time of each pixel can be optimized individually and automatically. Hence, the readout circuit has a wide dynamic range and good signal-to-noise ratio characteristics. The readout circuit was fabricated with a $0.35{\mu}m$ 2-poly 4-metal CMOS process for a $128{\times}128$ long wavelength infrared HgCdTe array with a pixel size of $50{\mu}m{\times}50{\mu}m$. The smart reset control with two-step background suppression improves the signal-to-noise ratio to 87dB and the dynamic range to 95.8dB.

• Journal of Sensor Science and Technology
• /
• v.27 no.5
• /
• pp.311-316
• /
• 2018

An antenna-coupled bolometer-type terahertz sensor was designed, fabricated, evaluated, and utilized to obtain terahertz transmission images. The sensor consists of a thin film bowtie antenna that resonates accordingly in response to an incident terahertz beam, a heater that converts the applied current in the antenna into heat, and a microbolometer that converts the rise in temperature into a change in resistance. The device is fabricated by a bulk micromachining process on a 4-inch silicon wafer. The fabricated sensor chip has a size of $2{\times}2mm$ and an active area of $0.1{\times}0.1mm^2$. The temperature coefficient of resistance (TCR) of the bolometer film (VOx) is 2.0%, which is acceptable for bolometer applications. The output sensor signal is proportional to the power of the incident terahertz beam. Transmission images were obtained with a 2-axis scanning imaging system that contained the sensor. The small active area of the sensor will enable the development of highly sensitive focal plane array sensors in terahertz imaging cameras in the future.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.3
• /
• pp.209-216
• /
• 2003

We design and fabricate slot array antenna for BMWS(Broadband Multimedia Wireless System) applications. This paper presents a simple feed structure, which consists of two horns and a parallel-plate waveguide, because antennas operating at 40.5 GHz~43.5 GHz have considerable feeding losses. The simple feed structure has the advantages of high-efficiency and mass-production. The fabricated antenna has a gain of 25.8 dBi with a sidelobe level below -18 ㏈ and a 3 ㏈ beamwidth of approximately 3$^{\circ}$ in the E-plane. In case of H-plane, a 3 ㏈ beamwidth is 17$^{\circ}$ and a sidelobe level is suppressed to below -27 ㏈. The experimental results are in good agreement with the simulation results. The authors expect that narrow 3 ㏈ beamwidth is obtained by combining a few proposed slot array antennas in parallel.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.3
• /
• pp.273-279
• /
• 2009

In this paper, an antenna which has dipole-like radiation pattern and low profile is proposed. The antenna is composed of four elements slot array based on L-shaped 0.43 $\lambda_g$ slot element. It presents a omni-directional radiation patter in the azimuth plane and has a null toward broad-side direction. In the design, a small mono-pole antenna which acts as a large capacitance element, combined with the partially removed ground plane by four L-shaped slots. As a result, these structure act as a LC resonator for radiation. The measured result shows, the impedance bandwidth(VSWR$\leq$2) of the proposed antenna is 60 MHz(2.35$\sim$2.41 GHz). The measured maximum radiation gain and efficiency of proposed antenna is 0.02 dBi, 56.7 % at center frequency 2.38 GHz, respectively. The proposed antenna can be applied to wireless tan access point system.

• Advanced Industrial SCIence
• /
• v.3 no.2
• /
• pp.31-37
• /
• 2024

This paper presents a single and 2-patch microstrip array antenna operated on a frequency of 10.3GHz(x-band). It outlines the process of designing a microstrip patch array antenna using CST MWS. Initially, a single microstrip antenna was designed, followed by optimization using CST MWS to attain optimal return losses and gain. Subsequently, the design was expanded to create a 2×1 microstrip inset-fed array antenna for the X-band applications. The construction material is Roger RO4350B, with specific dimensions (h=0.79mm, 𝜖_r = 3.54). The achieved results include an S11 of -18dB at the resonant frequency (10.3GHz), a gain of 9.82dBi, a bandwidth of 0.165GHz, and a 3-dB beamwidth of 30°, 121° in Az(𝜑=0) and El(𝜑=90) plane, respectively. The future plan involves the fabrication of this array antenna and further expansion to a 4×4 array of microstrip antennas. It is then incorporated on the X-band applications for practical uses.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.2
• /
• pp.95-104
• /
• 2011

In this paper, the metamaterial transmission line (TL) based on the complementary spiral resonators (CSRs) and interdigital structure is presented for reducing the phase noise of the voltage-controlled oscillator (VCO). The metamaterial TL is realized by adopting the array of the CSRs etched on the ground plane and the interdigital transmission line on the signal plane. The interdigital TL on the signal plane has been used to obtain higher Q value than the conventional TL without the interdigital structure. The resonance properties and inherent saturation of Q value of the proposed metamaterial TL have been analyzed by varying the width of the TL on the signal plane, dimensions of the CSRs, current directions between the CSRs, number of the unit cell-pair of the CSRs, and whether or not there is the interdigital structure in this paper. The phase noise and tuning range of the proposed VCO are -127.50~-125.33 dBc/Hz at 100 kHz and 5.744~5.852 GHz.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.12
• /
• pp.17-26
• /
• 1998

Ultrasonic sensors are widely used in various applications due to advantages of low cost, simplicity in construction, mechanical robustness, and little environmental restriction in usage. But for the application of object recognition, ultrasonic sensors exhibit several shortcomings of poor directionality which results in low spatial resolution of objects, and specularity which gives frequent erroneous range readings. The time-of-flight(TOF) method generally used for distance measurement can not distinguish small object patterns of plane, corner or edge. To resolve the problem, an increased number of the sensors in the forms of a linear array or 2-dimensional array of the sensors has been used. Also better resolution has been obtained by shifting the array in several steps using mechanical actuators. Also simple patterns are classified based on analyzing signal reflections. In this paper we propose a method of a sensor array system with improved capability in pattern distinction using electronic circuits accompanying the sensor array, and intelligent algorithm based on neuro-fuzzy processing of data fusion. The circuit changes transmitter output voltages of array elements in several steps. A set of different return signals from neighborhood sensors is manipulated to provide enhanced pattern recognition in the aspects of inclination angle, size and shift as well as distance of objects. The results show improved resolution of the measurements for smaller targets.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.7
• /
• pp.534-538
• /
• 2013

We propose a generic method to calculate the optical functionalities of a 3D display with a lenticular lens array. In the present work, based on the geometrical optics, it is designed considering the specifications of the display panel. For the effective simulation, we first calculate the optical functionalities of a single cylindrical lens and, by comparing with the results obtained from the conventional geometrical optics, confirm the validity of the present method. Afterwards, we obtain the full distribution of the light intensity at an optimum viewing distance by expanding the results of the single lens to the horizontal plane of the display panel. From these results, we finally confirm whether the 3D images are realized or not in the system.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1617-1620
• /
• 2007

This paper presents a magnetostrictive transpositioner and its fabrication process. To get a transposition movement without shifting or twisting, it is designed as an array type. To fabricate the suggested design, micromachining and selective DC magnetron sputtering processes are combined. TbDyFe film is sputter-deposited on the back side of the bulk micromachined transpositioner, with the condition as: Ar gas pressure below $1.2{\times}10^{-9}$ torr, DC input power of 180W and heating temperature of up to $250^{\circ}C$ for the wireless control of each array component. After the sputter process, magnetization and magnetostriction of each sample are measured. X-ray diffraction studies are also carried out to determine the film structure and thickness of the sputtered film. For the operation, each component of the actuator has same length and out-of-plane motion. Each component is actuated by externally applied magnetic fields up to 0.5T and motion of the device made upward movement. As a result, deflections of the device due to the movement for the external magnetic fields are observed.