• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.354-357
• /
• 2001

The residual DC properties in the in-plane switching (IPS) liquid crystal displays(LCDs) which have different concentrations of cynao NLCs and different resistivities of fluorine NLCs were studied. We also propose a new residual DC measurement method, named 'light minimum/maximum method'. We confirmed the precision of residual DC measurement by light minimum/maximum method compared with the flicker minimizing method and found that new measurement method of residual DC is better than that of the conventional flicker minimizing method since the resolution level of measurements is in 0.1 V

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.445-447
• /
• 2000

The terminal and core(wire conductor) in a Harness processing is connected by putting them in a applicator by virtue of a manual operation. A normal or abnormal condition of crimping connections is nearly determined by a skilled worker. In general, a skilled worker operates a press motor with a foot switch by pressing on foot and puts a wire conductor into a press with one hand. By doing so, sufficient efficiency is not obtained by a worker. In this paper, a basic study has done to make improve an efficiency by finding the normal arrangement out as to whether a terminal and wire conductor in Harness are placed on the right position or not with a quadrant plane photo position sensor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.2
• /
• pp.153-158
• /
• 2010

The crystallization of FePt/MgO(001) magnetic thin films of various thicknesses has been studied using synchrotron x-ray scattering, atomic force microscope, and vibrating sample magnetometer. In film with a 499-$\AA$-thick, face-centered tetragonal, ordered FePt phase was dominantly crystallized into perpendicular (001) grains keeping the magnetically easy c-axis normal to the film plane during annealing. In film with a 816-$\AA$-thick, however, longitudinal (110) grains keeping the c-axis parallel to the film plane were grown on top of the perpendicular (001) grains. The behavior of the magnetic properties was consistent with the thickness dependence of the crystallization. We attribute the thickness dependence of the crystallization to the substrate effect, which prefers the growth of the c-axis oriented perpendicular grains near the film/substrate interfacial area.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.5-8
• /
• 1997

A study on the electrical conduction characteristics of the ultrathin organic films is one of the important factors for the development of molecular electronic devices. The Langmuir- Blodgett(LB) technique has recently been attracted interest as a method of the deposition ultrathin films. We hate fabricated N-docosyl N\`-methyl viologen-diTCNQ(DMVT) anion radical LB film and investigated the molecular orientation and electrical conduction characteristics. We have measured infrared transmission-reflection spectra. The alkyl chain is found to he well-ordered with the tilt angle of 13$^{\circ}$ with respect to the substrate surface normal and the TCNQ plane is tilted at 76$^{\circ}$ the surface normal. In ESR spectrum, we confirmed that a half-amplitude linewidth is clearly dependent on the incident angle, which indicates conducting species change. The in-plane conductivity of 31 lagers is approximately 1.33$\times$10$^{-6}$ S/cm. The ohmic behaviour was observed below 0.6 V, when current-voltage(I-V) characteristics was measured verically.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.453-454
• /
• 2006

We studied the nematic liquid crystal (NLC) alignment capability by the IB(Ion bean) alignment method on a NDLC(Nitrogen Diamond Like Carbon) as a-C:H thin film. and investigated electro-optical performances of the IBaligned IPS(In plane switching)cell with NDLC surface. A good LC alignment by IB exposure on a NDLC surface was achieved. Monodomain alignment of the IB aligned IPS cell can be observed. The goodelectro-optical (EO) characteristics of the IB aligned IPS cell was observed with oblique IBexposure on the NDLC as a-C:H thin film for 1 min.

• Design & Manufacturing
• /
• v.15 no.3
• /
• pp.19-25
• /
• 2021

The bending process of a press die is to bend a flat blank to the required angle. There are V-bending, U-bending, Z-bending, O-bending etc. for bending processing, and the basic principle of calculating the unfolding length of die processing is used as the neutral plane length. Since the constant of the length value of the neutral surface is different depending on the type of bending, it is impossible to accurately calculate it. In particular, Z-bending processing is performed twice, and it is set on the upper and lower surfaces of the blank, and bending processing occurs at the same time as the upward and downward bending, and the elongation of the material occurs and the material increases. It is not possible to check with the calculated value, and it occurs in many cases where the mold is modified after start-up. This study aims to minimize die modification by developing a formula to calculate the development length of Z-bend.

• Structural Engineering and Mechanics
• /
• v.87 no.1
• /
• pp.95-106
• /
• 2023

This paper investigates the dynamic response of a functionally graded material (FGM) coated half-plane excited by distributed time harmonic loading. Three types of typical distributed surface loads, including uniform load, Hertz load, and square-root singular load, are considered. The mass density and elastic modulus of the FGM coating are supposed to be described by the exponential function. The material damping is modelled by a linearly hysteretic damping which is expressed by a complex modulus in the time harmonic motion. Using Fourier integral transform technique and numerical integral method, the effects of the excitation frequency, gradient index, damping, and load type on the dynamic stresses and displacements are discussed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.4 s.247
• /
• pp.393-401
• /
• 2006

The influences of stress triaxiality on ductile fracture have been investigated for various specimens and structures. With respect to a transferability issue, recently, the interests on local approaches reflecting micromechanical specifics are increased again due to rapid progress of computational environments. In this paper, the applicability of the local approaches has been examined through a series of finite element analyses incorporating modified GTN and Rousselier models as well as fracture toughness tests. The ductile crack growth of nuclear carbon steels is assessed to verify the transferability among compact tension (CT) specimens with different in-plane size. At first, the basic material constants were calibrated for standard CT specimens and used to predict fracture resistance (J-R) curves of larger CT specimens. Then, the in-plane size effects were examined by comparing the numerically estimated J-R curves with the experimentally determined ones. The assessment results showed that the in-plane size effect should be considered for realistic engineering application and the damage models might be used as useful tool for ductile fracture evaluation.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.169-178
• /
• 1991

A plane-strain finite element analysis of sheet metal forming is carried out by using the rigid-plastic FEM based on the membrane theory. The sheet material is assumed to possess normal anisotropy and to obey Hill's new yield criterion and its associated flow rule. A formulation of initial guess generation for the displacement field is derived by using the nonlinear elastic FEM. A method of contact treatment is proposed in which the skew boundary condition for arbitrarily shaped tools is successively used during iteration. In order to verify the validity of the developed method, plane-strain drawing with tools in analytic expression and with arbitrarily shaped tools is analyzed and compared with the published results. The comparison shows that the present method can be effectively used in the analysis of plane-strain sheet metal forming and thus provides the basis of approximate sectional analysis of panel-like sheet forming.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.12 no.2
• /
• pp.171-176
• /
• 2002

This paper describes a new automated analysis system for model plane engine. An automatic finite element (FE) mesh generation technique, which is based on the fuzzy knowledge processing and computational geometry technique, is incorporated into the system, together with one of commercial FE analysis codes, ANSYS, and one of commercial solid modelers, Designbase, The system allows a geometry model of concern to be automatically converted to different FE models, depending on physical phenomena of plane engine to be analyzed, i.e. deformation analysis, thermal analysis and so on. The FE models are then automatically analyzed by the FE analysis code. Among a whole process of analysis, the definition of a geometry model, the designation of local node patterns, the assignment of material properties and boundary conditions onto the geometry model are only the interactive processes to be done by a user. The interactive operations can be processed in a few minutes. The other processes which are time consuming and labour-intensive in conventional CAE systems are fully automatically performed in a personal computer environment. The proposed analysis system is successfully applied to evaluate a model plane entwine.