• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.136-136
• /
• 2003

In fiber optic networks, system size and cost can be significantly reduced by development of optical components through planar optical waveguides. One important step to realize the compact optical devices is to develop planar optical amplifier to compensate the losses in splitter or other components. Planar amplifier provides optical gain in devices less than tens of centimeters long, as opposed to fiber amplifiers with lengths of typically tens of meters. To achieve the same amount of gain between the planar and fiber optical amplifier, much higher Er doping levels responsible for the gain than in the fiber amplifier are required due to the reduced path length. These doping must be done without the loss of homogeniety to minimize Er ion-ion interactions which reduce gain by co-operative upconversion. Sol-gel process has become a feasible method to allow the incorporation of Er ion concentrations higher than conventional glass melting methods. In this work, Er-doped $SiO_2$-A1$_2$ $O_3$ films were prepared by two different method via sol -Eel process. Tetraethylorthosilicate(TEOS)/aluminum secondary butoxide [Al (OC$_4$ $H_{9}$)$_3$], methacryloxypropylcnethoxysaane(MPTS)/aluminum secondary butofde [Al(OC$_4$ $H_{9}$)$_3$] systems were used as starting materials for hosting Er ions. Er-doped $SiO_2$-A1$_2$ $O_3$ films obtahed after heat-treating, coatings on Si substrate were characterized by X-ray din action, FT-IR, and N-IR fluorescence spectroscopy. The luminescence properties for two different processing procedure will be compared and discussed from peak intensity and life time.

• Journal of Sensor Science and Technology
• /
• v.10 no.3
• /
• pp.156-162
• /
• 2001

Novel pressure sensor using the resonance wavelength shift of single mode fiber-to-planar waveguide coupler, was demonstrated. It is found that the resonance wavelength shift due to refractive index variation of polymers by pressure occurs and its sensitivity depends on materials. We adopted symmetric structure of planar waveguide and remove the polarization dependence which is inevitable with side-polished fiber. AZ4562, AZl512 and THB-30 are used as planar waveguide materials and the resonance wavelength shifting by pressure was shown -0.008um/bar, 0.033nm/bar and 0.16nm/bar, respectively.

• The Korean Journal of Physiology and Pharmacology
• /
• v.13 no.1
• /
• pp.39-47
• /
• 2009

Gaegurin 4(GGN 4), an antimicrobial peptide isolated from a Korean frog, is five times more potent against Gram-positive than Gram-negative bacteria, but has little hemolytic activity. To understand the mechanism of such cell selectivity, we examined GGN4-induced $K^+$ efflux from target cells, and membrane conductances in planar lipid bilayers. The $K^+$ efflux from Gram-positive M. luteus(2.5 ${\mu}g/ml$) was faster and larger than that from Gram-negative E. coli(75 ${\mu}g/ml$), while that from RBC was negligible even at higher concentration(100 ${\mu}g/ml$). GGN4 induced larger conductances in the planar bilayers which were formed with lipids extracted from Gram-positive B. subtilis than in those from E. coli(p<0.01), however, the effects of GGN4 were not selective in the bilayers formed with lipids from E. coli and red blood cells. Addition of an acidic phospholipid, phosphatidylserine to planar bilayers increased the GGN4-induced membrane conductance(p<0.05), but addition of phosphatidylcholine or cholesterol reduced it(p<0.05). Transmission electron microscopy revealed that GGN4 induced pore-like damages in M. luteus and dis-layering damages on the outer wall of E. coli. Taken together, the present results indicate that the selectivity of GGN4 toward Gram-positive over Gram-negative bacteria is due to negative surface charges, and interaction of GGN4 with outer walls. The selectivity toward bacteria over RBC is due to the presence of phosphatidylcholine and cholesterol, and the trans-bilayer lipid asymmetry in RBC. The results suggest that design of selective antimicrobial peptides should be based on the composition and topology of membrane lipids in the target cells.

• Korean Journal of Optics and Photonics
• /
• v.15 no.2
• /
• pp.109-113
• /
• 2004

We have manufactured and characterized the fiber-to-Planar Waveguide Coupler for analysis of the photo-induced refractive index change of DM-BTE .(l,2-bis[2,5-dimethylthio-phen-3-yl]-hexafluorocyclopentene) When irradiated with ultraviolet light, the colorless diarylethene(DM-BTE)-crystal turned red while keeping the crystal shape. The red color was bleached by irradiation with visible light(λ＞450 nm). The resonant wavelength was shifted and recovered owing to the refractive index variation of the planar waveguide because of its photo-functional properties on exposure to UV and visible light. The wavelength responses of this switch by UV exposure were measured as 0.057 nm/sec with saturation time of 60 seconds. and when illuminated by visible light, resonance wavelength variations were measured as 0.028 nm/sec, with recovery time of 140 seconds.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.7
• /
• pp.42-49
• /
• 1999

In this paper, we proposed a simple measurement method to find the behaviors of the fiber-to-waveguide coupler. The polished fiber blocks and planar waveguides on silicon dioxide were fabricated independently and then optically coupled by physical pressure. Several kinds of polymer with different refractive indices were used for waveguide films. The proposed method makes it possible to measure the center wavelength, bandwidth, extinction ratio, and polarization dependence of the coupler during fabrication procedure. The wavelength sensitivity increased with refractive index of polymer. The symmetric planar waveguide structure and isotropic property of guiding materials reduced polarization dependent property. Insertion loss of the coupler was less than 0.5dB. It is expected that our measurement method is useful for developing various optical devices using evanescent coupling between polished fiber and planar waveguide such as optical modulators and filters etc.

• Transactions of the Korean hydrogen and new energy society
• /
• v.20 no.4
• /
• pp.300-308
• /
• 2009

In a pursuit of the development of alternative mobile power sources with a high energy density, a planar and air-breathing PEMFCs with a new type of hydrogen cartridge which uses onsite $H_2$ generated from sodium borohydride ($NaBH_4$) hydrolysis have been investigated for use in advanced power systems. Two types of $H_2$ generation through $NaBH_4$ hydrolysis are available: (1) using organic acids such as sulphuric acid, malic acid, and sodium hydrogen carbonate in aqueous solution with solid $NaBH_4$ and (2) using solid selected catalysts such as Pt, Ru, CoB into the stabilized alkaline $NaBH_4$ solution. It might therefore be relevant at this stage to evaluate the relative competitiveness of the two methods mentioned above. The effects of flow rate of stabilized $NaBH_4$ solution, MEA (Membrane Electrode Assembly) improvement, and type and flow control of the catalytic acidic solution have been studied and the cell performances of the planar, air-breathing PEMFCs using $NaBH_4$ has been measured from aspects of power density, fuel efficiency, energy density, and fast response of cell. In our experiments, planar, air-breathing PEMFCs using $NaBH_4$ achieved to maximum power density of 128mW/$cm^2$ at 0.7V and energy efficiency of 46% and has many advantages such as low operating temperature, sustained operation at a high power density, compactness, the potential for low cost and volume, long stack life, fast star-up and suitability for discontinuous operation.

• Journal of the Korean Magnetics Society
• /
• v.12 no.3
• /
• pp.109-116
• /
• 2002

We designed the flyback planar transformer, which had 8 W capacity, with 70 V input voltage and 8.2 V output voltage for the establishment of design method and the confirmation of application possibility. The numerical value of inductance measured under the switching frequency of 120 kHz was 1650 $\mu$H, which was the inductance efficiency of'85∼87% against theoretical value. The A.C. resistance of primary and secondary coil was 4.2 Ω and 0.25 Ω respectively, On the other hand, the quality factor for each wound numbers showed quite a high value of 158 and 75 respectively. And the Coupling Factor was 0.96∼0.97 under 120 kHz switching frequency. The inductance rapidly increased as the thickness of the core plane increased until it became 1.4 mm but under the thickness more than 1.4 mm, there was no substantial change. Therefore, the critical value of the plane thickness of core was 1.4 mm. And the shape of the output wave of the planar transformer at 70V input voltage was a stable square wave.

• Korean Journal of Optics and Photonics
• /
• v.15 no.6
• /
• pp.490-494
• /
• 2004

Bragg gratings were fabricated in Ge-doped silica planar lightwave circuits (PLC) for different writing conditions to study the growth characteristics. The refractive index modulation of the gratings grew in the PLC with total fluence F according to the power law $\Delta$n=A $F^{B}$. The characteristics of the PLC gratings formed for external cavity lasers match closely to those predicted by the power law. The oscillation spectra of the FP-LD with a Bragg grating grown in the PLC waveguide were also presented.d.

• Korean Journal of Optics and Photonics
• /
• v.7 no.1
• /
• pp.51-59
• /
• 1996

In this paper, we propose a new type of a planar waveguide lens, a meniscus lens instead of a plano-convex lens used widely for the optical integrated circuits such as optical numerical processors. A plano-convex lens has a spherical aberration caused by the linear boundary. In the proposed meniscus lens, this linear boundary is replaced by a circular-boundary, and the spherical aberration is removed. To test the performance of the proposed lens, a meniscus lens is designed using Fermat principle and fabricated on the Y-cut $LiNbO_3$ substrate. First a $Ti:LiNbO_3$ planar waveguide is fabricated on the $LiNbO_3$ substrate by Ti indiffusion. Then a meniscus lens is fabricated on the planar waveguide by TIPE(Ti indiffued proton-exchange) method. A plano-convex lens is also fabricated on the same substrate to compare the spot size at the focal point. The measured spot size of the meniscus lens is reduced to 59% that of the plano-convex lens. This result shows that the proposed meniscus lens is more effective for optical integrated circuits than the plano-convex lens.

• Journal of architectural history
• /
• v.19 no.5
• /
• pp.7-23
• /
• 2010

The aim of this study is to analyze the planar composition of rectangular formation houses in 8 areas, both cities and counties, in the sphere of Andong and to reveal the characteristics of these houses in each region. This study of the rectangular formation of houses and their characteristics will facilitate an understanding of the general trends of housing in Andong cultural area.. In this study, the subject houses are composed of three parts: Bonchae, Anchae, and Sarangchae, and the author classified the planar types of the houses. The differences in the regional planar types were analyzed through visual and statistical methods. The analyzed results reveal the regional characteristics of the rectangular formation houses in terms of their planar aspects in the Andong region. The distribution showed the greatest preference toward one type out of two types of distribution of Bonchae, Anchae, and Sarangchae. The ratio for the higher distribution was approximately 70%, whereas the ratio for the lower distribution was around 20%. For convenience, the type with a higher distribution rate is referred to as the "major type," and the type with a lower distribution rate is termed the "minor type." The complete-type houses (73%) in Bonchae were a major type there, and the symmetric-type houses (73%) in Anchae were the major type in that location. In addition, the corner-type houses (72%) in Sarangchae were the major type. In the regional distribution of major types and minor types in the 8 regional cities and counties, regional differences were noted. The three regional groups can be divided into A, B, and C according to the distribution ratio. Andong, Bonghwa, and Yecheon belong to region A. that shows a variety of distribution types and a dispersive trend. Yeongyang and Yeongdeok belong to region C that shows a simplified trend.Yeongju and Cheongsong belong to region B.