• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.7
• /
• pp.72-76
• /
• 2008

In this paper, the several printed square loop antennas which modified monopole antennas are proposed. The proposed antennas are reduced about 20% physical size of antenna and miniaturized reactance value of impedance due to fold center part of the loop. They obtained omni-directional radiation patterns with broad bandwidth and feed method used coplanar waveguide to composed single planar. The proposed antenna bandwidth is about 900MHz($2.63{\sim}3.56GHz]$) resonance frequency on $VSWR{\le}2$. it can be sufficiency of S-DMB band.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.05a
• /
• pp.45-46
• /
• 2014

In this paper, measurement methods for the characteristics of antennas for indoor digital TV (DTV), having 75-ohm port impedance, are introduced. Reference impedance of typical radio frequency (or microwave) systems and measurement equipments is 50 ohm. However, the reference impedance of antennas for indoor DTV is 75 ohm, and the characteristics of the antennas cannot be measured directly using the measurement equipments. Measurement methods, using test equipments with reference impedance of 50 ohm, for the characteristics(impedance, radiation patterns, and gains) of antennas designed to fit for 75 ohm port are introduced.

• Steel and Composite Structures
• /
• v.49 no.2
• /
• pp.181-196
• /
• 2023

Marine structures including offshore wind turbines (OWTs) always work under cyclic loads, which arouses much attention on the fatigue design. The tripod substructure is one of the typical foundation forms for fixed OWTs. The three-planar tubular Y-joint (3Y joint) is one of the important components in fatigue design as it is most likely to have cracks. With the existence of the multiplanar interaction effect, calculating the hot spot stress (HSS) of 3Y joints is complicated. To assist with fatigue design, the distributions of stress concentration factor (SCF) and multiplanar interaction factor (MIF) along weld toe curves induced by the out-of-plane bending moment are explored in this study. An FE analysis method was first developed and verified against experimental results. This method was applied to build a numerical database including 1920 FE models covering common ranges of geometric parameters. A parametric study has been carried out to reveal the distribution patterns of SCF and MIF. After multidimensional nonlinear fittings, SCF and MIF distribution formulas have been proposed. Accuracy and reliability checking prove that the proposed formulas are suitable for calculating the HSS of 3Y joints.

• Journal of IKEEE
• /
• v.12 no.4
• /
• pp.185-195
• /
• 2008

In this paper, PIFA(Planar Inverted F Antenna) which operates in PCS(Personal Communication System) band is designed and characteristics are investigated. Designed PIFA was installed in three types of handsets, folder, bar, slide, and the performance was evaluated. Head and hand phantom were added to make the most similar environment to real condition of mobile phone use, and influences on antenna performance were analyzed. The simulation results confirm radiation patterns are greatly changed and antenna efficiency is decreased by the effect of human body. Performance variation of the mobile handset antenna was observed as changing the angle between mobile handset and head phantom from $0^{\circ}$ to $2^{\circ},\;4^{\circ}$ to confirm the variation caused by the relative position of mobile handset and head phantom. Directivity was decreased gradually as the antenna goes away from head phantom, and showed the trend of increasing efficiency. But in the case of bar type, where the position of antenna is relatively close to head phantom, that trend didn't show. It was confirmed that the shape of handset has a great effect on the performance.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.4
• /
• pp.25-29
• /
• 2015

Demand for a low-cost, high-throughput, and high-resolution patterning method for fabricating devices continues to increase. The roll-to-roll (R2R) imprint lithography technique has received a great deal of attention as a means of fabricating next-generation devices. In this paper, we propose a fabrication method for polymeric planar lightwave circuit (PLC) devices that uses R2R imprint lithography. The proposed technique uses an elastomeric polydimethylsiloxane (PDMS) mold. A Si wafer with micro patterns is used as the Si master. The PDMS mold is then replicated from the Si master. By applying a precise web tension and at a given web speed, we fabricated a micro-patterned PLC device. The insertion losses were 4.0 dB for a $1{\times}2$ optical splitter. As such, the proposed method of fabricating a PLC device by the R2R process was shown to be an effective solution.

• Journal of Advanced Navigation Technology
• /
• v.24 no.3
• /
• pp.232-237
• /
• 2020

In this paper, a compact microstrip-fed dual-band planar antenna for global positioning system (GPS) and mobile handset applications is presented. Dual operating frequency bands are achieved by an open end L-shaped slot and a bent rectangular slot. The proposed antenna is designed and fabricated on the FR4 substrate with dielectric constant of 4.3, thickness of 1.6 mm and size of 57 × 57 ㎟. The measured impedance bandwidth (|S₁₁|≤ -10dB) of the fabricated antenna is 60 MHz(1550 ~ 1610 MHz) in the GPS band and 670 MHz (1690 ~ 2360 MHz) in the DCS / IMT-2000 band, covering the required bandwidths for GPS(1570 ~ 1580 MHz) and DCS / IMT-2000 (1710 ~ 2200 MHz) bands. In particular, it has been observed that antenna has a good omnidirectional radiation patterns as well as high gain of 2.36 dBi and its efficiency is more than 90 % over the entire frequency band of interest.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.12 s.103
• /
• pp.1194-1205
• /
• 2005

This paper proposes a uni-planar elliptical element UWB antenna with band-notched characteristic and modified pound plane fed by CPW. The antenna achieves VSWR below 2 for UWB band(3.1 GHz${\~}$10.6 GHz). In addition, a band-notched characteristic is achieved by inserting a horizontal slot on the radiation element to avoid the interference with 5 GHz(5.15 GHz${\~}$5.825 GHz) band limited by IEEE 802.1la. The antenna has a thin profile, compact size, and ease of manufacture by adopting a CPW feed structure without any additional background plane. Measured data show that the proposed antenna has good return loss below -10 dB, about 2.1 dB${\~}$4.75 dB maximum gain over the bandwidth, omni-directional radiation patterns, linear phase response.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.15 no.6
• /
• pp.812-819
• /
• 2012

Interference and jamming are becoming increasing concern to a radar system nowdays. AESA(Active Electronically Steered Array) antennas and adaptive beamforming(ABF), in which antenna beam patterns can be modified to reject the interference, offer a potential solution to overcome the problems encountered. In this paper, we've developed a planar active phased array radar system, in which ABF, target detection and tracking algorithm operate in real-time. For the high output power and the low noise figure of the antenna, we've designed the S-band TRMs based on GaN HEMT. For real-time processing, we've used wavelenth division multiplexing technique on fiber optic communication which enables rapid data communication between the antenna and the signal processor. Also, we've implemented the HW and SW architecture of Real-time Signal Processor(RSP) for adaptive beamforming that uses SMI(Sample Matrix Inversion) technique based on MVDR(Minimum Variance Distortionless Response). The performance of this radar system has been verified by near-field and far-field tests.

• Fire Science and Engineering
• /
• v.26 no.2
• /
• pp.11-16
• /
• 2012

In this paper, we analyzed damage patterns of a folder type mobile phone caused by microwave-irradiation, to find an accurate fire cause and to investigate deliberate broken of mobile phone for obtaining pecuniary advantage by deception. In order to analyze broken patterns, we irradiated a mobile phone with microwave using by 2.45 GHz microwave oven. Form the experiment results, damage patterns of mobile phone have been tendency toward heavy broken patterns depending on time of microwave-irradiated. Distinctively, folder hinge and intenna(Planar Inverted-F Antenna) were heavy broken in compare with battery, enclosure and so on. The enclosure of mobile phone became just thermo-metamorphism and the battery was not broken such as explosion.

• ETRI Journal
• /
• v.35 no.1
• /
• pp.51-57
• /
• 2013

In this paper, a small internal antenna for a mobile handset is presented using multiband, wideband, and high-isolation multiple-input multiple-output techniques. The proposed antenna consists of three planar inverted-F antennas (PIFAs) that operate in the global system for mobile communication (GSM900), the digital communication system (DCS), the personal communication system (PCS), the universal mobile telecommunication system (UMTS), and wireless local area network (WLAN) bands with a physical size of $40mm{\times}10mm{\times}10mm$. A resonator attached to the folded PIFA creates dual resonances, achieving a wide bandwidth of approximately 460 MHz, covering the DCS, PCS, and UMTS bands; a meander shorting line is used to improve impedance matching. Additionally, a modified neutralization link is embedded between diversity antennas to enhance isolation, which results in a 6-dB improvement in the isolation and less than 0.1 in the envelope correlation coefficient evaluated from the far-field radiation patterns. Simulation and measurements demonstrate very similar results for S-parameters and radiation patterns. Peak gains show 3.73 dBi, 3.77 dBi, 3.28 dBi, 2.15 dBi, and 5.86 dBi, and antenna efficiencies show 56.15%, 72.15%, 68.59%, 52.92%, and 82.93% for GSM900, DCS, PCS, UMTS, and WLAN bands, respectively.