• Korean Journal of Applied Biomechanics
• /
• 제30권1호
• /
• pp.1-6
• /
• 2020

Objective: The incidence rate of elbow ulnar collateral ligament injuries is dependent on the throwing speed or pitching type, especially in adolescent baseball players. However, mixed results have been reported due to a lack of controlled biomechanical analysis. Thus, the purpose of this study was to investigate the biomechanical analysis of the elbow in relation to throwing speed and pitching type. Method: Four overhead type high-school baseball players were recruited for this study. The participants were asked to throw balls with different types of pitch and speed. While the throwing speeds were measured, each pitching moment of the elbow was recorded. Descriptive statistics, frequency analysis, mean comparison analysis, and Pearson's correlation analysis were performed in order to examine differences in peak varus and valgus moment during pitching motion in the elbow in all throwing speed and pitching types. Results: There was no significant difference in physical characteristics, throwing speed, and momentum variability among all players. The mean varus moments were 44.38±1.55 Nm, 48.83±1.66 Nm, and 48.94±0.95 Nm, and the moment gaps between varus and valgus were 7.36±3.25 Nm, 7.44±2.02 Nm, and 7.36±2.62 Nm in fastball, curveball, and slider ball, respectively. The varus moment was higher in the curved and slider balls than in the fastballs, and there was no significant differences between the varus moments regarding the pitching type. However, the increase in valgus moment and decrease in moment gap according to throwing speed was significantly increased in the slider ball (r=0.718 and -0.591, respectively). Conclusion: The possibility of elbow injury caused by the valgus moment or moment gapincreases more rapidly in slider balls as the speed increases. Based on our results, appropriate pitching guidelines should be suggested to prevent ulnarligament injuries, especially in adolescent baseball players.

• Smart Media Journal
• /
• 제13권4호
• /
• pp.16-22
• /
• 2024

Pitching is a major part of baseball, so much so that it can be said to be the beginning of baseball. Analysis of accurate pitching motions is very important in terms of performance improvement and injury prevention. When analyzing the correct pitching motion, the currently used motion capture method has several critical environmental drawbacks. In this paper, we propose analysis of pitching motion using the RGB-based Human Pose Estimation (HPE) model to replace motion capture, which has these shortcomings, and use motion capture data and HPE data to verify its reliability. The similarity of the two data was verified by comparing joint coordinates using the Dynamic Time Warping (DTW) algorithm.

• Transactions of the Korean Society of Automotive Engineers
• /
• 제3권5호
• /
• pp.100-110
• /
• 1995

The human subject perception response according to vertical vibration and pitching was analyzed with a five degree of freedom model. The vehicle dynamic system with the delayed colored noise excitation and the passenger perception response was arranged as an integrated viration system and could be analyzed simultaneously for seven different combination of vehicle suspension. ISO2631 and BS6841 was adapted for analyzing the passenger perception reponse. Simulation results shows that passenger feel relatively less discomfort due to pitching compared to vertical vibration and road type was not necessary to be considered as a design parameter in view of comfort analysis.

• Transactions of the Korean Society of Automotive Engineers
• /
• 제6권3호
• /
• pp.154-160
• /
• 1998

Ride quality of medium truck became a very important factor in the suspension design, to the demand of more comfortable ride of passengers. This study describes how to determine and evaluate design parameters related to the chassis suspension system with time and frequency analysis. The spring stiffness and damping force of the chassis suspension system were obtained by observing the vertical acceleration PSD. The simulation was carried out on various road profiles, which was suggested by ISO. The pitching motion of the medium size truck was observed to improve the ride quality. A computer simulated truck model was constructed using DADS, a commercial dynamic analysis software, in order to simulate the truck motions. From the analyzed process of suspension parameters, it was concluded that the spring and the shock absorbers affect the pitching of the vehicle. In order to validate the computer simulated truck model, a physical prototype was constructed and tested.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• 제64권12호
• /
• pp.1695-1702
• /
• 2015

This paper presents the characteristic analysis and experiment of force characteristics in permanent magnet linear synchronous motor for accuracy prediction of linear motion machine tools. In particular, the pitching moment resulting from attraction force ripple has been analysed and tested. Firstly, we analysed the characteristics of detent force, attraction force, and pitching moment in permanent magnet linear synchronous motor according to the design techniques such as auxiliary teeth, chamfering, and permanent magnet skewing. In addition, we suggested the experimental set for measurement of pitching moment. Finally, the results from measurement shows the good agreement with those obtained from finite element analysis results.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• 제29권2호
• /
• pp.39-48
• /
• 2023

Background: The position of pitcher requires a lot of repetitive motion, and because of this, it is known that not only professional baseball players, but also middle and high school players are frequently exposed to injuries in baseball. The purpose of this study is to examine the differences in upper extremity muscle activity during repeated pitching and the activity of each muscle during repeated pitching by analyzing middle and high school pitchers, divided into groups by age. Methods: Twenty participants (10 middle school male students and 10 high school male students) were recruited for this research. The outcome measures included neuromuscular motor control, including the upper trapezius (UT), triceps brachii (TB), deltoid (DT), latissimus dorsi (LD), biceps brachii (BB), pectoralis major(PM), extensor carpi radialis(ER), and flexor carpi radialis (FR). Results: The two-way analysis of varaince (ANOVA) was used to compare the muscle activity variables between the middle school and high school students. The one-way ANOVA was used to compare the muscle activity variables within time differences each groups. Conclusion: Our results provided promising clinical evidence that guide for upper extremity muscles to increase pitching efficiency in middle and high school base ball players.

• Korean Journal of Applied Biomechanics
• /
• 제12권2호
• /
• pp.109-130
• /
• 2002

The purpose of this paper was to make a comparative analysis for the difference of the various kinematic variation which is occurred in the each situation when pitchers throw a straight and a curve ball. Four pitchers, who are two national team players and two high level pitchers, were selected among the right over hand pitchers of D university in the Busan for this paper. The data were analyzed by using 3D equipment. The results of the analysis which was about the elapsed time of the pitching, the movement of the body center-point, the highest height of the left knee, stride length, knee joint angle, shoulder joint angle, elbow joint angle and wrist joint angle in the each section(ST, LKU, HBP, LCF, MCP, BRP) were as follows : 1. Pitching time in the each section and step in the pitching for straight and curve ball was similar. The total elapsed time of the straight and curve ball was 1.78${\pm}$0.07sec and 1.77${\pm}$0.11sec in the order. 2. The position change of the body center to the Z(above below) direction did not show significant difference in the each situation of the section and step between pitching for the straight and curve ball. 3. Height of the left knee did not show significant difference as 125.38${\pm}$11.85cm and 124.95${\pm}$11.63m in the each pitching motion for straight and curve ball. The rate(%H) between height and stride length showed 68.42${\pm}$5.53(%H), 68.40${\pm}$5.45(%H) in the each pitching motion. 4. Pitching for curve ball showed longer stride length than pitching for straight ball that as the stride length was 140.35${\pm}$4.96cm and 144.8${\pm}$1.69cm. The rate(%H) between height and stride length showed 76.9${\pm}$3.77(%H), 79.39${\pm}$2.23(%H) in the each pitching motion. 5. Left knee joint angle did not show significant difference in the ST, LKU and HBP section in the each pitching motion. However, it was shown that knee joint angle was flexed much more in the LFC, MCP and BRP section in the pitching for curve ball. 6. Right shoulder joint angle did not show significant difference in the ST, LKU and HSP section. However, when pitches threw a curve ball in the LKU section. In the LFC section, the right shoulder joint angle was extended much more in the pitching for curve ball, and the angle was extended much in the MCP and BRP section in the pitching for curve ball than straight ball. 7. Right elbow joint angle did not show significant difference in the ST, LKU and HRP section in the two pitching motion. The angle had more flexion in the LFC and MCP section in the pitching for curve ball than the pitching for straight ball. The angle in the each pitching motion for straight ball and curve ball were extended by a narrow margin in the BRP section. 8. Right wrist joint angle was extended much more in the LFC and MCP section in the pitching for curve ball. In the BRP section, the angle was extended much more in the pitching for straight ball than curve ball.

• Journal of the Korean Society of Mechanical Technology
• /
• 제13권2호
• /
• pp.71-78
• /
• 2011

A kart is a vehicle without the suspension system and the differential gear. The kart frame as an elastic body plays the role of a spring. By the cornering of a kart, rolling, pitching and twisting motions are induced in the kart frame. Also the slip or noncontact of the wheel and a permanent deformation of the kart frame can be induced. In order to examine closely this phenomenon, measurement on height-displacements with various sensors and tracking system and analysis on the kart frame twisting characteristics with the rolling and pitching angle are needed. According to the measurement result, while driving in a curve at high speed the kart frame is quite twisted. Analysis on the measurement results shows that a kart used primarily in high speed requires a frame with low torsional stiffness and a frame material with high tensile strength and large elongation.

• Journal of computational fluids engineering
• /
• 제16권1호
• /
• pp.53-59
• /
• 2011

In this study, steady and unsteady aerodynamic analyses of a huge rocket configuration have been conducted in a transonic flow region. The launch vehicle structural response are coupled with the transonic flow state transitions at the nose of the payload fairing. Before performing the coupled fluid-structure transonic aeroealstic simulations transonic aerodynamic characteristics are investigated for the pitching motions of the rocket at finite angle-of-attack. An unsteady CFD analysis method with a moving grid technique based on the Reynolds-averaged Navier-Stokes equations with the k-w SST transition turbulence model is applied to accurately predict the transonic loads of the rocket at pitching motion. It is shown that the fluctuating amplitude of the lateral aerodynamic loads imposed on the rocket due to the pitching motion can be significantly increased in the transonic flow region.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.924-929
• /
• 2001

The flying height of contact slider is determined by vertical and pitching motions of slider. This paper performed the computer simulation for flying height change of contact slider. It is changed by many parameters, contact stiffness, contact damping, air bearing stiffness ratio, a location of mass center, and so on. Computer simulation is performed for knowing for what change of these parameters influences in flying height of contact slider. Disk surface is modeled in harmonic wave with from 10㎑ to 600㎑. Tri-pad slider is modeled in that contact slider has 2-DOF motion (vertical motion, pitching motion). Tri-pad contact slider is analyzed by numerical analysis method in computer simulation.