• Journal of Power System Engineering
• /
• v.10 no.4
• /
• pp.56-64
• /
• 2006

This paper shows the development process of a straight-type five-hole pressure probe for measuring three-dimensional flow velocity components. The data reduction method using a bi-cubic curve-fitting program in a new calibration map was introduced in this study. This new calibration map can be applied up to the application angle, ${\pm}55^{\circ}$ of a probe. As a result, for the application angle of ${\pm}45^{\circ}$, an error for yaw and pitch angles appeared from $-1.76^{\circ}\;to\;1.83^{\circ}$ and from $-1.91^{\circ}\;to\;1.75^{\circ}$, respectively. Moreover, an error for a vector magnitude and a static pressure compared with a dynamic one showed from -7.83% to 4.87% and from -0.73 to 0.77, respectively. Even though this data reduction method showed unsatisfactory errors in a vector magnitude, it resulted in an easy and simple application method. Especially, when it was applied to an actual flow field including a swirling flow, a good result came out on the whole. However, in order to obtain a better result, it is thought that a more sophisticated interpolation method needs to be introduced.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.10
• /
• pp.891-898
• /
• 2007

Optimal aerodynamic design for the pitch-controlled horizontal axis wind turbine and its aerodynamic performance for various pitch angles are performed numerically by using the blade element momentum theory. The numerical calculation includes effects such as Prandtl‘s tip loss, airfoil distribution, and wake rotation. Six different airfoils are distributed along the blade span, and the special airfoil i.e. airfoil of 40% thickness ratio is adopted at the hub side to have structural integrity. The nonlinear chord obtained from the optimal design procedure is linearized to decrease the weight and to increase the productivity with very little change of the aerodynamic performance. From the comparisons of the power, thrust, and torque coefficients with corresponding values of different pitch angles, the aerodynamic performance shows delicate changes for just $3^{\circ}$ increase or decrease of the pitch angle. For precisive pitch control, it requires the pitch control algorithm and its drive mechanism below $3^{\circ}$ increment of pitch angle. The maximum torque is generated when the speed ratio is smaller than the designed one.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.8
• /
• pp.784-790
• /
• 2012

This paper describes a stability and dynamic characteristics of bearingless helicopter main rotor in hover. Baseline rotor configuration is defined and modal analysis for the configuration is taken to verify the dynamic characteristics. The kinematic pitch-lag couplings through ways of pitch link installation are analyzed to know effects on loads, frequencies and stability. The effects of pitch link attachments in spanwise direction and chordwise direction as well as pitch link inclination on thrust, power, flpa-lag-pitch mode frequencies and inplane damping are examined. Pitch link at trailing edge location in chordwise direction has influence on aeroelastic stability of the rotor. Also, the pitch link with negative inclination angle makes inplane damping increase.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.394-399
• /
• 2012

This paper describes a stability and dynamic characteristics of bearingless helicopter main rotor in hover. Baseline rotor configuration is defined and modal analysis for the configuration is taken to verify the dynamic characteristics. The kinematic pitch-lag couplings through ways of pitch link installation are analyzed to know effects on loads, frequencies and stability. The effects of pitch link attachments in spanwise direction and chordwise direction as well as pitch link inclination on thrust, power, flpa-lag-pitch mode frequencies and inplane damping are examined. Pitch link at trailing edge location in chordwise direction has influence on aeroelastic stability of the rotor. Also, the pitch link with negative inclination angle makes inplane damping increase.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.4
• /
• pp.84-91
• /
• 2003

The paper presents a power control algorithm for a full pitch-controlled wind power system. The design of a pitch controller, in general, is performed by linearizing the torque in the vicinity of a operating point assuming the tip speed ratio is constant. For power control, however, the tip speed ratio is no longer a constant. In this study, a reference pitch model is derived in terms of a wind speed, angular velocity, and pitch angle. The reference pitch model is used to design a controller without linearizing the non-linear torque model of the blade. The validity of the algorithm is demonstrated with the results produced through sets of simulation.

• Wind and Structures
• /
• v.35 no.2
• /
• pp.121-130
• /
• 2022

In this paper, the issue of pitch control in a vertical axis wind turbine was tackled. Programming the Actuator Cylinder model in MATLAB, a theoretical optimum pitch solution was found and then a classic four-bar mechanism was adapted to that theoretical solution to achieve a simple and elegant control of the pitch in the turbine. A simulation using the mechanism worked to find the optimum pitch cycles, where it was found that the mechanism would, in fact, increase the efficiency of the VAWT, by at least 11% and in the best case, over 35%. Another aspect that is studied is the possibility of self-start of the turbine by only changing the pitch on the blades. This analysis, however, proved that a further individual pitch control must be used to surpass the cogging torque. All analyses conducted were done for a specific wind turbine that is 2 m² in the swept area.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.221-224
• /
• 2003

In the open die forging process, it is difficult to optimize process parameters such as die shape, initial ingot size, feeding pitch, rotation angle and other process parameters in the operational environments. Therefore in this study, 3D finite element analysis has been performed to obtain optimal process condition for open die forging process. FEM analyses at various feeding pitches and rotation angles provide process conditions to make round bar having precise dimensional accuracy.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.355-360
• /
• 1991

A method of autopilot gain-scheduling is presented for missiles which have heavy aerodynamic coupling between pitch and yaw channels due to high maneuverability. Pitch and yaw, autopilot are cross-coupled, and their feedback gains are scheduled by total acceleration and bank angle for given Mach number and height. Bank angle information is obtained by using a simple estimator. By computer simulation, it is shown that the proposed method is superior to other existing methods.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.861-866
• /
• 1996

The Non-Circular Gears is more advantage than other machinery using link and cam in the automation equipment. We designed Non-Circular Gears for a velocity of inequalty rotational equipment according to the variation of pressure angle, radius of curvature etc., and studied about pitch curve.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04b
• /
• pp.17-19
• /
• 2008

본 연구에서는 우리나라와 같은 낮은 풍속에서 사용 가능한 블레이드의 형태와 블레이드의 피치각이 풍력터빈의 효율에 미치는 영향을 확인하고자 블레이드를 2종류의 형태로 제작하여 블레이드의 피치각에 따른 출력특성을 측정 하였다. 풍력터빈의 효율은 블레이드의 형태와 피치각에 대해 출력이 크게 좌우되었으며, 낮은 풍속 상태에서는 공기의 힘을 받는 면적이 클수록 출력특성이 좋게 나타났다.