• Proceedings of the KIEE Conference
• /
• 2004.11b
• /
• pp.17-20
• /
• 2004

This paper presents a modeling and simulation of a grid-connected wind turbine generation system with respect to wind variations and three-phase fault in the system. It describes the modeling of the wind turbine system including the drive train model, induction generator model, and grid-interface model on MATLAB/Simulink. Case studies demonstrate that the pitch angle control is carried out to achieve maximum power extraction for wind speed variations and the duration of a fault on the system influences on the output of the wind turbine generator.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.237-242
• /
• 2000

The areal recording density of HDD(Hard Disk Drive) has been increasing by about 60% a year. In order to achieve high areal density, less track pitch is expected and more servo bandwidth is required. Dual stage actuator and servo controller for HDD have been suggested for achieving high track density as a possible solution. Dual-loop servo system is generally classified into a two-input-two-output system, but if we use an estimator for a two-input-two-output system, it can be converted into two input one output system. Since we can't control the dual stage servo system by the classical method, it requires a special technique; for example, Parallel Loop System, Master-Slave Loop System, Decoupled Master-Slave Loop System, and Dual Feedback Loop System. In this paper, we performed experimental evaluations of several types of control algorithm. Further experiments will be made in the future.

• Journal of Biosystems Engineering
• /
• v.33 no.6
• /
• pp.371-378
• /
• 2008

Bio-diesel applications seem to be extended due to bio-diesel policies and changes of agricultural environment. This study was conducted to develop a rapeseed reaping equipment attachable to the conventional combine. This paper was intended to report concept design, process and manufacturing of the prototype rapeseed reaping equipment. For concept design, physical properties of "SUNMANG", which is a typical rapeseed as bio-diesel materials, were considered. The designed prototype rapeseed reaping equipment consisted of wide-width plates, finger type knifes, side cutter knifes and drive equipments. The wide-width plate is 2.1 m wide, 0.7 m long, and 0.002 m thick. The finger type cutter knifes have 14.5 fingers, 30 knifes, and the specification was 7.6 cm of pitch, 8.3 cm of length and $21^{\circ}$ of cutting angle. The side cutter knifes consisted of a hydraulic pump, a hydraulic motor, a flow control and a relief valve, a hydraulic hose, a driving equipment and a reciprocating cutter knife. The 18 reciprocating cutter knifes were 137 cm long and knife pitch, knife length and cutting angle were 7.7 cm, 10.5 cm, and $18^{\circ}$. Prototype weight of the rapeseed reaping equipment was heavier by 272 kg when compared with the manual reaping equipments. Load distributions of left and right side showed 50% and 49%, and those of front and rear side showed 64% and 36%. Static turn-over angles in left and right of the prototype were $38.1^{\circ}$ and $38.7^{\circ}$, respectively. The designed prototype rapeseed reaping equipment was properly mounted at the front of a conventional combine.

• The Bulletin of The Korean Astronomical Society
• /
• v.38 no.2
• /
• pp.39.1-39.1
• /
• 2013

We use high-resolution hydrodynamic simulations to study nonlinear gas responses to imposed non-axisymmetric stellar potentials in barred-spiral galaxies. The gas is assumed to be infinitesimally thin, isothermal, and unmagnetized. We consider various spiral-arm models with differing strength and pattern speed, while fixing the bar parameters. We find that the extent and shapes of spiral shocks as well as the related mass drift depend rather sensitively on the pattern speed. In models where the arm pattern is rotating more slowly than the bar, the gaseous arms extend from the bar ends all the way to the outer boundary, with a pitch angle slightly smaller than that of the stellar counterpart. The arms drive mass inflows at a rate of ${\sim}0.5-2.5M{\odot}/yr$ to the bar region to which the shock dissipation, external torque, and self-gravitational torque contribute about 50%, 40%, and 10%, respectively. About 85% of the inflowing mass is added to bar substructures such as an inner ring, dust lanes, and a nuclear ring. while the remaining 15% encircles the bar region. On the other hand, models where the arms corotate with the bar exhibit mass outflows, rather than inflows, over most of the arm region. In these models, spiral shocks are much more tightly wound than the stellar arms and cease to exist in the region where $M{\bot}/sinp*{\geq}25-40$, where $M{\bot}$ denotes the Mach number of a rotating gas perpendicular to the arms with pitch angle p*. We demonstrate that the distributions of line-of-sight velocities and densities can be a useful diagnostic tool to distinguish if the arms and bar corotate or not.

• Journal of Biosystems Engineering
• /
• v.34 no.5
• /
• pp.315-324
• /
• 2009

Various types of vibration are transmitted to operators of agricultural tractors while working in the field. Most harmful vibration to human body is ride vibrations with low frequency ranging from 1 to 10 Hz, caused by rough terrain. These ride vibration has vertical and rotational components. This study was conducted to develop an active seat suspension system with two degrees of freedoms, enabling effectively reduce vibrations in vertical and pitch motions. Therefore, a mechanism for the active seat suspension was developed, and an electro-hydraulic servo system and a controller to drive the active seat suspension system were also developed in this study. A simulation model was developed to evaluate how the active seat suspension system effectively reduce the vibrations transmitted to the base of seat. Active seat suspension was optimized to enhance the performance using the developed simulation model. The performance of the seat suspension system was evaluated according to the test codes described in EEC78/764 in order to investigate the feasibility of application to agricultural tractors. The result showed that the developed active seat suspension system could reduce the magnitude of vertical vibration up to 80% for the input vibrations according to the test codes described in EEC78/764. The system could reduce the rotational displacement of ${\pm}\;2.5$ degrees up to 50% for the pitch vibration on the average in the frequency range of 1 to 2 Hz.

• Journal of the Society of Naval Architects of Korea
• /
• v.35 no.3
• /
• pp.26-37
• /
• 1998

In this study, the motion control techniques allied to the test ship NARAE are summarized and the results of sea trials are resented. NARAE adopted a hybrid hull form with lower hull and submerged foils. This type of ship has a substantial instability in heave, pitch and roll modes at the foil-borne stage due to little restoring force, so an active control is indispensable to keep the stability. 4-hydraulic actuators with servo valves were installed to drive foils, and several sensors were used to measure the motion of the ship. PID controller was adopted as a motion controller, and for the real-time control, Pentium-class industrial PC was used. Sea trials including take-off, landing, and banked turn maneuvering were carried out for a period of over 3 months and quite satisfactory results were obtained.

• Journal of IKEEE
• /
• v.26 no.4
• /
• pp.602-613
• /
• 2022

This paper proposes an algorithm for correcting indirect situations resulting from the wheelchair moving the stairs with wheel-type caterpillar and seat position variable. For analyzing the Yawing movement model, the change of Yaw value was estimated using Roll, Pitch, and Yaw in the driving environment, and it was used as a control variable and the information of the wheel drive controller. The verification confirmed the correction of about 10° of Yawing movement within about 7 seconds. It was confirmed that the angular velocity was reduced by 47.5% in seat position change.

• International Journal of Precision Engineering and Manufacturing
• /
• v.2 no.2
• /
• pp.65-72
• /
• 2001

The design of multi-stage gear drives is a time-consuming process, since on includes more complicated problems, which are not considered in the design of single-stage gear drives. The designer has th determine the number of reduction stages and the gear ratios of each reduction state. In addition, the design problems include not only the dimensional design but also the configuration design of gear drive elements. There is no definite rule and principle for these types of design problems. Thus the design practices largely depend on the sense and the experiences of the designer , and consequently result in undesirable design solution. We propose a new generalized design algorithm to support the designer at the preliminary design phase of multi-stage gear drives. The proposed design algorithm automates the design process by integrating the dimensional design and the configuration design process. The algorithm consists of four steps. In the first step, a designer determines the number of reduction stage. In the second step. gear ratios se chosen by using the random search method. In the third step, the values of basic design parameter are chosen by using the generate and test method. Then, the values of other dimension, such ad pitch diameter, outer diameter, and face width, are calculated for the configuration design in the final step. The strength and durability of a gear is guaranteed by the bending strength and the pitting resistance rating practices by using the AGMA rating formulas. In the final step, the configuration design is carried out b using the simulated annealing algorithm. The positions of gears and shafts are determined to minimize the geometrical volume(size) of a gearbox, while satisfying spatial constraints between them. These steps are carried out iteratively until a desirable solution is acquired. The propose design algorithm has been applied to the preliminary design of four-stage gear drives in order to validate the availability. The design solution have shown considerably good results in both aspects of the dimensional and the configuration design.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.12
• /
• pp.965-971
• /
• 2003

To reach high areal density, less track pitch is expected and more servo bandwidth is required. One approach to overcoming the problem is by using dual stage servo system. For this system. we have suggested new milliactuator based on the shear mode of piezoelectric elements to drive the head suspension assembly. In this paper, we introduce milliactuator and controller design method, PQ method. PQ method reduces the controller design problem for DISO (dual-input/single-output) systems to two standard controller design problems for SISO ( single-input/single-output) problems. The first part of PQ method directly addresses the issue of actuator output contribution, and the second part allows the use of traditional loop shaping to achieve the overall system performance. This paper shows how to employ the PQ method to meet aggressive close-loop performance specifications for a disk drive system with a VCM and piezoelectric milliactuator.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.8
• /
• pp.1545-1551
• /
• 2002

The optical storage device has recently experienced significant improvement, especially for the aspects of high capacity and fast transfer rate. However, it is necessary to study a new shape of air bearing surface for the rotary type actuator because the optical storage device has the lower access time than that of HDD (Hard Disk Drives). In this study, we proposed the air bearing shape by using SA (Simulated Annealing) algorithm which is very effective to achieve the global optimum instead of many local optimums. The objective of optimization is to minimize the deviation in flying height from a target value 100nm. In addition, the pitch and roll angle should be maintained within the operation limits.