• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.2
• /
• pp.195-202
• /
• 2016

In general, piston pumps are frequently used for concrete pumping. Filling coefficient signifies the ratio volume of a hydraulic cylinder to volume of concrete inside the cylinder. Therefore, it may be considered as a parameter directly affecting the flow rate and efficiency for concrete pumping. However, accurate analyses on this aspect have not yet been performed. In this paper, the data measured from horizontal pipeline pumping tests for 350m and 548m in length was analyzed to identify the relationships of rheological properties of concrete and stroke time with the filling coefficient. In addition, an equation allowing prediction of the filling coefficient from rheological properties of concrete and stroke time has been suggested.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.102-109
• /
• 2017

The high pressure pump of a diesel injection system compresses the fuel supplied at low pressure into high pressure fuel and maintains the fuel of the common rail at the required pressure level according to the engine operating conditions. The high pressure pump is required to operate normally in order to compress the fuel to a high pressure of 2000 bar during the entire lifetime of the vehicle. Consequently, a suitable design technique, material durability and high precision machining are required. In this study, the high pressure pump simulation model of a 1-plunger radial piston pump is modelled by using the AMESim code. The main simulation parameters are the displacement, flow rate and pressure characteristics of the inlet and outlet valves, cam torque characteristics, and operating characteristics of the fuel metering valve and overflow valve. In addition, the operating characteristics of the pump are simulated according to the parameter changes of the hole diameter and the spring initial force of the inlet valve. The simulation results show that the operation of the developed pump model is logically valid. This paper also proposes a simulation model that can be used for current pump design changes and new pump designs.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.17 no.2
• /
• pp.3763-3771
• /
• 1975

This study was attempted to investigate the changes of specific fuel consumption, compression pressure and power output, consequently to obtain basic data on farm kerosene engine. The samples which are used in this study are a 4 cycle water cooled korosene engine for the use of K6-CT83 power tiller and a 4 cycle air-cooled kerosene engine for the use of G5L-3A water pump. The Korean Industrial Standards (K.S)KS-B 6002 "Test code of small internal combustion engine" was referred in carrying out this study, and its results are as follows. 1. According to load increasing, the speific fuel consumption of the engines generally decreases, however, in case of 10% over-loading it increases. 2. As a result of full load consecutive operation, according to passing of operating time, the amount of wear generally increases, consequently the speific fuel consumption also increases, and inversly the compression pressure decreases. 3. The changes of specific fuel consumption and compression pressure were closely related with time of piston ring exchange, and periodically about 100 hours the engines show the increase of specific fuel consumption and the decrease of compression pressure. 4. After about 300 hours, although the engine had new piston rings, the specific fuel consumption increase, consequently the engine needs boring. In actual use, it is impossible to operate consecutively on full load, therefore the boring time of engine is expected to come later.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.5
• /
• pp.39-44
• /
• 2009

The hydrostatic slipper bearing is generally used in high pressure axial piston pumps to support the load generated from two surfaces which are sliding relatively at low speed. The object of the bearing is to remove the possibility of direct contact by maintenance of an adequate oil film thickness between two metal surfaces. Because the bearing performance is influenced by the bearing deformation, it is highly dependent on the injection pressure, the bearing surface profile and so on. In this study, the deformation characteristics of a hydrostatic slipper bearing is investigated according to the injection pressure by the finite element analysis. In the analysis, the special boundary condition to take the fluid-structure interaction (FSI) into account is used on the interactive surface. The results, such as bearing deformation, stress and lifting force, obtained from the fully coupled analysis are compared with those from the single step sequential method.

• Journal of Drive and Control
• /
• v.16 no.3
• /
• pp.23-32
• /
• 2019

This study proposed a fault tolerant control algorithm for electro-hydraulic brake systems where permanent magnet synchronous motor (PMSM) drive is adopted to boost the braking pressure. To cope with motor position sensor faults in the PMSM drive, a braking pressure controller based on an open-loop speed control method for the PMSM was proposed. The magnitude of the current vector was determined from the target braking pressure, and motor rotational speed was derived from the pressure control error to build up the braking pressure. The position offset of the pump piston resulting from a leak in the hydraulic system is also compensated for using the open-loop speed control by moving the piston backward until it is blocked at the end of stroke position. The performance and stability of the proposed controller were experimentally verified. According to the results, the control algorithm can be utilized as an effective means of degraded control for electro-hydraulic brake systems in the case that a motor position sensor fault occurs.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.6
• /
• pp.687-692
• /
• 2016

When turbochargers are applied to engines, the temperature of the engine becomes high, making the cooling of pistons very important. To solve this problem, an oil jet is used. The oil jet provides oil to the underside of piston for cooling. When an oil jet is used, oil pump size-up and oil cooler are needed because of the increased oil flow rate and higher oil temperature. On the other hand, these increase the friction torque of the engine. This study examined how much the friction torque of an engine increases by an oil jet, oil cooler, and oil pump size-up. In addition, the proportions of the friction torque of the engine increased by each part were measured by changing the engine assembly condition. At low speed, the oil pump and oil cooler had a larger effect on the friction torque than the other factors. At high speed, oil cooler had a larger effect than the other factors.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.711-714
• /
• 2008

The objective of this paper is to know the characteristics of pressure through a simplified typical carburetor used in small engines at the different throttle opening conditions. The carburetor is the device responsible for creating the right air-fuel mixture according to the different engine operating conditions. It is activated by the static or the dynamic pressure. The carburetor dummy is geometrically similar of LPG brush-cutter engine's diaphragm carburetor and is made of acrylic. Suction system gives body to crankcase vacuum using the vacuum pump and throttle opening conditions are controled by transfer device. Carburetor venturi throat and fuel charging tube diameter is each 20mm, 4.1mm. The result of the work presents an unprecedented phenomenon of suction pressure variation inside the carburetor venturi. It is predicted that these unprecedented pressure variation be caused by minor losses; sudden contraction or expansion, open or partially closed and so on.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.5
• /
• pp.91-96
• /
• 2006

The friction and wear properties of ceramics are very important in the applications to engineering ceramic parts such as seal rings, pump parts, automobile meter parts, and so on. In this study, the effects of each other purity on the mechanical and tribological properties of purity zirconia ceramics were investigated. Also in order to determine the effects of sliding distance, sliding speed, contact load, friction coefficient, the amount of worn out material at a certain time, and the prepared composites were measured. Crystalline phases and microstructure were examined with XRD and SEM. The results show that we obtained the good properties of friction coefficient and wear resistance at the purity 99.5% of zirconia. than this of the purity 95% were great at the wear amount of worn out material.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.03a
• /
• pp.281-286
• /
• 1998

In this paper, a Helmholtz resonator type hydraulic filter is proposed to absorb flow and pressure ripple produced from a axial piston pump. The basic principle of hydraulic filter is applied to propagation of preossure waves, reflection, absorption in cross section of discontinuity and resonance in the pipeline. This filter has advantage of the compact size and high degree of freedom of installation. The design scheme of hydraulic filter based on viscous wave theory are developed and manufactured two kinds of filter to investigate damping capability. It is experimently confirmed that these filter is absorbed to be about 20dB of flow and pressure ripple with high frequencies.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.185-188
• /
• 2008

In this study, we experimentally investigated that the optimization of pulsating jet to reduce the separated flow region behind the vertical fence. The vertical fence was submerged in the turbulent boundary layer in the circulating water channel and we applied phase averaged PIV method to measure the instantaneous velocity fields around the fence. One cycle of pulsating jet is divided into 20 phases and grabbed total 200 instantaneous velocity fields at each phase. The experiments were performed by varying the frequency, maximum jet velocity and the shape of pulsating jet wave. Pulsating jet was precisely made by piston-type pump controlled by the computer. The obtained results were compared with normal fence flow. From this study, we found there is the specific frequency which is effective in reducing the reattachment region.