• 대한기계학회논문집A
• /
• 제24권12호
• /
• pp.2935-2944
• /
• 2000

Gas tungsten arc(GTA) welding is used to rrpiar the seat ring in swing type check valve in power plant because of its high weld quality. In order to automate the welding process, it is needed to analyze the process of inside pipe girth welding. In this study, the shapes of weld bead on pipe inside and outside were predicted and its validity was investigated. On the assumption that the welding arc had a bivariate gaussian distribution, analytical solution was derived to predict the temperature distribution in pipe weld using mapping under consideration of physical relationships. The size of weld bean could be predicted from this equation and its accuracy was verified by experiments.

• Journal of Welding and Joining
• /
• 제33권1호
• /
• pp.54-60
• /
• 2015

Laser-arc hybrid welding has been considered as an effective pipe girth welding process since early 2000's. Tolerance for fit-up offsets such as gap and edge misalignment is one of most important requirements in pipe girth laser-arc hybrid welding, and several approaches using parameter optimization, a laser beam scanning and an arc oscillation have been tried. However the required offset tolerance has not been fully accomplished up to now and laser-arc hybrid welding has not been widely applied in pipeline construction than expected, despite of its high welding speed and deep penetration. In this study, internal welding was adopted to ensure the offset tolerance and sound back bead. The effect of welding parameters on bead shape was investigated at the flat position. Also tolerances for gap and edge misalignment were verified as 0.5 mm and 2.0 mm, respectively. The position welding trials were conducted at several welding positions from the flat to the overhead position in a downward direction. With the fixed welding speed, arc current for gas metal arc welding current and laser output power, adequate welding voltages for gas metal arc welding were suggested for each position.

• Journal of Welding and Joining
• /
• 제27권6호
• /
• pp.25-30
• /
• 2009

SBD (Strain-based design) of pipe lines have gained world-wide attention in recent years. The present research aims to evaluate the fracture characteristics of API (America Petroleum Institute) SBD X100 girth weldment that typically applied for cold climate and deep water offshore, with the focus on the influence of heat input changing with 6kJ/cm and 10kJ/cm from GMAW (Gas Metal Arc Welding). At a low heat input at 6kJ/cm, the weld metal had Multi-phase matrix (Acicular ferrite + Banite + Martensite) that could fill up both fracture toughness and strength as reported previously. Also, the weld metal exhibited 859MPa YS (Yield strength), 108J impact toughness at $-40^{\circ}C$ and 0.52mm CTOD (Crack Tip Open Displacement) at $-10^{\circ}C$. These results can be satisfied with the requirement of API SBD X100 girth weldment and Alaska pipe line project.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2010년도 춘계학술발표대회 초록집
• /
• pp.71-71
• /
• 2010

SBD (Strain-based design) of pipe lines have gained world-wide attention in recent years. The present research aims to evaluate the fracture characteristics of API (America Petroleum Institute) SBD X100 girth weldment that typically applied for cold climate and deep water offshore, with the focus on the influence of heat input changing with 6kJ/cm and 10kJ/cm from GMAW (Gas Metal Arc Welding). At a low heat input at 6kJ/cm, the weld metal had Multi-phase matrix (Acicular ferrite + Banite + Martensite) that could fill up both fracture toughness and strength as reported previously. Also, the weld metal exhibited 859MPa YS (Yield strength), 108J impact toughness at $-40^{\circ}C$ and 0.52mm CTOD (Crack Tip Open Displacement) at $-10^{\circ}C$. These results can be satisfied with the requirement of API SBD X100 girth weldment and Alaska pipe line project.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.222-227
• /
• 2001

This paper introduces the spring-mounted odometer system which maintains the correct contact with the pipe wall and measures the distance along the pipe. The odometer wheel is designed to keep contact to the pipelines inner wall and to generate fifty rectangular pulses per one turn(l59.5681mm) during pigging. The pipeline has the defects in various types such as buckles, winkles, cracks, dents, welding point and so on. Specially, girth welding points which exist each 12m of the pipeline, much affects the operational environment of the odometer. The measurement error of the distance along the pipe is accumulated, for the measurement error of wheel's circumference and the pipeline inner environment. So, this paper proposes the method for the error compensation based on the analysis of the odometer's behavior around the girth welding point of pipe. The experimental results show that developed odometer system can be used for the intelligent pig with good performances.

• 한국가스학회지
• /
• 제6권1호
• /
• pp.17-23
• /
• 2002

피깅에서 얻어진 정보들 중에서 피그의 주행거리가 가장 기본이 되는 정보이며, 정확한 이동거리의 측정이 반드시 필요하게 된다. 배관은 일반적으로 buckles, winkles, cracks, dents, welding feints좌 같은 결함을 지니게 되는데, 이들 결함 주위에서는 주행거리계의 거동이 변화하게 된다. 특히 가장 높은 빈도로 나타나게 되는 결함은 배관의 12m마다 존재하는 welding points로서, 주행거리 측정오차 발생의 주요한 원인이 된다. 본 연구에서는 산업 현장에 실제로 적용할 수 있는 주행거리계의 개발뿐만이 아니라 welding points에서 변화하는 주행거리계의 거동을 해석하고, 발생하는 측정오차를 보정하였다. 또한 실험을 통해서 주행 속도에 따른 오차가 인정된 성능 범위내로 보정됨을 확인하였고. 그 유용성을 검증하였다.

• 한국재난정보학회 논문집
• /
• 제11권1호
• /
• pp.1-8
• /
• 2015

본 연구에서는 토압 등의 외압이 원주 용접된 매설 강관의 잔류응력에 미치는 영향을 유한요소 해석을 통하여 명확히 하였다. 먼저 3차원 열탄소성 해석을 통하여 원주 용접된 강관의 잔류응력을 구하였으며, 이를 초기조건으로 설정하여 3차원 탄소성 해석을 수행함으로써 외압이 작용하는 경우 잔류응력 거동을 조사하였다. 해석결과 외압에 의해 원주 용접부에 발생하는 원주방향 압축응력 때문에 원주방향 잔류응력이 압축 측으로 상당히 많이 이동함을 알 수 있었고, 축방향 잔류응력은 작용하는 외압에 의해 거의 영향을 받지 않음을 알 수 있었다.

• Journal of Welding and Joining
• /
• 제35권1호
• /
• pp.55-60
• /
• 2017

There are many Industry Code and Standard (ICS) for Structural Integrity Assessment (SIA) on welded structure with defect. The general ICSs, such as R6, BS 7910 and API 579-1/ASME FFS-1, provide equations to determine the upper bound residual stress profiles based on collections from many literatures. However, these residual stress profiles used in the SIA cause the conservative design for welded structures. In this study, the structural integrity assessment for girth weld in pipeline has been conducted based on fracture mechanics. In addition, thermo-elastic plastic FE analysis was performed for evaluating the residual stress of girth weld in pipeline. The weight function solution is used to determine the stress intensity factor using the residual stress profile obtained by the FE analysis. This approach can account for redistribution and relaxation of residual stress as the defects grow. In order to the evaluate quantitative comparison between BS 7910 and weight function solution, structural integrity assessment determining allowable crack size on cracked pipe was performed with failure assessment diagram.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 추계학술발표대회 개요집
• /
• pp.165-167
• /
• 2004

The failure pressure for corroded pipeline was measured by burst testing and classified with respect to corrosion sizes and corroded regions - the body, the girth weld and the seam weld of pipe. A series of finite element analyses were performed to obtain a limit load solution for corrosion defects on the basis of burst test. As a result, the criteria for failure assessment of corrosion defect within the body, the girth weld and the seam weld of API 5L X65 gas pipeline were proposed.

• Nuclear Engineering and Technology
• /
• 제54권11호
• /
• pp.4072-4083
• /
• 2022

Ultrasonic impact treatment (UIT) is carried out on the Ni-based alloy stainless steel pipe gas tungsten arc welding (GTAW) girth weld, the differences of microstructure, microhardness and shear strength distribution of the joint before and after ultrasonic shock are studied by microhardness test and shear punch test. The results show that after UIT, the plastic deformation layer is formed on the outside surface of the Ni-based alloy overlayer, single-phase austenite and γ type precipitates are formed in the overlayer, and a large number of columnar crystals are formed on the bottom side of the overlayer. The average microhardness of the overlayer increased from 221 H V to 254 H V by 14.9%, the shear strength increased from 696 MPa to 882 MPa with an increase of 26.7% and the transverse average residual stress decreased from 102.71 MPa (tensile stress) to -18.33 MPa (compressive stress), the longitudinal average residual stress decreased from 114.87 MPa (tensile stress) to -84.64 MPa (compressive stress). The fracture surface has been appeared obvious shear lip marks and a few dimples. The element migrates at the fusion boundary between the Ni-based alloy overlayer and the austenitic stainless steel joint, which is leaded to form a local martensite zone and appear hot cracks. The welded joint is cooled by FA solidification mode, which is forming a large number of late and skeleton ferrite phase with an average microhardness of 190 H V and no obvious change in shear strength. The base metal is all austenitic phase with an average microhardness of 206 H V and shear strength of 696 MPa.