• 한국정밀공학회지
• /
• 제19권7호
• /
• pp.163-170
• /
• 2002

This paper presents some measures far the optimization of the thermal behavior of linear motors, which are used as a high speed feed mechanism in machine tools. Thermo-Sandwich-Construction using two cooling circuits and an insulation layer shows an effective cooling system for linear motors. Conducting sheet can be also used to reduce heat flow from linear motor to machine table. Cooling pipe is a simple and effective cooling system for the secondary part of synchronous linear motor. Through the combination of the Thermo-Sandwich-Construction, conducting sheet and cooling pipe the thermally optimized linear motor shows a well improved thermal behavior in comparison with the prototype motor.

• 한국기계가공학회지
• /
• 제21권3호
• /
• pp.110-117
• /
• 2022

A chiller cooler absorbs the thermal energy of water to generate cold water and supplies the generated cold water to a cold water pipe buried in the wall of a small mobile modular house to greatly increase the cooling area. An attempt was made to reduce the required cooling time significantly. A small chiller cooler suitable for the cooling load of a small mobile modular house with an area less than 3.3 m² was employed. When cooling is done during summer using a chiller cooler installed outdoors, heat absorption energy loss occurs in the cold water pipe owing to the high temperature. To address this, a study was conducted to reduce the endothermic energy loss significantly. As the mass flow rate of the cold water flowing inside the cold water pipe increased, the temperature decrease gradient of the cold water increased. From the start of the cooling operation, the air temperature of the small mobile modular house decreased linearly in proportion to the operation time. Furthermore, the temperature of the air inside the small mobile modular house decreased in proportion to the increase in the flow of water inside the cold water pipe.

• 설비공학논문집
• /
• 제16권8호
• /
• pp.741-747
• /
• 2004

The purpose of this study was to develop a cooler/heater using a thermoelectric module combined with a parallel flow type oscillating heat pipe with R-142b as a work ing fluid. The experiment was performed for 16 thermoelectric modules (6 A/15 V, size: 40${\times}$40${\times}$4 mm), varying design parameters of the heat pipe (inclination angle, working fluid charging ratio, etc) . Experimental results indicate that the optimum charging ratio and the inclination angle of the parallel flow type oscillating heat pipe were 30% by volume and 30%, respectively. The maximum cooler/heater capacity were 479W (COP : 0.47) and 630W (COP : 0.9), respectively.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제13권4호
• /
• pp.217-224
• /
• 2005

The purpose of this study was to develop a cooler/heater using a thermoelectric module combined with a parallel flow type pulsating heat pipe with R-142b as a working fluid. The experiment was performed for 16 thermoelectric modules (6A/15V, size: $40\times40\times4mm$), varying design parameters of the heat pipe (inclination angle, working fluid charging ratio, etc.). Experimental results indicate that the optimum charging ratio and the inclination angle of the parallel flow type pulsating heat pipe were $30\%$ by volume and $30^{\circ}$, respectively. The maximum cooler/heater capacity were 479 W (COP: 0.47) and 630 W (COP: 0.9), respectively.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.867-868
• /
• 2010

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권1호
• /
• pp.30-36
• /
• 2010

다중관식 헬리컬 코일형 가스냉각기내 $CO_2$의 열유량과 압력강하에 대해서 실험적으로 조사하였다. $CO_2$와 냉각수의 유량은 각각 0.06~0.075kg/s이고, 가스냉각기의 냉각압력은 8~10 MPa이다. $CO_2$의 열유량은 냉각수 질량유량, $CO_2$의 질량유량과 냉각압력에 비례하여 증가한다. $CO_2$의 압력강하는 냉각수와 $CO_2$의 질량유량이 감소할수록 감소하지만, $CO_2$의 냉각압력이 증가할수록 감소한다. 다중관식 헬리컬 코일형 가스냉각기내 $CO_2$의 열유량과 압력강하는 각각 이중관식 가스냉각기보다 상당히 높게 또는 낮게 나타났다. 따라서 다중관식 헬리컬 코일형 가스냉각기에 $CO_2$를 적용하는 경우에는 가스냉각기의 고효율화, 고성능화, 컴팩트화가 가능할 것이다.

• 방사성폐기물학회지
• /
• 제5권3호
• /
• pp.213-220
• /
• 2007

유리화공정 고온영역에서의 방사성 배기체 유동해석을 해석하기 위하여 상용 수치해석 범용 툴인 FLUENT를 이용하여 적용성을 검토하여 보았다. 수치해석을 통하여 유리화공정 원형설비에 영향을 미치는 인자를 파악하였는데, 저온용응로, 배관냉각기 및 고온필터 등의 세 단계로 나누어 해석을 수행하였다. 저온용융로의 경우 폐기물 처리용량에 따른 해석과 저온용융로 내부 과잉산소 공급 비에 따른 연소지연 가능성에 대한 수치해석을 수행하였다. 배관냉각기의 경우에는 각종 수치 모델 및 외벽 열전달계수를 확보하였으며 또한 방사성 핵종의 거동을 모사할 수 있는 수치적 기업을 검토하였다. 이러한 방법론을 적용하여 핵종의 열교환기 내부에서의 응고 특성에 대하여 고찰하였다. 수평 유입형식의 인입관이 있는 일반적인 형상과 유입구가 필터 내부에 수직으로 있는 고온필터의 수치해석을 통하여 인입관의 위치에 따른 고온필터의 작동 특성을 비교하였다.

• 교육시설 논문지
• /
• 제18권3호
• /
• pp.35-41
• /
• 2011

Performance of a small-capacity solar absorption cooling system was investigated experimentally. Ten sets of evacuative-tube solar-heat collectors and a 5 kW single-stage absorption cooler were combined to produce a hybrid cooling system. The performance of the cooling system was measured using a tim-coil unit installed in a small plastic storage. It was found from the test on a sunny day of May that when the temperature of the hot water supplied from the solar collectors to the generator of the absorption cooler reached $60^{\circ}C$, the absorption cooler started cooling and the cold water temperature measured from the fan-coil unit reached $18^{\circ}C$. The COP, which is defined as the ratio of the cooling power to the total electrical power input was higher than 1.0.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.216-221
• /
• 2005

The heat transfer coefficient and pressure drop during gas cooling process of carbon dioxide in a helically coiled tube were investigated experimentally. The experiments were conducted without oil in the refrigerant loop. The main components of the refrigerant loop are a receiver, a variable speed pump, a mass flowmeter, a pre-heater, a gas cooler(test section) and an isothermal tank. The test section is a double pipe type heat exchanger with refrigerant flowing in the inner tube and water flowing in the annulus. It was made of a copper tube with the inner diameter of 4.85 [mm], the outer diameter of 6.35 [mm] and length of 10000 [mm]. The refrigerant mass fluxes were 200${\sim}$600 [kg/$m^2$s] and the average pressure varied from 7.5 [MPa] to 10.0 [MPa]. The main results were summarized as follows: The heat transfer coefficient of supercritical $CO_2$ increases, as the cooling pressure of gas cooler decreases. And the heat transfer coefficient increases with the increase of the refrigerant mass flux. The pressure drop decreases in increase of the gas cooler pressure and increases with increase the refrigerant mass flux.

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2005년도 추계 학술대회 논문집
• /
• pp.69-78
• /
• 2005

유리화공정 고온영역에서의 방사성 배기체 유동해석을 통하여 해석에 적합한 모델을 개발하였다. 개발된 모델을 이용한 수치해석을 통하며 유리화공정 원형설비에 영향을 미치는 인자를 파악하였는데, 저온용융로. 배관냉각기 및 고온필터 등의 세 단계로 나누어 해석을 수행하였다. 저온용융로의 경우 폐기물 처리용량에 따른 해석과 저온용융로 내부 과잉산소 공급 비에 따른 연소지연 가능성에 대한 수치해석을 수행하였다. 배관냉각기의 경우에는 각종 수치 모델 및 외벽 열전달계수를 확보하였으며 또한 방사성 핵종의 거동을 모사할 수 있는 수치적 모델을 개발하였다. 이러한 방법론을 적용하여 핵종의 열교환기 내부에서의 응고 특성에 대하여 고찰하였다. 수평 유입형식의 인입관이 있는 일반적인 형상과 유입구가 필터 내부에 수직으로 있는 고온필터의 수치해석을 통하여 인입관의 위치에 따른 고온필터의 작동 특성을 비교하였다.