• Journal of ILASS-Korea
• /
• v.3 no.1
• /
• pp.34-42
• /
• 1998

The correlation between the droplets size and the velocity are investigated for an intermittent spray of the pintle type fuel injector employed in a port injection gasoline engine. The analysis such as the mean droplet size, SMD, and velocity under the fixed injection period and varied fuel pressures are conducted utilizing PDPA systems. As results, the experimental data obtained, show that the larger droplet sizes. the higher velocities during the spray tip arrival time, and that at Z=70mm, r=8mm, both droplet sizes and velocities are peak. At the upstream, flow of droplets are dominated by injection pressure, which are more effected inertia force of droplets at the downstream of Z=70mm.

• Journal of ILASS-Korea
• /
• v.4 no.4
• /
• pp.9-16
• /
• 1999

Spray angle, a parameter which is most commonly used to evaluate. spray distribution, is important because it affects the axial and radial distribution of the fuel. Spray angles were measured and compared for the pintle-type gasoline fuel injector with n-heptane as a test fuel with the three different measuring techniques, i.e. digital image processing, shadowgraphy and spray patternator, respectively. Fuel was injected with the injection pressures of 0.2-0.35MPa into the room temperature and atmospheric pressure environment. In digital image processing method, the transmittance level greatly influences the spray angle with the axial distance from the injector. From the experimental results by the shadowgraphy technique, it is obvious that the spray angle vary during the injection period. The results of spray angle from the spray patternator show that there exist the different spray angles in the different areas. The spray angles increase with the increase in the injection pressure for the three measurement techniques considered in this study. The spray angle is widely different, especially in the near region from the injector, according to the measurement techniques used in this experimental work.

• Journal of ILASS-Korea
• /
• v.3 no.3
• /
• pp.42-48
• /
• 1998

This study describes the spray structure of gasoline port injectors by using phase Doppler particle analyzer(PDPA) and particle motion analysis system(PMAS). The characteristics of fuel spray such as the spray penetration, spray angle and breakup processes were obtained by PMAS and the droplet size and mean velocity were measured by PDPA system. Pintle type and two-hole type injectors were used as gasoline port fuel injectors under various injection pressures. The effect of injection pressure on the droplet mean diameter and axial mean velocity of droplet were investigated under the various injection conditions. In addition the comparison of breakup processes for the two types of injectors was also conducted. It Is shown that pintle type injector has smaller droplet size than that of two-hole type injector.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.405-409
• /
• 2010

금속분말을 청정 에너지원으로 이용하기 위해 금속분말 소형 연소기의 구현이 필요하다. 이를 위한 선행연구로 연료 공급 시스템인 핀틀인젝터형(pintle injector type) 금속분말 공급장치의 중요 성능인 분사량을 실험적으로 측정하였다. 분사량 측정 시험에 앞서 간단한 금속분말 공급 시험으로 확인된 문제점을 장치의 변경을 통해 해결하였다. 측정 시험의 결과, 연료 공급 장치에 이송 가스 압력이 상승함에 따라 많은 질유량의 금속분말이 분사되었고 압력에 따른 정량적 분사량을 확인하였다. 이송 가스와 금속분말의 혼합 성능을 개선하여 균일한 분사를 하고자 이송 가스를 25 Hz로 가진 하여 공급하였고 가진이 없는 경우의 실험결과와 비교하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.9
• /
• pp.1198-1206
• /
• 1997

The flow characteristics of an intermittent fuel injection into a stationary ambient air were investigated using gasoline. The measurements were made by two-channel, air cooling type Phase Doppler Anemometer(PDA) system (DANTEC, 750 MW). And a pintle type injector of MPI (Multi-point Port Injection) system was utilized as a fuel injector. The PDA receiver optic was set up in a 60.deg. C forward scatter arrangement to obtain the optimum scattering signal of fuel droplets. The data were obtained by synchronizing PDA system with the fuel injection period, and the axial and radial velocity and turbulent components of fuel droplets were mainly measured for the analysis of temporal and spatial distribution depending upon the fuel injection pressures.

• Journal of ILASS-Korea
• /
• v.3 no.2
• /
• pp.24-33
• /
• 1998

The characteristics of liquefied butane spray are expected to be different from conventional diesel fuel spray, because a kind of flash boiling spray is expected when the back pressure is below the saturation vapor pressure of the butane(0.23MPa at $25^{\circ}C$). An accumulator type pintle injector and its fuel delivery system has been simulated in ruder to give injection pressure, needle lift and rate of fuel injected. The governing equation were solved by finite difference metho. The injection duration was controlled by solenoid valve. Spray behaviors such as a transient spray tip penetration, spray angle and SMD were calculated based on the empirical correlations in case that the back pressure is both above the vapor pressure of the butane and below that of butane. When the back preassure is below the vapor pressure of the fuel, conventional correlation is modified to represent the effect of flash boiling.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.3
• /
• pp.187-197
• /
• 1998

To investigate the spray behavior and atomization characteristics using an air-assist injector, spray visualization and PDPA measurements were carried out under the various assisted air pressures and the fixed fuel pressure. The air assist pintle type injector employed in this study is consisted of the air assist adaptor and an injector housing using the gasoline fuel and air as the working fluids. As results, increasing pressure of assisted air, the growth of spray tip penetration is gradually reduced at the end of spray and spray angle is steadily increased at the main spray region except from the early spray. For the air assist pressure of 25㎪ in a spray downstream, it is doncluded that droplet size distribution shows the peak of 10${\mu}{\textrm}{m}$ and most of the droplet sizes are less than 50${\mu}{\textrm}{m}$. Also, the air-assist injector extremely improves fuel atomization in order to produce much finer droplets, it shows that approximately, in this case, 50% decreade of SMD than without air assit.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.6
• /
• pp.134-144
• /
• 1995

The solenoid actuated hydrogen injector and the capacitive peak-hold type driving circuit were designed and made, and the hydrogen supply system for in-cylinder injection was constructed with these. The performance of the injector was investigated through measuring the pintle lift profiles and the injection quantities, and the performance of the hydrogen supply system was confirmed through the experiments at the single cylinder engine. The injection quantity increased linearly as the duration of driving signal increased. At the single cylinder engine, the hydrogen injector was operated stably. The hydrogen flow rate of the injector with the peak-hold type driving circuit could be controlled precisely at high engine speed or low load condition only with the variation of signal duration.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.4
• /
• pp.112-120
• /
• 2001

Poor fuel vaporization in gasoline engines causes the problem of HC emission during the cold start and warm-up period. This paper presents a strategy to improve fuel atomization during the warm-up phase. In this experiment, the heated fuel-rail system is constructed to investigate the effects of fuel heating on the average size of fuel droplets. The fuel atomization effects are examined by measuring Sauter Mean Diameter (SMD) of the fuel droplets from the three different types (two-hole, pintle, and six-hole) of injectors based upon a returnless heated fuel-rail system. The results show that the six-hole type injector is the most sensitive to fuel heating in terms of SMD among three different types of injectors.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.219-227
• /
• 1998

This paper describes the fuel spray characteristics of gasoline port injectors such as the breakup procedures of liquid fuel, breakup and extinction behaviors of fuel spray at nozzle tip, time history of SMD and velocity distribution of fuel spray in the direction of fuel stream. Pintle-type gasoline fuel injector was used to analyze mentioned spray characteristics. In order to visualize the fuel spray behaviors and to measure the droplet mean diameter and velocities of spray droplets, the Schlieren method, digital image processing and auto-correlation PIV were applied in this study. In addition, the spray characteristics according to the variation of time were considered. The results of fuel spray show that the liquid sheet breakup starts at 10mm downstream actively. The flying time is approximately 4msec between 50mm and 80mm down the nozzle tip. Also, SMD of fuel spray, the number of droplets and fuel velocity distribution at each point of downstream are discussed.