• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.9-14
• /
• 2002

Ferrule is widely used as fiber optic connecters. In fiber-optic communications, the shape accuracy such as coaxiality and cylindricity of ferrule affects insertion loss. When coaxial grinding of ferrule supported by two pin, pin alignment and chucking accuracy are very important. In this research, the kinematic behavior of the ferrule center is investigated in the case where cone-shaped center pins and round circle hales which make contact with each other near the edge of the holes, using homeogenous coordinate transformation and numerical analysis. The obtained results are as follows: The alignment errors between center pins alone do not affect the rotation accuracy of ferrule. The alignment errors between center holes cause a sinusoidal displacement of ferrule. And the maximum displacement of ferrule centers increase in proportion to the center pin angle in the case of a fixed alignment errors

• Asian Pacific Journal of Cancer Prevention
• /
• v.14 no.10
• /
• pp.5965-5972
• /
• 2013

PIN1 is one member of the parvulin PPIase family. By controlling Pro-directed phosphorylation, PIN1 plays an important role in cell transformation and oncogenesis. There are many polymorphisms in the PIN1 gene, including rs2233678 and rs2233679 affecting the PIN1 promoter. Recently, a number of case-control studies were conducted to investigate the association between PIN1 gene rs2233678 and rs2233679 polymorphism and cancer risk. However, published data are still conflicting. In this paper, we summarized data for 5,427 cancer cases and 5,469 controls from 9 studies and attempted to assess the susceptibility of PIN1 gene polymorphism to cancers by a synthetic meta-analysis. Odds ratios (ORs) with 95% confidence intervals (CIs) were estimated to assess the relationship. All analyses were performed using Stata software. Our results suggested that rs2233678 represented a protective factor in overall analysis (CC vs GG: OR= 0.697, 95%CI: 0.498-0.976; CG vs GG: OR=0.701, 95%CI: 0.572-0.858; Dominant model: OR= 0.707, 95%CI: 0.590-0.847; C allele vs G allele: OR=0.734, 95%CI: 0.623-0.867) and especially for squamous cell carcinoma of the head and neck, lung cancer and breast cancer in Asians and Caucasians. The rs2233679 polymorphism was significantly associated with decreased cancer risk in overall analysis (CT vs CC: OR=0.893, 95%CI=0.812-0.981; Dominant model: OR=0.893, 95%CI=0.816-0.976; T allele vs C allele; OR=0.947, 95%CI=0.896-1.000) and especially in Asians. In conclusion, our meta-analysis suggested that -842G>C (rs2233678) and -667C>T (rs2233679) may contribute to genetic susceptibility for cancer risks. Further prospective research with larger numbers of worldwide participants is warranted to draw comprehensive and firm conclusions.

• Journal of Industrial Technology
• /
• v.27 no.B
• /
• pp.71-75
• /
• 2007

A cylindrical pin fin with variable diameter is analyzed by using the one dimensional analytical method. Heat loss and fin efficiency are presented as a function of the fin diameter, length and convection characteristic numbers ratio. The relationship between the fin diameter and convection characteristic number over the fin for the same amount of heat loss is shown. One of the results indicates the fin efficiency increases as the fin diameter increases while that decreases as the fin length increases.

• Journal of Industrial Technology
• /
• v.24 no.A
• /
• pp.9-15
• /
• 2004

The flexural strength from 3-point bend test and fatigue properties were measured to evaluate mechanical properties of metal/ceramic interface of the multilayer ceramic package produced through tape casting. From the results, the specimens with three electrode layers showed the highest strength. The temperature distribution with time during thermal cycle and thermal stresses with the change of electrode's shape have been estimated by mathematical modelling. Specimen affected by thermal shock, produced microcracks by the difference of thermal expansion coefficient. The results of tensile test and fatigue test showed the rupture at pin. The fact that the pin brazed specimens were always fractured at the pin proved the good bonding condition between pin and electrode.

• 한국정보통신설비학회:학술대회논문집
• /
• 2009.08a
• /
• pp.221-224
• /
• 2009

In this paper, we deal with the development of an optimal design program for a dual-band of 0.92 GHz and 2.45 GHz with shorting pin and slot by using evolution strategy. the optimal shorting pin, coaxial feed and H-shaped patch are determined by using an optimal design program based on the evolution strategy. To achieve this, an interface program between a commercial EM analysis tool and the optimal design program is constructed for implementing the evolution strategy technique that seeks a global optimum of the objective function through the iterative design process consisting of variation and reproduction. The resonance frequencies of the dual-band antenna yielded by the optimal design program are 0.92 GHz and 2.45 GHz that show a good agreement to the design target values.

• Clinics in Shoulder and Elbow
• /
• v.8 no.2
• /
• pp.105-109
• /
• 2005

Purpose: To Analyze the exit site of pin inserted at the anterior glenoid rim in the reconstruction of the Bankart lesion and SLAP lesion using transglenoid suture technique. Materials and Methods: In the twenty adult right cadeveric scapula, insertions of pin were performed using guide at the position of 1, 2, 3 O'clock of glenoid rim. We measured the exit site of dorsal surface of the scapula by medial distance from sagittal plane of lateral border of scapular spine and the vertical distance from posterior border of the scapular spine. Results: When the pin was inserted caudally within 10 degree, at the position of 1, 2, 3 O'clock, the medial distance from lateral border of the scapula is averaged 29.4, 19.2, 34.0 mm respectively and the vertical distance from posterior border of the scapular spine is averaged 15.0, 18.6, 17.2 mm respectively. When the pin was inserted caudally within 20-30 degree, the medial distance is averaged 14.6, 14.2, 15.8 mm respectively and the vertical distance is averaged 31.6, 31.9, 32.1 mm respectively. Conclusion: When the pin was inserted caudally within ten degrees using the guide, the pin exit appeared at the more medial side of the base of scapular spine and the more inferior of scapular spine. This can make the firm suture tied over scapular spine during repair SLAP and the Bankart lesion, and also prevent the injury of suprascapular nerve.

• Nuclear Engineering and Technology
• /
• v.35 no.4
• /
• pp.356-368
• /
• 2003

Material properties such as coolant specific heat, film heat transfer coefficient, cladding thermal conductivity, surface diffusion coefficient of the multi-bubble are improved in MACSIS-Mod1. The axial power and flux profile module was also incorporated with irradiation history. The performance and feasibility of the updated driver fuel pin have been analyzed for nominal parameters based on the conceptual design for the KALIMER breakeven core by MACSIS-MOD1 code. The fuel slug centerline temperature takes the maximum at 700mm from the bottom of the slug in spite of the nearly symmetric axial power distribution. The cladding mid-wall and coolant temperatures take the maximum at the top of the pin. Temperature of the fuel slug surface over the entire irradiation life is much lower than the fuel-clad eutectic reaction temperature. The fission gas release of the driver fuel pin at the end of life is predicted to be $68.61\%$ and plenum pressure is too low to cause cladding yielding. The probability that the fuel pin would fail is estimated to be much less than that allowed in the design criteria. The maximum radial deformation of the fuel pin is $1.93\%$, satisfying the preliminary design criterion ($3\%$) for fuel pin deformation. Therefore the conceptual design parameters of the driver fuel pin for the KALIMER breakeven core are expected to satisfy the preliminary criteria on temperature, fluence limit, deformation limit etc.

• Asian-Australasian Journal of Animal Sciences
• /
• v.11 no.5
• /
• pp.463-469
• /
• 1998

Factor analysis was applied as a multivariate statistical technique to official genetic evaluations of type classification traits for 1,265,785 Holstein cows and 10,321 sires computed from data collected between August 1982 and June 1994 in Canada. Type traits included eighteen linear descriptive traits and eight major score card traits. Principal components of the factor analysis showed that only five factors explain the information of the genetic value of linear descriptive traits for both cows and sires. Factor 1 included traits related to mammary system, like texture, median suspensory, fore attachment, fore teat placement and rear attachment height and width. Factor 2 described stature, size, chest width and pin width. These two factors had a similar pattern for both cows and sires. In constrast, Factor 3 for cows involved only bone-quality, while in addition for sires, Factor 3 included foot angle, rear legs desirability and legs set. Factor 4 for cows related to foot angle, set of rear leg and leg desirability, while Factor 4 related to loin strenth and pin setting for sires. Finally, Factor 5 included loin strength and pin setting for cows and described only pin setting for sires. Two factors only were required to describe score card traits of cows and sires. Factor 1 related to final score, feet and legs, udder traits, mammary system and dairy character, while frame/capacity and rump were described by Factor 2. Communality estimates which determine the proportion of variance of a type trait that is shared with other type traits via the common factor variant were high, the highest ${\geq}$ 80% for final score, stature, size and chest width. Pin width and pin desirability had the lowest communality, 56% and 37%. Results indicated shifts in emphasis over the twelve-year period away from udder traits and dairy character, and towards size, scale and width traits. A new system that computes fmal score from type components has been initiated.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.210-215
• /
• 2003

A terminal pin, which is a part of high-voltage capacitors, has a head section of plate-shaped geometry with 0.8 thickness. The current manufacturing process, in which the head section is welded on the body part, has given wide deviations of part qualities such as geometrical accuracy, mechanical strength and electrical stability. In this paper, a cold forging process sequence was designed in order to produce the terminal pin as one piece. The plate-shaped head section requires an upsetting in the lateral direction of a cylindrical billet, which is followed by a blanking process. The deformed geometry of the upsetting, however, could not be predicted precisely by intuition since metal flows of an axial and a lateral direction of the cylindrical billet would occur simultaneously. Therefore, the geometry of the initial billet was determined by three dimensional finite element analysis in order to avoid defects in blanking process and intermediate forging processes were designed by applying design rules and two dimensional FE analysis. In addition, cold forging tryouts were conducted by using the die sets which were manufactured based on the designed process sequence.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.159-162
• /
• 2001

A combined finite element and experimental study based on the characteristic length method is performed to investigate the strength and behavior of the pin joint in composite control rod. The failure is estimated by the Yamada-Sun and Tsai-Wu criteria on the characteristic curve. The gap elements are used to simulate the contact between the pin and the composite fitting with hole. The accuracy and applicability of the method are validated by the joint tests. All the specimens were failed in the bearing mode in the test and finite element analysis, and good agreement was found between the predicted and test results on the joint strength of composite control rod.