• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.10
• /
• pp.909-919
• /
• 2013

Pneumatic exciters can be good replacements of electrodynamic, piezoelectric and hydraulic exciters owing to simple structure and large exciting force. One problem to be solved is a slow response caused by compressibility of air. Desirable frequency response characteristics of exciter are constant magnitude and zero degree phase, because users want no time delay between input signal and output force. For this reason, frequency range of pneumatic exciters is limited about 0~1 Hz. Therefore, expansion of frequency range is an important issue when designing the pneumatic exciter. In this paper, the pneumatic exciter which has same structure with active pneumatic isolator is dealt with. The dynamic characteristics are presented, and its limitation of expanding frequency range is shown based on analytical studies. Then the pneumatic exciter with dual-chamber is suggested to overcome this problem. Based on simulation study, a design method is presented.

• ETRI Journal
• /
• v.38 no.4
• /
• pp.787-797
• /
• 2016

Mining, construction, and other special vehicles for heavy use are designed to work under high-performance and off-road working conditions. The driving and executive mechanisms of the support structures and superstructures of these vehicles frequently operate under high loads. Such high loads place the equipment under constant risk of an accident and can jeopardize the dynamic stability of the machinery. An experimental investigation was conducted on a refuse collection vehicle. The aim of this research was to determine the working conditions of a real vehicle: the kinematics of the waste container, that is, a hydraulic rotate drum for waste collection; the dynamics of the load manipulator (superstructure); the vibrations of the vehicle mass; and the strain (stress) of the elements responsible for the supporting structure. For an examination of the force (weight) on the rear axle of a heavy vehicle, caused by its own weight and additional load, a universal measurement system is proposed. As a result of this investigation, we propose an alternative system for continuous vehicle weighing during waste collection while in motion, that is, an on-board weighing system, and provide suggestions for measuring equipment designs.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.164-173
• /
• 2006

In the electro-hydraulic injector for the common rail Diesel fuel injection system, the injection nozzle is being opened and closed by movement of a injector's needle which is balanced by pressure at the nozzle seat and at the needle control chamber, at the opposite end of the needle. In this study, the piezo actuator was considered as a prime movers in high pressure Diesel injector. Namely a piezo-driven Diesel injector, as a new method driven by piezoelectric energy, has been applied with a purpose to develop the analysis model of the piezo actuator to predict the dynamics characteristics of the hydraulic component(injector) by using the AMESim code. Aimed at simulating the hydraulic behavior of the piezo-driven injector, the circuit model has been developed and verified by comparison with the experimental results. As this research results, we found that the input voltage exerted on piezo stack is the dominant factor which affects on the initial needle behavior of piezo-driven injector than the hydraulic force generated by the constant injection pressure. Also we know the piezo-driven injector has more degrees of freedom in controlling the injection rate with the high pressure than a solenoid-driven injector.

• Journal of the Korean Ceramic Society
• /
• v.19 no.4
• /
• pp.293-299
• /
• 1982

The effects of $MnO_2$ and $Cr_2O_3$ on the Piezoelectrictric properties of Pb(Mg1/2W1/2)0.3 Ti0.4 Zr0.3O3 Ceramics. Electromechanical properties in the system in connection with the sintering temperature and the effects of $MnO_2$ and $Cr_2O_3$ addition. The dielectric constant of the ceramics decreased with the additions of $MnO_2$ while the additions of $Cr_2O_3$ increased the value. The Planar coupling factor (Kp) of the ceramics with 0.2wt% $MnO_2$ and with 0.2wt% $Cr_2O_3$ gave the highest value of 0.52 and 0.513 as sintered at 106$0^{\circ}C$, 108$0^{\circ}C$, respectively. The value of mechanical Q-factor were in parallel with the fired density of the ceramics. The optical micrography of the sintered bodies showed that the additions of $MnO_2$ promoted the grain growth, while the additions of $Cr_2O_3$ retarded the grain growth.

• Journal of the Korean Ceramic Society
• /
• v.36 no.10
• /
• pp.1108-1114
• /
• 1999

Microstructure and electrical properties of ZnO-doped (0-5 mol%) 0.05 Pb(Mn1/3Sb2/3)O3-0.95 PZT ceramics were investigated. Sintering temperature was decreased to 100$0^{\circ}C$ due to eutetic reaction between PbO and ZnO. Grain-size increased up to adding 1mol% ZnO and then decreased. Compositions of grain and grain-boundary were investigated by WDS. Lattice parameter was decreased with ZnO addition. Density increased with ZnO addition and reached to the maximum of 7.84(g/cm2) at 2 mol% ZnO. The effect of ZnO on electrical properties of PMS-PZT was investigated. At 3mol% ZnO addition electromechanical coupling factor(kp) was about 50% and relative dielectric constant($\varepsilon$33/$\varepsilon$0) was 997 Mechanical quality factor(Qm) decreased with ZnO addition. Lattice parameters and tetragonality(c/a) were measured to investigate relationship between the electric properties and substitution of Zn2+. At 3 mol% ZnO tetragonality was maximiged at c/a=1.0035 Curie temperature (Tc) decreased slightly with ZnO addition.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1465-1466
• /
• 2011

We have studied structural and electrical properties of $(Na_{0.5}K_{0.5})NbO_3$ ceramics addition with $BiTiO_3$. The $(Na_{0.5}K_{0.5})NbO_3-BiTiO_3$ ceramics were fabricated by the conventional mixed oxide method, their dielectric and piezoelectric properties were investigated with the variations of additvie amount $BiTiO_3$. At the sintering temperature of $1130^{\circ}C$, the density, dielectric constant, grain size of 0.05mol% $BiTiO_3$ specimen showed the values of 4.69 g/$cm^3$, 898 and $24.8{\mu}m$.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.5
• /
• pp.915-920
• /
• 2007

AIN-based film bulk acoustic resonator (FBAR) devices which adopt a membrane-type configuration such as Mo/AIN/bottom-metal/Si are fabricated by employing a novel process. The proposed resonator structure does not require any supporting layer above the substrate, which leads to the reduction in energy loss of the resonators. For all the FBAR devices, the frequency response characteristics are measured and the device parameters, such as return loss and input impedance, are extracted from the frequency responses, and analyzed in terms of the various metals such as Al. Cu, Mo, W used in the bottom-electrode. The mass-loading effect caused by the used bottom-electrode metals is found to be the main reason for the difference revealed in the measured characteristics of the fabricated FBAH devices. The results obtained in this study also show that the degree of match in lattice constant and thermal expansion coefficient hetween piezoelectric layers and electrode metals is crucial to determine the device performance of FEAR.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.556-560
• /
• 2002

The rheological characteristics of PNN-PZT ceramics with high electromechanical coupling factor and electricstrictive constant was investigated. Green sheets of piezoelectric PNN-PZT ceramics were made by tape-casting method with controlling the mixing ratio of a dispersant, an organic binder, and a plasticizer. When the dispersant content was 1 wt.%, the slurry showed the best rheological characteristics for tape casting. The amounts of the plasticizer and the binder was simultaneously varied in the ranges of 1.5~18 and 3~9 wt.%, respectively. When both the plasticizer and binder of 6 wt.% mixed in the solution, respectiveley, the highest green density of the sheet was obtained without macrodefects. Multilyered structures of PNN-PZT/Ag-Pd were successfully fabricated using the optimized tape casting condition. The polarization behavior of these actuators seemed to similar to typical electricstrictive polarization behavior. The multilayer ceramic actuator is about $0.6{\times}10^{-3}$ of strain.

• Journal of the Korean Vacuum Society
• /
• v.8 no.4A
• /
• pp.425-431
• /
• 1999

$Pb(Zr_{0.52}, Ti_{0.48})O_3$ (PZT) thick films as an actuating material with conducting oxides, $(La_{0.5}Sr_{0.5}) CoO_3$ (LSCO), have been fabricated by sol-gel method for Optical Micro-Electro-Mechanical System (MEMS) devices, in which PZT/LSCO/SiO2 structures were used. In order to improve the adhesion to LSCO solution in order to enhance the wetting behavior of a water-based LSCO precursor solution and further to improve the adhesion between LSCO and $SiO_2$ layers. PZT films were made using 1-3 propanediol based precursor solution which has a high viscosity and a boiling point appropriate for thick film fabrication. In the precursor solution, Ti-propoxied and Zr-propoxied are partially substituted with acetylacetone to achieve the solution stability while maintaining reactivity. Crack free PZT films (0.8~1$\mu\textrm{m}$) have been successfully fabricated at crystallization temperatures above $700^{\circ}C$. Dielectric constants and dielectric losses of the PZT films were 900~1200and 2~5%, respectively. Piezoelectric constant $d_{33}$ of the PZT films constrained by a substrate were 200pm/V at 100kV/cm.

• Journal of the Korean Ceramic Society
• /
• v.31 no.2
• /
• pp.155-160
• /
• 1994

PZT ceramics substituted by La3+ and Nd3+ were fabricated according to the formula: [Pb1-x(La or Nd)x][Zr0.58Ti0.42]1-x/4$\square$x/4O3(x=0.00, 0.02, 0.05, 0.08, 0.15, 0.20). The crystal structure and microstructure were investigated by XRD and SEM. It was observed that the phase transitions among rhombohedral, tetragonal, and cubic symmetry occured as the substitutional quantity increased. Dielectric constant, dissipation factor and piezoelectric coefficient (d33), of each sample were measured. The dielectric properties were changed as the substitutional quanity of rare earth ion increased. These changes could be explained by crystal structure and compositional fluctuaction. Its d33 was higher at tetragonal region near to phase boundry between rhombohedral and tetragonal, which was explained by reorientation of domain wall.