• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.1
• /
• pp.63-70
• /
• 2016

In this study, ash free coals(AFCs) were produced with lignite and anthracite coals in a microwave. The AFCs were analyzed with proximate analysis, fourier transform infrared spectrometry (FTIR), X-ray diffraction analysis, and thermogravimetric analysis (TGA). The extraction yields of the AFCs were 16.4 wt%, 7.6 wt% at lignite and anthracite coal, respectively. The chemical and physical properties of the AFCs were similar regardless of the original coal types. Oxidation behavior of the AFCs was investigated by supplying a mixture of 3g of AFC and 3g of electrolyte into the coin-type molten carbonate fuel cell (MCFC). For the evaluation of AFC fuel performance, electrochemical analysis of the steady-state polarization and step-chronopotentiometry were conducted based on the standard hydrogen fuel (69 mol% $H_2$, 17 mol% $CO_2$, 14 mol% $H_2O$). The AFCs showed similar electrochemical oxidation behaviors regardless of the original coal types. The overvoltage of the AFCs was larger than the hydrogen fuel, although OCV of the AFCs was higher.

• Korean Chemical Engineering Research
• /
• v.43 no.3
• /
• pp.387-392
• /
• 2005

Recently, dimethyl carbonate (DMC) is considered as an alternative of MTBE (methyl tert-butyl ether), additive for non-leaded gasoline with their fast biodegradation rate and low toxicity. DMC is usually synthesized so far by oxidative carbonylation of methanol, and recently developed synthetic process is also started with methanol. Since the phase equilibria of the system, consisted of DMC and methanol or other reaction products on different temperature and pressure is necessary for the optimum separation process design and operation. However the reported phase equilibria and physical properties for DMC mixtures in the Dortmund Data Bank (DDB; thermodynamic property data bank) are quite rare. Besides, infinitely dilute properties are not found. In this work, isothermal vapor-liquid equilibria at 333.15 K for methanol+DMC binary system and mixing properties, excess molar volume and viscosity deviation at 298.15 K are directly measured and correlated. Additionally, infinitely dilute activity coefficient of methanol in the DMC solvent at three different temperatures are measured and compared with predicted values using modified UNIFAC (Dortmund).

• The Korean Journal of Nuclear Medicine
• /
• v.24 no.1
• /
• pp.101-107
• /
• 1990

To develop $^{131}I-labelled$ m-iodobeneylguanidine $(^{131}I-MIBG)$, various experiments such as synthesis of MIBG, establishment of labelling conditions, determination of radiochemical purity, and examination of stability were carried out. 1) m-Iodobenzylguanidine (MIBG) sulfate was synthesized with a total yield of 62.4% by the condensation of m-iodobenzylamine hydrochloride with cyanamide via MIBG bicarbonate. Its physical properties, IR, $^1H-NMR$, and elemental analysis data were nearly identical to those of literature. 2) Freeze-dried or vacuum-dried kit vials were prepared from the mixture so as to contain MIBG (2 mg), ascorbic acid (10 mg), copper (II) sulfate (0.14 mg), and tin (II) sulfate (0.5 mg) per vial. Copper ( I ) catalyzed radioiodination of MIBG was carried out using kit vials and 0.01 M $H_2SO_4$ as solvent at $100^{\circ}C$ for 30 min under nitrogen atmosphere (optimal conditions). Labelling yield was 98% and radiochemical purity was 99.5%, respectively. 3) Solid-phase radioiodination of MIBG was carried out at $155^{\circ}C$ for 30 min using the prepared vials to contain MIBG (2 mg) and ammonium sulfate (10 mg). Duplicate reactions under the same conditions showed labelling yield of 95% and radiochemical purity of 99.5%. 4) $^{131}I-MIBG$ prepared either by catalytic or by solid-phase exchange method showed radio-chemical purity of 99% even after 3 days storing at room temperature.

• Journal of Sericultural and Entomological Science
• /
• v.50 no.2
• /
• pp.71-75
• /
• 2012

Silk is a natural polymer that has the advantages of the biocompatibility, excellent mechanical strength, low immune rejection, and molding facility. But silk does not dissolve easily in water or general solvent. To investigate the characteristics of silk biological membranes according to dissolving condition of silk fibroin, we made the silk biological membranes using silk fibroin solutions with different amount and dissolving time of silk. The characterizations of the silk biological membranes such as morphology, structure, and mechanical strength were observed. Although each biological membrane has the same fibroin content, there was a significant difference in the thickness and transparency. But there was no significant change in the molecular weight of the silk fibroin solutions and morphology of silk biological membranes. We were established the manufacturing condition for silk fibroin biological membrane. So we expect that the conditions will help in the development of medical supplies in the future.

• Korean Chemical Engineering Research
• /
• v.59 no.3
• /
• pp.326-332
• /
• 2021

In this study, a spherical carbon composite material containing nano-silicon was synthesized using hydrothermal synthesis, and coated with petroleum pitch to prepare an anode material to investigate the electrochemical characteristics. Hydrothermal synthesis was performed by varying molar concentration, and the pitch was coated using THF as an organic solvent to prepare a composite material. The physical properties of anode materials were analyzed using SEM, EDS, XRD and TGA, and the electrochemical performances were investigated by cycle, C-rate, cyclic voltammetry and electrochemical impedance tests in 1.0 M LiPF₆ electrolyte (EC : DMC : EMC = 1 : 1 : 1 vol%). The pitch-coated silicon/carbon composite (Pitch@Si/C-1.5) with sucrose of 1.5 M showed a spherical shape. In addition, a high initial capacity of 1756 mAh/g, a capacity retention ratio of 82% after 50 cycles, and an excellent rate characteristic of 81% at 2 C/0.1 C were confirmed.

• Analytical Science and Technology
• /
• v.22 no.4
• /
• pp.302-306
• /
• 2009

A trace amount of boron in steel significantly influences its mechanical and physical properties. A prompt gamma ray activation analysis (PGAA) method is used to measure boron in low alloy steel samples of KRISS 101-01-C21~C26. NIST SRMs of 362, 364, 1761 and 1767 serve as the control standards to validate the measurement method. The measured values of the NIST SRMs are consistent with their certified values within the expected uncertainties, except for that of NIST SRM 362. Experimental uncertainties are evaluated according to the guidelines given by the International Organization for Standardization (ISO). The expanded uncertainties are calculated with a coverage factor of 2, at approximately 95% confidence level. The calculated relative expanded uncertainties of boron mass fractions are between 3% and 7% at the mg/kg level. The results are compared with the results measured by the solvent extraction-inductively coupled optical emission spectrometry (ICP/OES) method.

• Applied Chemistry for Engineering
• /
• v.29 no.3
• /
• pp.336-341
• /
• 2018

In general, the synthesis of poly(3-hexylthiophene)(P3HT)-based block copolymers requires at least a 4-5 step process. To control the molecular weight, molecular weight distribution, and block ratio, the reaction conversion and time should be monitored. In addition, the reaction scale usually limited to several mg to g was difficult to increase due to the limitations of living radical polymerizations. In this study, we synthesized P3HT-b-poly(4-vinylprydine) (P3HT-b-P4VP) with a final product quantity of > 19 g via a 2-step synthetic method with an anionic polymerization. In this method, the molecular weight and molecular weight distribution of P3HT-b-P4VP can be well controlled without monitoring the reaction conversion. We also studied physical properties of P3HT-b-P4VP depending on different solvent systems, which were investigated by UV-vis spectroscopy, atomic force microscopy, and ultraviolet photoelectron spectroscopy.

• Journal of the Korean Society of Radiology
• /
• v.3 no.2
• /
• pp.11-16
• /
• 2009

Mercury Iodide as good sensitivity at radiation and has an easy peculiarity that operates at low voltage for other photoconductors(a-Se, a-Si, Ge, etc) Based on this characteristic, we studied about an efficiency of the digital x-ray detector in acccordance with the thickness of photoconductor. To solve the problem that is difficult to make a large area film using PVD(Physical Vapor Deposition)method, we used a PIB(Particle In Binder)method. To make a binder paste, we used a PVB(Polyvinylbutyral) as a binder and a DGME(Diethylene Glycol Monobutyl Ether), DGMEA(Diethylene Glycol Monobutyl Ether Acetate) as a solvent. Using this binder paste, we made a polycrystal mercury iodide film that has an each thickness. To evaluate the electrical properties of this films, we measured a darkcurrent, sensitivity and SNR(Signal to Noise Ratio). Mercury iodide film of the 200um thickness has good electrical properties as a result of the measurement. From this result there is a good chance that replace the existing a-Se(Amnorphous seleinum; a-se) with the mercury iodide.

• Journal of Conservation Science
• /
• v.35 no.6
• /
• pp.681-688
• /
• 2019

In this study, the characteristics of natural and synthetic adhesives used in woodcraft were evaluated. The pattern of deterioration of wood and adhesives according to changes in temperature and humidity were compared. For materials, one type of anlmal glue, three kinds of polyvinyl acetate adhesives, one type of epoxy adhesive and one type of zelkova wood were selected. Characteristics of physical and chemical characteristics, weather resistance and drying speed assessment were carried out. The adhesion characteristic evaluation showed that the adhesion strength of anlmal glue and one type of polyvinyl acetate adhesive were 6.54 N/㎟ and 7.01 N/㎟, pH meter of anlmal glue and polyvinyl acetate adhesives was pH 7.03 and pH 3.32-3.59 which were range of available as an adhesive. According to the test results of weather resistance, epoxy adhesives had the highest decreasing value in adhesion strength after deterioration. In the reversible test of the adhesive, it was found to be highly reversible in NaOH, a soluble solvent excluding epoxy, but attention is required when using the wood since it may show discoloration during processing.

• Polymer(Korea)
• /
• v.38 no.4
• /
• pp.535-543
• /
• 2014

This work, which was about the synthesis of naphthalimidopropyl acrylate and GMA copolymers and their physical properties, investigated the compositions of the copolymer, the reactivity ratios of the monomer, resonance effect (Q), polar effect (e) and fluorescence of naphthalene. Azobisisobutyronitronitryl (AIBN) as an initiator was employed at $60^{\circ}C$ with dimethylformamide (DMF) of solvent for the copolymerization of NIPA. $r_1$ was found to be higher than $r_2$ from the reactivity ratios of the monomer obtained from Fineman-Ross (F-R), Kelen-$T{\ddot{u}}d{\ddot{o}}s$(K-T) methods. NIPA was found to be more copolymerized than GMA. $r_1{\cdot}r_2$ product was lower than 1, copolymerization was maked random-alternating type. The fluorescence spectrum of these polymers showed a weak monomer fluorescence band at 380 nm and a strong excimer fluorescence band at about 460 nm. Fluorescence life time of NIPA monomer showed fluorescence cover with UV 355 nm at room temperature, and life time showed $5.1449{\times}10^{-7}s$.